Piazzetta G958 Manual de usuario

300914 PZPE.G958BODYA 5055.61-B

INSTALER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

WARNING: If the information in these

instructions is not followed exactly a fire or

explosion may result causing property

damage, personal injury or death.

FOR YOUR SAFETY

Do not store or use gasoline or other

flammable vapours and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electrical switch.

Do not use any phone in your building.

Immediately call your gas supplier

from a neighbour’s phone. Follow the

gas supplier’s instructions.

If you cannot reach your gas supplier

call the fire department.

Installation and service must be performed

by a qualified installer, service agency or the

gas supplier.

This appliance may be installed in an

aftermarket permanently located,

manufacture home (USA only) or mobile

home, where not prohibited by local codes.

This appliance is only for use with the type of

gas indicated on the rating plate. This

appliance is not convertible for use with

other gases unless a certified kit is used.

This appliance is suitable for installation in a

bedroom or bed sitting room.

G958

INSTALLATION AND

OPERATING INSTRUCTIONS

MODEL: G958

SERIES: A

DIRECT VENT GAS STOVE

Table of Contents

Caution 4

Safety 5

Owners Information

First Fire 6

Remote Control Operation 7

Maintenance 13

Lighting Instructions 14

Installer information

Fireplace Dimensions 15

Clearances to Combustibles 16

Locating the Fireplace 16

Venting 17

Plumbing and Electrical 19

Gas Supply 20

Gas Pressure Check 20

Gas Pressure Testing Procedure 21

Pilot Adjustment 21

Propane Conversion 22

Door Installation / Removal 23

Fan Installation/ Removal 23

Panel Installation/Removal 24

Burner Kit Installation/Removal 25

Glass Kit Installation 25

Log Set Installation 25

Cladding Installation/Removal 26

Venturi Adjustment 27

Replacement Parts 28

Aesthetic Options 28

Venting Components 29

Wiring Diagram 30

Installation Notes 31

FOR YOUR SAFETY - Do not install or operate your Pacific Energy gas fireplace without first

reading and understanding this manual. Any installation or operational deviation from the

following instructions voids the Pacific Energy Fireplace Products Warranty and may prove

hazardous.

This appliance and its individual shut off valve must be disconnected from gas supply piping

system during any pressure testing of that system at test pressures in excess of 1/2 psi

(3.5 kPa).

This appliance must be isolated from the gas supply piping system by closing its individual

manual shut off valve during any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 psi (3.5 kPa).

Do not use the fireplace if any part has been under water. Immediately call a qualified service

technician to inspect the fireplace and to replace any part of the control system and / or any gas

control which has been under water.

This fireplace is equipped with a micro mesh safety screen for your protection and must

be installed with the unit. Removal of the safety screen will cause the fireplace to

become a burn hazard.

Caution

Due to high temperatures, this gas appliance should be located out of traffic and away

from furniture and draperies.

Children and adults should be alerted to the hazards of high surface temperatures and

should stay away to avoid burns or clothing ignition.

Young children should be carefully supervised when they are in the same room as the

appliance. Toddlers, young children and others may be susceptible to accidental contact

burns. A physical barrier is recommended if there are at risk individuals in the house. To

restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers,

young children and other at risk individuals out of the room and away from hot surfaces.

Clothing or other flammable material should not be placed on or near the appliance.

A barrier designed for to reduce the risk of burns from the hot viewing glass is provided

with the appliance and shall be installed.

If the barrier becomes damaged, the barrier shall be replaced with the manufacturers

barrier for this appliance.

Any grill, panel or door removed for servicing the unit must be replaced prior to operating.

Installation and repair should be done by a qualified service person. The appliance should

be inspected before use and at least annually by a professional service person. More

frequent cleaning may be required due to excessive lint from carpeting, bedding material,

etc. It is imperative that control compartments, burners and circulating air passageways of

the appliance be kept clean.

This appliance must not be connected to a chimney flue serving a separate solid fuel

burning appliance.

It is our policy that no responsibility is assumed by the Company or by any of its

employees or representatives for any damages caused by an inoperable, inadequate, or

unsafe condition which is the result, either directly or indirectly, of any improper operation

or installation procedures.

Safety

OWNER’S

INFORMATION

Congratulations on your purchase of a Pacific Energy Gas Fireplace.

Your fireplace has been professionally installed by:

Dealer name: ___________________

Phone Number: _________________

If you discover any problems with your gas fireplace contact your dealer immediately to have the

unit repaired.

Caution: Do not attempt to repair the fireplace because you may cause injury to yourself or other,

and risk causing damage to the unit.

Before operating your fireplace carefully read this manual and pay close attention to all Safety

Warnings. The manual contains important information on the unit’s safe operation and

maintenance.

When lit for the first time, the fireplace will emit a slight odour for a couple of hours. This is due to

the curing of paints, sealants, gaskets, and lubricants used in the manufacturing process. This

condition is temporary. Open doors and windows to ventilate the area. Odour caused by the curing

process may cause discomfort to some individuals.

It is normal for fireplaces fabricated from steel to give off some expansion and/or contraction

noises during the start up or cool down cycle. Similar noises are found with your furnace heat

exchanger or cook stove oven.

First Fire

OWNER’S

INFORMATION

Remote Control Operation

System Description

The Proflame Remote Control System consists of two elements:

1. Proflame Transmitter.

2. Proflame Integrated Fireplace Control (IFC) board and a wiring harness to connect the IFC

to the gas valve and stepper motor.

Transmitter (Remote Control with LCD Display)

The Proflame Transmitter uses a streamline design with a simple button layout and informative

LCD display (Figure 1). The transmitter is powered by 3 AAA type batteries. A mode key is

provided to index between the features and a thermostat key is used to turn on/off or index through

thermostat functions (Figure 1 & Figure 2).

Figure 1: Proflame Transmitter

Figure 2: Transmitter LCD display

OWNER’S

INFORMATION

OPERATING PROCEDURE

Initializing the System for the first time

Install the 4 AA batteries into the battery bay. Note the polarity of the battery and insert into the

battery holder as indicated on the battery cover (+/-). Set the main ON/OFF and the CPI/IPI switch

in the closed position. Press the SW1 button on the IFC module. The IFC will “beep” three (3) times

to indicate that it is ready to synchronize with a transmitter. Install the 3 AAA type batteries in the

battery bay, located on the base of the transmitter. With the batteries already installed in the

transmitter, push the ON button. The receiver will “beep” four times to indicate the transmitter’s

command is accepted. If a second Transmitter must be registered it can be turned ON. The

receiver will beep again four (4) times and exit the synchronization phase. If only one transmitter is

used, then press the button SW1 to exit the synchronization phase.

The system is now initialized.

IFC Module

The Proflame 2 Integrated Fireplace Control (IFC) board is a device that allows the automatic

ignition and pilot flame supervision, to command the functions of a hearth appliance. It’s

configured to control the ON/OFF main burner operation, giving the choice of both IPI (intermittent

pilot ignition), and CPI (continuous pilot ignition) modes.

The Proflame 2 IFC board controls and connects directly to the pilot assembly and an automatic

valve of the Proflame 880, 886 and 885 families using low electric power.

The IFC Board can be powered by an AC and battery pack for back up (ATMO Systems only). The

Proflame 2 offers the added ability to control the comfort fan speed from OFF through six (6)

speeds, a remotely actuated auxiliary outlet and a dimmable light outlet. The external batteries can

provide DC power to the IFC allowing the batteries to be used only when line power is interrupted

or lost, and if the appliance does not use a combustion fan.

OWNER’S

INFORMATION

Temperature indication Display

With the system in the “OFF” position, press the thermostat key and the

mode key at the same time. Look at the LCD screen on the transmitter to

verify that a C or F is visible to the right of the room temperature display.

(Figure 3 & Figure 4)

Turn on the Appliance

First close the main ON/OFF switch on the wirings. With the system OFF,

press the ON/OFF Key on the transmitter. The transmitter display will show

all active icons on the screen. At the same time IFC will be commanded to

start the ignition process. Once the pilot flame is proven the IFC board will

open the main valve outlet and the appliance main burner will also ignite. A

single “beep” from the IFC module will confirm reception of the command.

Turn off the Appliance

With the system ON, press the ON/OFF key on the transmitter. The

transmitter LCD display will only show the room temperature. At the same

time the IFC will be commanded to turn off the burner. Depending on the

system mode (IPI or CPI) the pilot may shut off (IPI) or remain lit (CPI) and

the appliance burner turns OFF. A single “beep” from the receiver confirms

reception of the command.

Manual Bypass of the Remote System

If the batteries of the receiver or transmitter are low or depleted, the

appliance can be turned off manually using switch located on battery box.

This will bypass the remote control feature of the system.

Key Lock

This function will lock the keys to avoid unsupervised operation.

To activate this function, press the MODE and UP keys at the same time

(Figure 5).

To de-activate this function, press the MODE and UP keys at the same time.

Figure 5

Figure 4: Display in Celsius

Figure 3: Display in Fahrenheit

OWNER’S

INFORMATION

Remote Flame Control

The Proflame has six (6) flame levels.

With the system on, and the flame level

at the maximum in the appliance,

pressing the down arrow key once will

reduce the flame height by one step

until the flame is turned off.

The up arrow key will increase the flame

height each time it is pressed. If the up

arrow key is pressed while the system is

on but the flame is off, the flame will

come on in the high position. (Figure 6)

A single “beep” will confirm reception of

the command.

Figure 6

ROOM THERMOSTAT (Transmitter Operation)

The remote control can operate as a room thermostat. The

thermostat can be set to a desired temperature to control the

comfort level in a room.

To activate this function, press the thermostat key (Figure 1). The

LCD display on the transmitter will change to show that the room

thermostat is “ON” and the set temperature is now displayed

(Figure 7). To adjust the set point, press the up or down arrow

keys until the desired set point temperature is displayed on the

LCD screen of the transmitter.

Smart Thermostat (Transmitter Operation)

The Smart Thermostat function adjusts the flame height in

accordance to the difference between the set point and the room

temperatures. As the room temperature gets closer to the set point

the Smart Function will modulate the flame down. If the room

temperature is cool the Smart Function will modulate the flame up.

To activate this function, press the THERMOSTAT key (Figure 1)

until the word "SMART" appears to the right of the temperature

bulb graphic (Figure 8). To adjust the set point, press the up or

down arrow keys until the desired set point temperature is

displayed on the LCD screen of the transmitter (Figure 9).

Figure 7

Figure 8: Smart Flame Function

Figure 9

Tabla de contenidos

Otros manuales de Cocina de Piazzetta

Piazzetta

Piazzetta MT 361 Guía de inicio rápido

Piazzetta

Piazzetta E903 Guía

Piazzetta

Piazzetta Multifuoco 2003 Guía de inicio rápido

Piazzetta

Piazzetta P961 THERMO Manual de lista de piezas

Piazzetta

Piazzetta P965 Thermo Manual de usuario

Piazzetta

Piazzetta E44 Guía de inicio rápido

Piazzetta

Piazzetta E902 Guía de inicio rápido

Piazzetta

Piazzetta P936 Manual de usuario

Piazzetta

Piazzetta P158 Manual de usuario

Piazzetta

Piazzetta E903 Manual de lista de piezas

Piazzetta

Piazzetta P962 Manual de lista de piezas

Piazzetta

Piazzetta Vera - Vittoria Guía de inicio rápido

Piazzetta

Piazzetta 600 HT Manual de lista de piezas

Piazzetta

Piazzetta Robeys LINE Manual de usuario

Piazzetta

Piazzetta E911 Guía de inicio rápido

Piazzetta

Piazzetta P163 Manual de usuario

Piazzetta

Piazzetta Thermo P966 Manual de usuario

Piazzetta

Piazzetta P944 Manual de lista de piezas

Piazzetta

Piazzetta MARCELLA 2.0 Manual de usuario

Piazzetta

Piazzetta P963 THERMO Manual de usuario

Piazzetta

Piazzetta P163 T Manual de usuario

Piazzetta

Piazzetta P944 Manual de usuario

Piazzetta

Piazzetta E902 Guía de inicio rápido

Piazzetta

Piazzetta SAHARA Manual de usuario

Manuales populares de Cocina de otras marcas

Arada

Arada Cassette Stove Manual de usuario

Parmco

Parmco FS 600 Manual de usuario

MCZ

MCZ SUITE AIR 10 M2 Manual de usuario

HearthStone

HearthStone Stowe DV 8321 Guía de solución de problemas

Cattara

Cattara FAMILY Manual de usuario

Stanley

Stanley Argon F500 OVAL Manual de usuario

Avalon

Avalon B-VENT Manual de usuario

Nordpeis

Nordpeis Vega Manual de usuario

Exquisit

Exquisit EKC601-5 Manual de operación

Stanley

Stanley Oisin Oil MK II Manual del propietario

Thermocet

Thermocet Brookfield S/CC Manual de usuario

HASE

HASE delhi Manual de usuario

Vermont Castings

Vermont Castings Intrepid 2 Manual de usuario

Italiana Camini

Italiana Camini CLASSICA Guía de inicio rápido

Avalon

Avalon Vashon Avanti DVS FS Manual de usuario

Spartherm

Spartherm ambiente a1 Manual de usuario

Dimplex

Dimplex MCFSTV12AU Manual de usuario

Warmlite

Warmlite WL46040 Manual de usuario