Pinnovators PINsub Multi System Manual de usuario
1
PINsub
Multi System
Installation Manual
Version 1.1 December 18, 2018
This manual covers the following product kits:
PINsub Multi System
Contents
1. Warnings and Agreements ........................ 2
2. Preparation ................................................ 2
3. What’s included in the Kits ........................ 3
4. Requirements: ........................................... 3
5. Connecting to the Cabinet Speaker ........... 4
6. Connecting a Subwoofer ........................... 6
7. Final Checkout ........................................... 6
8. PIN-SMX ..................................................... 6
2
1. Warnings and Agreements
Welcome! As with any Pinball Machine
modification and add on kit, there is a required level
of expertise for the installation. If you are not
proficient in basic pinball parts installation we
recommend having our kit installed by someone who
is proficient with the basics of pinball repair.
Pinnovators requires our kit be installed by an
experienced Pinball service technician with basic
electrical skills. As with any electrical piece of
equipment a danger does exist and you must agree
to not hold Pinnovators responsible for any injury,
damages, etc. before continuing.
Sound Levels: Pinnovators recommends running
your headphone and subwoofer sound levels at a
safe level to prevent long term hearing loss. For a
good example of recommend sound levels, we
recommend following suggestions given by major
audio equipment manufacturers such as Apple and
their IPod.
phys.org/news80304823.html
www.macworld.com/article/1060274/hearingprotection.html
ESD:
We recommend always discharging yourself to
a metal surface on your machine before touching
the electronics inside it.
Power Cord: ALWAYS UNPLUG THE POWER CORD
for safety when working on your pinball machine!
Playfield Propping: Pinnovators highly advises
following Playfield propping instruction for your
pinball machine. These instructions are typically
found inside the Operators manual for each
machine. Failure to follow these instructions can
cause fatal injuries or even Death. Pinnovators also
recommends having an assistant hold a propped
playfield in the up position when servicing under the
playfield.
2. Preparation
Unplug the Pinball Machine!
3
3. What’s included in the Kits
Interface Cable
and adapter and
RCA adapter.
One Velcro tie is
included to hold
the cable to the
leg of the
machine.
PINsub Multi System adapter
4. Requirements:
The Machine must have an electronic sound
board.
Please visit IPDB.ORG to learn what system your
machine has.
4
5. Connecting to the Cabinet
Speaker
Position the PINsub MS next to your cabinet
speaker.
Remove the two PosiTaps by twisting the
smaller end cap.
Remove the larger end caps.
Place the large endcaps over one of the two
speaker wires.
Twist the middle section back on to the larger
endcap. Finger tighten but don’t force it.
Leave the smaller end cap unscrewed a few
turns.
5
Insert the wires from the PINsub MS into the
hole in the small endcaps. Carefully twist the
small endcaps until finger tight.
Lightly pull on the wires to make sure they are
secure. If they come out of the Positap, try
again until they stay secure.
Using the 12 foot 3.5mm to 3.5mm supplied
subwoofer cable; plug one end into the green
female connector on the PINsub MS adapter.
Run the other end to the back of the pinball
machine.
Locate the vent hole in the right rear of the cabinet.
Push up on the vent screen to dislocate it to allow
the 3.5 mm cable to be fed down through the vent
hole.
Fish the 3.5mm subwoofer cable through the
vent hole in the bottom of the cabinet. Press up
on the screen just enough to allow the cable to
exit the system. Some screens may be difficult
to fish the wire through if they are made of
metal. You may need to loosen some bolts.
6
6. Connecting a Subwoofer
Pinnovators provides a 12 foot cable to give you the
flexibility of placing your subwoofer close by to your
pinball machine. The end of the cable has a 3.5mm
male plug on the end. Plug this end into a subwoofer
that has a 3.5mm input. Some of the Yamaha home
subwoofers only have a 3.5mm input so this will
work great in that situation. Smaller computer
subwoofer systems will also have a 3.5mm input as
shown below.
Pinnovators recommends the Polk Audio PSW10
subwoofer. This model is very affordable and
produces great sound!
Use the included 3.5mm female to RCA adapter
cable to connect to this speaker.
7. Final Checkout
Power up your subwoofer!
Power up your pinball system!
Start a game!
Make sure the front panel switch on the PinPac
Control panel is in the “UP” position if you have
the headphone kit installed.
Verify sound can be heard from the Back Box
speakers and the lower Cabinet speaker.
Adjust the subwoofer to your liking.
8. PIN-SMX
While we have your attention! Please check out
our PIN-SMX passive subwoofer mixer kit at
Pinnovators.com.
The PIN-SMX allows you to connect up to four
pinball machines to one subwoofer. Each input
is fully isolated from the others to prevent
ground loops. Each input level is fully adjustable
so you can adjust each game sub level to your
liking.
Enjoy your new Subwoofer kit!
The Pinnovators team.
Tabla de contenidos
Manuales populares de Sistema de altavoces de otras marcas
Sondpex
Sondpex Active Speaker System and Digital Music... Manual de usuario
JVC
JVC NX-PN7 Manual de usuario
Marshall Amplification
Marshall Amplification AR-DM61-BT Manual de usuario
Yamaha
Yamaha NX-A01 - Speaker Sys Manual de usuario
SE Audiotechnik
SE Audiotechnik I-LINE Manual de usuario
Gemini
Gemini WRX-843 Series Manual de usuario