Planet ICS-2200T Manual de usuario
Industrial 2-/4-port RS232/422/485
Serial Device Server
ICS-2200T/ICS-2400T
Quick Installation Guide
Table of Contents
1 Package Contents..................................................................... 3
2. Requirements............................................................................ 4
3. Hardware Introduction ............................................................... 5
3.1 Front Panel ........................................................................ 5
3.2 Wiring the Power Inputs...................................................... 6
3.3 Serial Port PIN Assignment .................................................. 7
4 Web Login ................................................................................ 8
4.1 Starting Web Management ................................................. 8
4.2 Logging in to the Industrial Serial Server.............................. 8
5. Remote Console Telnet Login.....................................................10
5.1 Logging in to the Remote Console Interface.........................10
6. Getting Started with VCOM Utility ..............................................11
6.1 Installation of VCOM Utility .................................................11
6.2 Searching Serial Device Server ...........................................12
6.3 Serial Server Login ............................................................12
6.4 Serial Server Setting..........................................................13
6.5 COM Port Mapping .............................................................14
7. RecoveringBacktoDefaultConguration ...................................15
8. Customer Support ....................................................................16
3
1 Package Contents
Thank you for purchasing PLANET ICS-2200T and ICS-2400T Industrial
Multi-port Serial Device Servers. “Industrial Serial Server” is used
as an alternative name in this Quick Installation Guide.
Open the box of the Industrial Serial Server and carefully unpack it.
The box should contain the following items:
The Industrial Serial Server x 1 Quick Installation Guide x 1
Wall Mounting Kit x 1 Dust Cap x 2
If any item is found missing or damaged, please contact your local
reseller for replacement.
4
2. Requirements
The Industrial Serial Server provides remote login interface for
management purposes. The following equipment is necessary for
further management:
Workstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS
X or later, Linux, UNIX, or other platforms are compatible with TCP/
IP Protocols.
Ethernet Port Connection
Workstations are installed with Ethernet NIC (Network Interface
Card)
Network cables -- Use standard network (UTP) cables with RJ45
connectors.
The above PC is installed with Web browser
Note
It is recommended to use Internet Explorer 8.0 or above
to access the Industrial Serial Server.
Note
If the Web interface of the Industrial Serial Server is not
accessible, please turn off the anti-virus software or fire-
wall and then try it again.
5
3.Hardware Introduction
3.1 Front Panel
ICS-2200T ICS-2400T
PWR1 PWR2 Fault
SYS
E2
E1
LNK/
ACT
LNK/
ACT
Rx Tx
Rx Tx
P1
P2
RS232/422/485
P1
P2
ICS-2400T
E2
E1
P1 P3
PWR1 PWR2
I/O
Fault
P1
Rx Tx Rx Tx
Rx Tx Rx Tx
SYS
LNK/
ACT
LNK/
ACT
P3
P2 P4
P2
RS232/422/485
P4
6
3.2 Wiring the Power Inputs
The upper panel of the Industrial Serial Server indicates a DC inlet
power socket and consists of one terminal block connector within 6
contacts. Please follow the steps below to insert the power wire.
1.Insert positive/negative DC power wires into Contacts 1 and 2 for
Power 1, or Contacts 5 and 6 for Power 2. Figure 3-1 and 3-2
show PWR1 and PWR2 of the Industrial Serial Server.
ICS-2200T: 12~48V DC
V1+ V1- V2+ V2-
PWR1 PWR2Fault
DC Input:
12-48V , 1Amax.
1 2 3 4 5 6
Figure 3-1: ICS-2200T Upper Panel
ICS-2400T: 12~48V DC
1A@24V
V1+ V1- V2+ V2-
PWR1 PWR2Fault
DI1 DO0 DO1DI0 GNDGND
DC Input:
12-48V , 1Amax.
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-2: ICS-2400T Upper Panel
7
2. Tighten the wire-clamp screws for preventing the wires from loos-
ening.
1 2 3 4 5 6
V1+ V1- V2+ V2-
Power 1 Fault Power 2
Figure 3-3: PWR1 & PWR2 pin of terminal block.
Note
The wire gauge for the terminal block should be in the
range from 12 to 24 AWG.
3.3 Serial Port PIN Assignment
8
4 Web Login
4.1 Starting Web Management
The following shows how to start up the Web Management of the
Industrial Serial Server. Note the Industrial Serial Server is congured
through an Ethernet connection. Please make sure the manager PC
must be set to the same IP subnet address.
For example, the default IP address of the Industrial Serial Server is
192.168.0.100, then the manager PC should be set to 192.168.0.x
(where x is a number between 1 and 254, except 100), and the
default subnet mask is 255.255.255.0.
Ethernet
PC/Workstation with Web Browser
IP Address:192.168.0.x
RJ45 UTP Cable
ICS Serial Device Server
IP Address:192.168.0.100
Figure 4-1: IP Management Diagram
4.2 Logging in to the Industrial Serial Server
1. Use Internet Explorer 8.0 or above for Web browser and enter IP
address http://192.168.0.100 (the factory-default IP address) to
access the Web interface.
2. When the following dialog box appears, please enter the default user
name “admin” and password “admin” (or the password you have
changed before) as shown in Figure 4-2.
Default IP Address: 192.168.0.100
Default User Name: admin
Default Password: admin
Figure 4-2: Login Screen
9
3. After entering the password, the main screen appears as shown in
Figure 4-3.
Figure 4-3: Web Main Screen of Industrial Serial Server
4. The Server Menu on the middle of the Web page lets you access all
the functions and statuses the Industrial Serial Server provides.
Now, you can use the Web management interface to continue the
Serial Server management. Please refer to the user manual for more.
Note
1. For security reason, please change and memorize
the new password after this first setup.
2. Only accept command in lowercase letter under web
interface.
10
5. Remote Console Telnet Login
5.1 Logging in to the Remote Console Interface
The Industrial Serial Server also supports Telnet for remote
management. You can use Telnet to open a terminal session over
one of the Ethernet ports. The Serial Server asks for user name and
password for remote login when using Telnet; please use the following
defaultIPaddress,usernameandpasswordfortherst-timelogin.
Default IP Address: 192.168.0.100
Default Username: admin
Default Password: admin
You will be presented with a text menu displaying the Industrial Serial
Server’s general settings, which you will be able to view and modify.
Please refer to User Manual for a description of the available settings.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Servidor de Planet
Planet
Planet NAS-7101 Manual de usuario
Planet
Planet MCU-1400 Manual de usuario
Planet
Planet ICS-2102ST Manual de usuario
Planet
Planet NAS-7202 Manual de usuario
Planet
Planet IVS-H125 Manual de usuario
Planet
Planet IVS-H120 Manual de usuario
Planet
Planet NAS-7103 Manual de usuario
Planet
Planet IVS-110 Manual de usuario
Planet
Planet SIP-50 Manual de usuario
Planet
Planet NAS-7400 Manual de usuario
Planet
Planet 1-Bay SATA NAS Server NAS-7100 Manual de usuario
Planet
Planet ICS-2100T Manual de usuario
Planet
Planet NAS-1000 Manual de usuario
Planet
Planet ICS-11 Series Manual de usuario
Planet
Planet NAS-7102 Manual de usuario
Planet
Planet NAS-7410 Manual de usuario
Planet
Planet 1-Bay SATA NAS Server NAS-7100 Manual de usuario
Planet
Planet NAS-1101 Manual de usuario
Planet
Planet NAS-3410 Manual de usuario
Planet
Planet IVS-100 Manual de usuario
