Pichler Flash Manual del propietario
Wingspan 910mm
Length 750mm
2
Wing area 21.7dm
2
Wing loading 53g/dm
Flying Weight 950 ... 1150g
R/C 3 channels
Servos 3
Motor 250 ... 650W
ESC 40 ... 50A
Battery 2200 ... 3500mAh
910mm
750mm
2
21.7dm
2
53g/dm
950 ... 1150g
3 Kanal
3
250 ... 650W
40 ... 50A
2200 ... 3500mAh
95% ALMOST READY TO FLY
Flash
A
B
C
D
2
Test fit the ailerons to the wing with the hinges. If the
hinges don’t remain centered, stick a pin through the
middle of the hinge to hold it in position.
Temporary pin to
keep hinge centered.
Assemble then apply drops of thin
C/A to center of hinge,on both sides.
2x10mm 3x15mm
3
Flash
Install the rubber grommets and brass eyelets on to the
aileron servos.
Using a modeling knife, remove the covering from over
the pre-cut servo arm exit hole on the aileron servo tray
/ hatch.This hole will allow the servo arm to pass
through when installing the aileron pushrods.
Using the thread as a guide and using masking tape,
tape the servo lead to the end of the thread: carefully
pull the thread out. When you have pulled the servo
lead out, remove the masking tape and the servo lead
from the thread.
Befestigen
Secure
Drill a hole 1.5 mm
1.5 mm
Place the servo into the servo tray. Center the servo
within the tray and drill 1.5mm pilot holes through the
block of wood for each of the four mounting screws
provided with the servo.
Electric wire
Drill a hole 1.5 mm
1.5 mm
2x10mm
Befestigen
Secure
Remove the covering from the slot on the bottom of the
aileron.
Insert the control horn into the slot and secure it by A+B
Epoxy glue.
1. A/B glue
5-Min. Epoxy Klebstoff
Epoxy
2. Push in
control horn
Aileron
Aileron Control Horn
Flaslink
Pushrod wire Control horn
Repeat the procedure to install the second aileron.
After both linkages are completed. connect both of
the aileron servo loads using a Y-harness you have
purchased.
Flash
100mm
Snap keeper.
Attach the clevis to the outer hole in the servo arm.
Install a silicone tube on the clevis.
Using pliers, carefully make a 90 degree bend down
at the mark made. Cut off the excess wire, leaving
about 6mm beyond the blend.
/ Aileron Linkages
Insert the 90 degree bend down through the hole in the
control horn. Install one nylon snap keeper over the
wire to secure it to the control horn. Install the control
horn retaining screw and remove the masking tape
from the aileron.
4
Bend and cut.
Silicone Tube
Installing the aileron linkages as pictures below.
Motoreinbau / Motor Installation
Elevator install as same as the way of aileron.
Please see pictures below.
/ Horizontal stabilizer
3x15mm
Put the horizontal into the fuselage.
horizontal stabilizer in its slot. Make sure the horizontal
stabilizer is square and centered to the fuselage by
taking measurements, but don’t glue anything yet.
Check the fit of the
Flash
After the epoxy has fully cured, remove the masking
tape or T-pins used to hold the stabilizer in place and
carefully inspect the glue joints. Use more epoxy to fill in
any gaps that may exits that were not filled previously
and clean up the excess using a paper towel and
rubbing alcohol.
C/A glue.
With the horizontal stabilizer correctly aligned,mark the
shape of the fuselage on the bottom of the tail plane
using a water soluble / non permanent felt-tip pen.
Remove covering film on glueing areas.
ATTENTION: Do not cut into the wood.
Remove the stabilizer. Using the lines you just drew as
a guide, carefully remove the covering from between
them on the bottom of the tail plane using a modeling
knife.
B B
A A
A A
A = A
Elevator and Main wing must be aligned parallel to
each other
Mark line
When you are sure that everything is aligned correctly,
mix up a generous amount of 5- minute epoxy. Apply a
thin layer to the bottom of the stabilizer mounting area
and to the stabilizer mounting platform sides in the
fuselage. Slide the stabilizer in place and re-align.
Double check all of your measurements one more time
before the epoxy cures. Remove any excess epoxy
using a paper towel and rubbing alcohol and hold the
stabilizer in place with T-pins or masking tape.
5
Using a modeling knife, remove the covering from over
the pre-cut servo arm exit hole on the horizontal
stabilizer servo tray / hatch.
A/B Epoxy glue
Flash
C/A glue.
Mark line
Use a pen to mark the position of the mount on the
covering
Using a ruler and sharp knife, carefully cut through and
remove the covering film as shown.
Attach the mount in place using C/Aglue.
Place the servo into the servo tray. Center the servo
within the tray and drill 1.5mm pilot holes through the
block of wood for each of the four mounting screws
provided with the servo.
Drill a hole 1.5 mm
1.5 mm
Befestigen
Secure
2x10mm
Remove the covering from the slot on the top of the
elevator. Insert the control horn into the slot and secure
it byA+B Epoxy glue.
Elevator
control horn
Top side
2. Push in
1. A+B Epoxy glue
Flaslink
Pushrod wire
Servo arm
Silicone Tube
100mm
Snap keeper.
Elevator control horn and install as same as the
way of aileron. Please see pictures below.
linkage
6
Flash
7
Akku Battery
Receiver
Regler ESC
Seitenflosse / Vertical stabilizer
Using a modeling knife, remove the covering on the slot
of the vertical stabilizer. Mix up a generous amount of
30 minute epoxy. Apply a thin layer to the slot in the
vertical stabilizer. Slide the vertical stabilize into the
mounting platform of the horizontal stabilize. Using a
triangle, check to ensure that the vertical stabilizer is
aligned 90 degree to the horizontal.
Attach into the fuselage.
in position.
the wing Screw the wing panel
Secure
Open and close
Install the spinner backplate, propeller and spinner
cone. The spinner cone is held in place using two
3mm x 15 mm machine screws.
Receiver, ESC And Battery
Empfänger, Regler und Akku
Tragflächen / Main Wings
Spinner
1. A/B Epoxy glue
2. Push in
o
90 C/A glue.
Flash
10 mm
10 mm
7 mm
7 mm
65mm
65mm
65mm
8
Copyright © PICHLER Modellbau
www.pichler-modellbau.de
Tabla de contenidos
Otros manuales de Juguete de Pichler
Pichler
Pichler Domino 2 C6986 Manual de usuario
Pichler
Pichler SUPRA FLY 60 Manual de usuario
Pichler
Pichler PICHLER BERGFALKE 3000 Manual de usuario
Pichler
Pichler KILLER HAI Manual del propietario
Pichler
Pichler OV-10 BRONCO Manual de usuario
Pichler
Pichler Charisma Manual de usuario
Pichler
Pichler Amethyst II Manual de usuario
Pichler
Pichler Joker XL Manual de usuario
Pichler
Pichler SKY MASTER C4953 Manual de usuario
Pichler
Pichler DALOTEL 1500 Manual de usuario
Pichler
Pichler DOMINO 3 Manual de usuario
Pichler
Pichler JOKER C7115 Manual de usuario
Pichler
Pichler MINI DOMINO C9795 Manual de usuario
Pichler
Pichler Douglas DC-3 Manual de usuario
Pichler
Pichler ALPHA JET C9655 Manual de usuario
Pichler
Pichler XTREME V3 Manual de usuario
Pichler
Pichler Edge V3 Indoor Manual de usuario
Pichler
Pichler Edge V3 Indoor Manual de usuario
Pichler
Pichler AMELIA Manual de usuario
