Planar PX191 Manual de usuario
PLANARLCDMONITORPX191MANUALwww.planar.com
1
English
Usage Notice
Precautions ................................................................................. 2
Introduction
About the Product ........................................................................ 3
Package Overview ...................................................................... 4
Installation
Product Overview ........................................................................ 5
Connecting the Displa ............................................................... 7
User Controls
Front Panel Controls ................................................................... 10
How to Use the OSD Menus........................................................ 11
On-Screen Displa Menus .......................................................... 12
Appendices
Troubleshooting .......................................................................... 16
Warning Signal ........................................................................... 17
Product Dimensions .................................................................... 18
Compatibilit Modes ................................................................... 19
Table of Contents
English 2
Usage Notice
Warning- To prevent the risk of fire or shock hazards, do not
expose this product to rain or moisture.
Warning- Please do not open or disassemble the product as this
may cause electric shock.
Precautions
Follow all warnings, precautions and maintenance as recommended
in this users manual to maximize the life of your unit.
Do:
qTurn off the product before cleaning.
qUse only a dry soft cloth or clean room wiper when cleaning the
LCD panel surface.
qUse a soft cloth moistened with mild detergent to clean the
display housing.
qUse only high quality and safety approved AC/DC power
adapter.
qDisconnect the power plug from AC outlet if the product is not
used for a long period of time.
Dont:
qDo not touch the LCD panel surface with sharp or hard ob ects.
qDo not use abrasive cleaners, waxes or solvents for your
cleaning.
qDo not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- Place in direct sunlight.
3
English
Introduction
About the Product
Having a 19 flat panel screen with an active matrix, thin-film transistor
(TFT) liquid crystal display (LCD) , this product also demonstrates
following outstanding features:
qAnalog and Digital signal input
qActive matrix TFT LCD technology
q1280 x 1024 addressable pixels
q19 diagonal screen size
q31.5 ~ 80 kHz horizontal scan
q56 ~ 75 Hz refresh rate
qVESA wall mountable
qAuto-ad ustment
qMultilingual OSD user controls
qAd ustment stand design brings users the conveniences for easy
storage and VESA Mounting applications
qVESA DPMS power saving
qKensington lock capability
English 4
Package Overview
LCD Display
VGA Signal Cable
Power Adapter
Power Cord
DVI-D Cable
Users Manual Quick Start Guide Planar Product
Family CD
5
English
Installation
Product Overview
u Front View
uRear View
Connector Ports
Kensington Lock
Panel
Controls
Stand
LCD Display
VGA Input
DC
Power-In
Digital Port
English 6
Warning!
Please must select the proper screws!
The depth from plastic back cover to the bottom of the screw hole is 8mm.
The spec is M4 screw.
VESA Mount on your monitor
This monitor conforms to the VESA Flat Panel Mounting Physical
Mounting Interface Standard which defines a physical mounting interface
for flat panel monitors, and corresponding standards for flat panel
monitor mounting devices, such as wall and table arms.The VESA
mounting interface is located on the back of your monitor.
To mount the monitor on a swing arm or other mounting fixture,
follow the instruction included with the mounting fixture to be used.
VESA
Mounting
Interface
Slots
100mm
100mm
7
English
To setup this display, please refer to the following figure and procedures.
1. Be sure all equipments are off.
2. Connect the DC power cord to the power connector; plug one end of the
AC power cord into the power adapter, and then the other end into an
electrical outlet(u).
3. Connect the VGA signal cable from display VGA input connector to the
15-pin connector of your host computer and tighten the screws(v).
4. For the PC with DVI digital output: Connect the DVI signal cable to the
connector of the display card in your computer; connect the other side to
the DVI-D input port of your display. Tighten the screws(w).
5. Turn on your computer and display.
Note: To ensure the LCD displa can work well with our computer, please
configure the displa mode of our graphic card to make it less than or equal
to 1280 x 1024 resolution and make sure timing of the displa mode is
compatible with the LCD displa . We have listed the Compatibilit Modes
of this LCD displa in appendices for our reference.
ConnectingtheDisplay (Figure8.1)
English 8
Figure 8.1
VGA
Cable
Power Adapter
& Power Cord
DVI-D Cable
Otros manuales para PX191
1
Tabla de contenidos
Otros manuales de Monitor de Planar
Planar
Planar PE190 Manual de usuario
Planar
Planar PL1910 M Manual de usuario
Planar
Planar PT2285PW Manual de usuario
Planar
Planar LX1250TI Manual de usuario
Planar
Planar LO552 Manual de usuario
Planar
Planar PS5500 Manual de usuario
Planar
Planar PL2010 Manual de usuario
Planar
Planar PL1911M Manual de usuario
Planar
Planar Dome E2c Manual de usuario
Planar
Planar PS5074K Manual de usuario
Planar
Planar PY5500 Manual de usuario
Planar
Planar LED2210MW Manual de usuario
Planar
Planar CleanPole M4POLE-PS Manual de usuario
Planar
Planar PXN2700 Manual de usuario
Planar
Planar PX1910M Manual de usuario
Planar
Planar PL2010M Manual de usuario
Planar
Planar PT3270Q Manual de usuario
Planar
Planar PT191MU Manual de usuario
Planar
Planar EL320.240-FA3 Manual de usuario
Planar
Planar Dome C3 Manual de usuario
