Pitco PE14D Manual de usuario

L80-045 Rev 0 (11/07)

IMPORTANT FOR FUTURE REFERENCE

Please complete this information and retain these

instructions for the life of the equipment:

Model #: __________________________

Serial #: __________________________

Date Upgraded: ____________________

Technician: ________________________

Installation Instructions for the

PE14D/PG14D

Manual Fill Option

L80-045 Rev0 (11/07) 2

Tool required to perform this upgrade:

5/32” Allen Key 5/16” Socket, Nut Driver, or Wrench

3/8” Wrench 1/2” Wrench

3/4” Wrench 7/8” Wrench

13/16” Wrench 1 1/4” Wrench

1/2” Punch Hammer

Teflon Tape #2 Phillips

Channel Locks

Before you begin :

Verify that you have all the parts for the model that you are upgrading

by checking the kit number and contents against the kit picture.

L80-045 Rev0 (11/07) 3

Ensure kit is complete. Part number B8702901-CL.

1. Qty.1 B3615401-C Bezel

2. Qty.3 PP10911 Fitting

3. Qty.1 A8017902-C Bracket

4. Qty.1 PP10830 Fitting

5. Qty.1 A1826101-C Bracket

6. Qty.1 PP10944 Knob

7. Qty.1 PP10726 Check Valve

8. Qty.2 PP10270 U-Bolt

9. Qty.2 PP10694 Screw

9. Qty.4 P0092300 Nut

10. Qty.1 A8017501 Piping

11. Qty.1 B8029301 Handle Extension

12. Qty.1 PP10945 Valve

13. Qty.1 A8017401 Piping

14. Qty.1 A6066901 Overlay

1 2 3

10 11 12

L80-045 Rev0 (11/07) 4

15. Qty.1 L80045 Instruction Manual

Exploded Part view

L80-045 Rev0 (11/07) 5

1. From the back, remove the eight 5/16” screws that hold the rear cover on.

2. With the rear of the tank exposed, remove the fill port plug with a 1/2” in

wrench. Then remove the reducer with a 7/8” wrench. Save the reducer,

as it will be reused.

3. With the nylon plug exposed it can now be removed. The hole in the tank

is smaller than the coupling. The nylon plug needs to be removed out the

rear. It can be punched out from the front inside of the tank, or pulled

from the rear. The plug will not be reused. Be sure not to damage the

threads of the coupling. Clean any debris from the reducer and the

coupling. Apply Teflon tape to the reducer and reinstall.

L80-045 Rev0 (11/07) 6

4. Apply Teflon tape to the 90° compression fitting (PP10911) and install.

Make sure the fitting is at the 3 o’clock position when fully tightened.

5. Apply the compression fitting (PP10830) to the front end of the fill

piping (A8017501) before install. Apply the remaining two 90°

compression fitting (PP10911) to each end of the supply piping

(A8017401). After each end is compressed remove the body of the fitting

6. Install the fill piping from the rear of the unit. The piping should sit on

top of the left tank support. Insert the rear end of the piping in to the rear

compression fitting and tighten the fitting.

L80-045 Rev0 (11/07) 7

7. Apply Teflon tape to the rear fitting of the supply piping. Install the

check valve (PP10726) onto the rear fitting of the supply piping with the

support bracket (A1826101-C) between the valve and fitting.

8. Install the supply piping assembly from the front. The assembly should

contain the piping, two fittings, check valve, and mounting bracket.

Mount the bracket to the bottom rear cabinet brace using the two Phillips

head screws (PP10694) and two of the six kep nuts (P0092300). When

mounted, reinstall the rear cabinet cover using the original screws.

L80-045 Rev0 (11/07) 8

9. From the front of the unit, remove the four Allen head screws with a

5/32” Allen Key. Unplug the computer and set front panel assembly

aside. Remove the heat shield via three 5/16” screws.

10.With the heat shield removed remove the no fill option cover plate. The

plate is held in place with three 5/16” screws with 3/8” kep nuts.

11. With the cover removed you should see your supply and fill piping.

L80-045 Rev0 (11/07) 9

11. Apply Teflon tape the NPT ends of the fitting bodies removed earlier.

Assemble the fittings with fill valve (PP10945). Add the knob extension

to the assembly and install. Make sure the flat side of the “D” shaft faces

the 90° fitting.

12.Install the manual fill option cover plate (A1826101-C) using the original

hardware. Install two the u-bolts (PP10270) and four kep nuts

(P0092300) and tighten.

13.Using a pair of channel locks brake off the extra studs of the U-bolts.

Reinstall the heat shield using the original hardware.

L80-045 Rev0 (11/07) 10

14.Apply the new manual fill option overlay (A6066901) to the new manual

fill option bezel (B3615401-C). With a 3/8” wrench, remove the four kep

nuts that hold the controller to the original bezel and install it onto the

new bezel using the original hardware.

15.Reconnect the controller plug and mount the bezel using the original

hardware. Install the fill knob and tighten the set screw. Make sure the

knob only travels within the markings of the overlay.

16.If a water source is available, hook it up and inspect all connection points

for leaks. If a water source is not available fill the tank with water and

inspect all connection points below the water line.

Otros manuales para PE14D

Este manual sirve para los siguientes modelos

Otros manuales de Freidora de Pitco

Pitco

Pitco Frialator SG 18 Manual de usuario

Pitco

Pitco MG14S-C/MFD Manual de usuario

Pitco

Pitco SE Series Manual de usuario

Pitco

Pitco SOLSTICE SFSSH55 Manual de usuario

Pitco

Pitco 24F Manual de usuario

Pitco

Pitco E12SS Manual de usuario

Pitco

Pitco SG14C Manual de usuario

Pitco

Pitco SSHLV14 Series Manual de usuario

Pitco

Pitco 14T Manual de usuario

Pitco

Pitco SE14 Manual de usuario

Pitco

Pitco MG14S-C/MFD Manual de usuario

Pitco

Pitco SSH Manual de usuario

Pitco

Pitco SGH50 Manual de usuario

Pitco

Pitco SE14 Manual de usuario

Pitco

Pitco FBG18 Manual de usuario

Pitco

Pitco SG14TS Manual de usuario

Pitco

Pitco E24FF Manual de usuario

Pitco

Pitco SSHLV184 Series Manual de usuario

Pitco

Pitco Frialator SG 14 Manual de usuario

Pitco

Pitco SELV14 Manual de usuario

Pitco

Pitco 45C+ Manual de usuario

Pitco

Pitco SE Series Manual de usuario

Pitco

Pitco SG Series Manual del propietario

Pitco

Pitco E400 Manual de usuario

Manuales populares de Freidora de otras marcas

Innsky

Innsky 55SA1US Manual de usuario

Falcon

Falcon G350/11 Guía del usuario

GoWISE USA

GoWISE USA GW22612 Manual de usuario

Wolf

Wolf IF15/S Manual de usuario

Electrolux

Electrolux Thermetic 9CHG583284 Guía rápida

Gourmia

Gourmia GAF799 Manual de usuario

DeLonghi

DeLonghi D677UX Manual de usuario

SEVERIN

SEVERIN DEEP FRYER - Guía del usuario

Toastmaster

Toastmaster TMFG18-NAT Manual de usuario

Domo

Domo DO465FR Manual de usuario

Henny Penny

Henny Penny PFG-691 Manual de usuario

Farberware

Farberware FBW FT 43721 B Manual de usuario

GERMANICA

GERMANICA GEAF5L3LD Manual de usuario

Roller Grill

Roller Grill MF 120 R Manual de operación

Philips

Philips HD9211 Manual de usuario

Linea 2000

Linea 2000 Domo DO536FR Manual de usuario

Lakeland

Lakeland 31796 Manual de usuario

Dash

Dash Tasti-Crisp DFAF755 Manual de usuario