©2022 RICHTECH INDUSTRIES 1.800.677.7791 RICHTECHINDUSTRIES.COM
2
1. Set the pump on a solid, level surface in the bottom of the sump pit. If necessary, use bricks / blocks to provide a solid base. Avoid
placing the pump on loose gravel, earth or sand.
2. Install discharge plumbing according to state and local codes. It is highly recommended that rigid PVC is used for the discharge
line. Installing a union in the discharge line will make it easier to remove the sump pump for maintenance. The discharge line must
be sloped downward away from the foundation to ensure that the water properly drains away and that the discharge line will not
freeze during cold spells.
3. Install a check valve in the discharge line. The check valve may be positioned just above the sump basin for ease of service and/or
replacement.
4. Assemble switch to the discharge line using the attached hose clamp. Position the switch so that when the oat is at its lowest
position it is at least 3” above the base of the pump (just above the inlet). Make sure that the switch is positioned where the oat
can move up and down freely.
5. Secure all power cords and switch cords to the discharge pipe using cable ties to prevent switch entanglement.
6. This pump uses a “piggyback” type switch to allow for the easy removal and replacement of the switch and to aid in troubleshooting
switch / pump problems. Plug the pump into the back of the switch plug.
7. Plug the switch into a ground fault circuit interrupter (GFCI) protected outlet.
8. Fill the sump basin with water until the oat rises and starts the pump cycle. The pump will stop when the water level falls to the
switch’s off position. Repeat this several times to ensure proper operation and that the switch operates freely.
9. Install the sump basin gasket / cover.
INSTALLATION
This pump is not designed to handle salt water, brine, laundry discharge, water
softener discharge or any other application which may contain caustic chemicals.
Damage to the pump may occur and will void the pump’s warranty.
NOTICE
SAFETY FIRST!
This instruction manual contains very important information for you to know and understand. This information
is provided for your safety and to help prevent equipment problems from occurring. Please observe all safety
information labeled danger, warning, caution, and notice.
RISK OF ELECTRIC SHOCK. TO REDUCE THIS RISK, OBSERVE THE FOLLOWING WARNINGS:
WARNING! To reduce the risk of electrical shock, this pump must be properly grounded in accordance with the National
Electric Code (NEC) and all applicable state and local codes and ordinances. The receptacle should be protected with a
Ground Fault Circuit Interrupter (GFCI).
WARNING! To reduce the risk of electrical shock, always disconnect the pump from the power source
BEFORE handling or servicing.
WARNING! Never remove the ground prong from the plug, or use an adapter that eliminates the ground prong.
WARNING! Never plug this pump into an electric outlet while standing on a wet surface.
WARNING! Cable should be protected at all times to avoid punctures, cuts and abrasions that may result in exposed
wiring. Never handle connected power cords with wet hands.
WARNING! This Submersible Sump Pump has not been investigated for use in or around swimming pools, marine areas,
recreational water installations, decorative fountains or any installation where human contact with the pumped uid is common.
WARNING! Do not use an extension cord. Extension cords could present a safety hazard if not properly sized, become
damaged or the connection falls into the sump pit.
RISK OF EXPLOSION. TO REDUCE THIS RISK, OBSERVE THE FOLLOWING WARNINGS:
WARNING! Do not use to pump ammable or explosive liquids such as gasoline, fuel oil, kerosene, etc.
WARNING! Do not use in a ammable or explosive atmosphere.
NOT SUITED FOR POTABLE WATER APPLICATIONS.
WARNING! Do not use this pump to transfer water that will be used for potable (drinking) water. This pump is only to be
used in applications for which it is designed.
TO REDUCE THE RISK OF HAZARDS THAT CAN CAUSE INJURY OR PROPERTY DAMAGE,
OBSERVE THE FOLLOWING WARNINGS:
CAUTION! Do not block or restrict discharge hose. Discharge hose may whip under pressure. It is strongly
recommended to use rigid piping and ttings to secure the pump in the sump basin to reduce movement.
CAUTION! Do not install the pump if it has been damaged in any way.
CAUTION! Do Not carry or lift the pump by the power cord. Use the pump’s lift ring.
WARNING INDICATES A POTENTIALLY HAZARDOUS
SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN
DEATH, SERIOUS INJURY OR MAJOR PROPERTY DAMAGE.
WARNING
CAUTION INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF
NOT AVOIDED, MAY RESULT IN MINOR INJURY OR PROPERTY DAMAGE.
CAUTION
