Pizzacraft PizzaQue PC7001 Manual de usuario
PizzaQue®
Pizzacraft®
PC7001
CS040215
©The Companion Group 2014
1250 9th Street, Berkeley, CA 94710
800-521-0505
IMPORTANT: This instruction manual contains important information necessary for the proper
assembly and safe use of the appliance.
Read and follow all warnings and instructions carefully before assembling and using the appliance. Keep this
manual for future reference.
Makes great tasting,
traditional Italian pizza –
with bubbly cheese, crispy
crust & toasty toppings.
OWNER’S MANUAL
Pizza Kit
for Kettle Grills
Safety Information .............................. 3
Assembly Instructions ....................... 4
Fitting Instructions ............................ 13
Lighting Instructions ......................... 16
Cooking Instructions......................... 17
Care and Maintenance....................... 18
Troubleshooting................................. 19
Replacement Parts ............................ 20
Accessories ....................................... 21
Warranty and Registration ................ 22
TABLE OF CONTENTS
3
SAFETY INFORMATION
IMPORTANT: Before you begin...
AS WITH ALL CHARCOAL GRILLS, THERE CAN BE SOME RISKS INVOLVED AND WE
WANT YOU TO STAY SAFE WHILE USING OUR PRODUCT.
1. Please read the following instructions and safety warnings completely before use. Keep this booklet for future
reference and feel free to contact us with any questions at 800-521-0505.
2. Always exercise caution when operating your kettle grill with the PizzaQue®Pizza Kit.
3. Your kettle grill with the PizzaQue®Pizza Kit will be HOT during and after cooking and should never be left
unattended while it is HOT.
4. Do NOT leave children, infants or pets unattended near your kettle grill with the PizzaQue®Pizza Kit while
it is still HOT.
5. Use in well-ventilated OUTDOOR areas only.
6. Use far away from combustible materials.
7. Do NOT remove ashes until charcoal is completely burned off.
8. When in use, access to a re extinguisher is highly recommended.
9. Intended for use with charcoal style kettle grills only.
10. Do NOT use in high winds. Use caution when wearing loose clothing while operating your kettle grill with
the PizzaQue®Pizza Kit.
11. Do NOT use other brand pizza stones in your kettle grill with the PizzaQue®Pizza Kit, as they may break
due to the high temperatures achieved by this kit.
12. Heat resistant gloves are highly recommended when handling your kettle grill with the PizzaQue®Pizza Kit
during and after use.
4
ASSEMBLY INSTRUCTIONS
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents and hardware
contents list. Do not discard packing materials before assembly is complete.
If any part is missing or damaged, do not attempt to assemble the product. Call customer service at 800-521-0505.
To watch assembly video go to: www.pizzaque.com
Estimated assembly time: 30 minutes
Tools required - #2 Phillips screw driver and Crescent wrench (not included)
PACKAGE CONTENTS:
1. 15” pizza stone
2. Rear panel (for 22.5” grills ONLY)
3. Side panels (Qty 2)
4. Thermometer
5. Clips (Qty 5)
6. Wire door frame
7. Pizza stone supports (Qty 2)
8. Hardware package
9. Folding aluminum peel
10. Front support tabs (Qty 2 - for 18.5” grills ONLY)
11. Charcoal fence (Qty 4 x steel mesh panels)
HARDWARE PACKAGE CONTENTS:
1. (Qty 2) M5 x 15 screws -
2. (Qty 13) M5 x 8 screws
3. (Qty 15) M5 nuts
for side panel to door
frame connection
1.
1. 2. 3.
2. 4.
3.
5.
6.
7.
8.
11.
10.
9.
5
screw placement
1. Insert short edges of wire door frame into channels on the front edge of the side panels (bottom edges of the wire door
frame and side panels should line up at -- shown in the SIDE VIEW below). Secure wire door frame to side panels by
inserting M5x15 phillips head screw through hole in side panel and side panel tab then tighten with M5 nut.
TOP VIEW
wire door frame
short edges
side panel channels
TOP VIEW
SIDE VIEW
Bottom edge of wire door frame
and side panels line up at
6
2. Attach rear panel to side panels. Make sure bottom edges of rear panel and side panels line up at and top edges align
at an angle. Secure tightly with M5x8 screws and M5 nuts. Check to conrm the bottom edge of the assembly sits at.
NOTE: One side edge of the rear panel lines up outside the side panel while the other lines up inside the side
panel.
rear panel on OUTSIDE
of left side panel
rear panel on INSIDE of
right side panel
TOP VIEW
rear panel shown in solid black
CONNECTION DETAIL
ASSEMBLY INSTRUCTIONS FOR 22.5 IN KETTLE GRILL
FRONT
at
angled
*ASSEMBLY INSTRUCTIONS FOR 18.5 IN KETTLE GRILL --> SKIP TO PAGE 10
7
3. Attach stone supports as shown (make sure that the tabs closer to the center of the pizza stone supports are face
up). Secure supports using M5x8 screws and M5 nuts.
Note the direction of the pizza stone support tabs
TOP VIEW
4. Attach thermometer by aligning probe and pins with designated holes in the (right) side panel. Secure with
thermometer probe nut.
FRONT
Make sure inner tabs are face
up for 22.5” kit setup
8
5b. WEBER 22.5” CLIP CONFIGURATION:
Attach side panel clips and rear panel clip (Qty 5 total -- 2 on each side panel and 1 on the rear panel). Clips near
front edge and clip in rear panel are mounted with the opening facing down, while the clips near the middle of
side panels are mounted with the opening facing up. Secure all clips with M5x8 screws and M5 nuts.
5a. MASTERBUILT PRO 22.5” CLIP CONFIGURATION:
Attach clip, with opening facing upward, to hole in center of rear panel. Then, attach 2 clips to side panels (1
on each side panel) so the opening of the clip is facing upward as shown below. Secure all 3 clips with M5x8
screws and M5 nuts.
Notice how individual clips are oriented
Pull rear clip all the way up
in slot and tighten securely
9
6. Construct charcoal fence. (1) Bend edge tab outward to expose u-channel and (2) slot at edge into u-channel
then (3) bend tab back over u-channel into original position to lock panels together. Repeat with all 4 panels of
the charcoal fence until you’ve create a completely enclosed shape. CAUTION: Wearing protective gloves is
strongly recommended when assembling the charcoal fence, as the edges may be sharp.
bend edge tab
outward
slot at edge
into u-channel
edge tab
u - channel
at edge
bend edge tab back inward to
original position to secure
(1)
(2)
(3)
COMPLETED 22.5” PIZZAQUE® PIZZA KIT ASSEMBLY. (Now go to step 7 for tting instructions)
10
Align top and bottom holes
on back edges of side panels
2. Rotate side panels toward each other until the holes on the back edge of both side panels line up (some force will be
needed). Use M5x8 screws and M5 nuts to secure the side panels together at back edge. NOTE: Rear panel will not be
needed for 18.5 in grill kit
ASSEMBLY INSTRUCTIONS FOR 18.5 IN KETTLE GRILL
3. Align attachment holes for pizza stone supports with designated side panel holes (make sure that the tabs closer to the
outer edge of the pizza stone supports are face up). Secure supports using M5x8 screws and M5 nuts.
Note the direction of the pizza stone support tabs
TOP VIEW
FRONT
Make sure outer tabs are face
up for 18.5” kit setup
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
