Phoenix Model BULLDOG Manual de usuario
BULLDOG
Wingspan :1410 mm (55.5in)
Length : 1450 mm (57.1in)
Weight :4900gr - 5600gr
Radio :6-9 Channel/ 7 servo high torque, 1standard
Engine :1.20/ 2 stroke
1.80/ 4 stroke
Instruction Manual
KIT CONTENTS: We have organized the parts as they come out of the box for better identification during
assembly. We recommend that you regroup the parts in the same manner. This will ensure you have all of
parts required before you begin assembly.
AIR FRAME ASSEMBLIES
. (2) Wing halves with ailerons
. (1) Fuselage with canopy
. (1) Horizontal stabilizer with elevator halves
. (1) Vertical stabilizer with rudder
. (1) Cowling
. (1) Decal sheet
. (1) Instruction manual
. (2) M3 connector
. (1) Ball plastic
. (1) Ball aluminum
. (1) 3mm x 12mm screw
. (1) 6mm washer
. (1) 3mm nut
AILERON CONTROL SYSTEM
. (4) Aluminum control set
. (4) 3mm x 40mm screw
. (4) Plastic horn
. (4) M3 clevis
. (8) M3 connector
. (4) Ball plastic
. (4) Ball aluminum
. (4) 3mm x 12mm screw
. (4) 6mm washer
. (4) 3mm nut.
MOTOR MOUNT ASSEMBLY
. (2) T mount
. (4) 4mm x 25mm screws
. (4) C 4mm washer
. (4) 8mm washer
. (4) 4mm x 30mm screw
. (8) 4mm nut
. (4) C 4mm washer
. (1) 600mm metal rod
. (1) 350mm plastic tube
. (1) Connector metal
FUEL TANK
.(1) Fuel tank
. (1) Stopper
. (1) Metal clunk
MISCELLANEOUS ITEMS
. (2) Plastic screw (black)
. (8) Plastic screw (white)
. (2) Plastic washer
. (4) 2.6mm x 10mm screw
. (10) 4mm x 20mm screw
. (10) C 4mm washer
. (10) 8mm washer
. (2) 4mm nut
. (2) Aluminum holder
. (4) Servo box
. (2) Carbon rod
. (1) 50mm x 200mm yellow trim
MAIN GEAR ASSEMBLY
. (2) Main gear
. (4) 4mm x 20mm screw
. (4) C 4mm washer
. (4) 8mm washer
. (2) Wheel cover
. (2) Wheel
. (2) Axle
. (4) 4mm collar
. (4) 18mm washer
. (4) 8mm nut
. (4) 4mm x 15mm screw
. (4) 8mm washer
. (4) 4mm nut
TAIL GEAR ASSEMBLY
. (1) Tail gear
. (1) Wheel
. (2) 3mm collar
. (3) 2.6mm x 12mm screw
. (2) Plastic holder
ELEVATOR CONTROL SYSTEM
. (2) Aluminum control horn set
. (2) 3mm x 40mm screw
. (2) Plastic horn
. (2) M3 clevis
. (4) M3 connector
. (2) Ball plastic
. (2) Ball aluminum
. (2) 3mm x 12mm screw
. (2) 6mm washer
. (2) 3mm nut
RUDDER CONTROL SYSTEM
. (1) Aluminum control horn set
. (1) 3mm x 40mm screw
. (1) Plastic horn
. (1) M3 clevis
Instruction Manual BULLDOG
Instruction Manual BULLDOG
Installing the aileron servo and linkages (low wing):
1
1 2 3
4 5 6
7 8 9
10 11 12
13 14 15
2
Remove the covering from the aileron servo
box.
Remove the covering.
Using the thread and the collar as a guide.
Install the aileron servo. Tape the servo lead onto the wing. Mark the hole of the control horn onto
the bottom of the aileron.
Mark the rear of the servo box onto the wing. Remove the covering. Glue the servo box onto the wing.
Install the control horn onto the aileron. Secure the control horn. The aileron linkages.
Tape the servo lead onto the end of the
thread. Pull out the servo lead.
Remove the covering from the rear of the
aileron servo box.
Instruction Manual BULLDOG
16 17 18
19 20
21 22 23
24 25 26
27 28 29
Installing the aileron servo and linkages (high wing):
2
3
Mark the rear of the servo box onto the wing. Glue the servo box onto the wing.
Install the connector rod to the control horn.
Prepare the linkages as these picture above. Prepare the linkages as these picture above. Prepare the linkages as these picture above.
Glue the carbon rod using the C.A glue.
Remove the covering from the aileron
servo box.
Remove the covering.
Remove the covering.
Remove the covering from rear of the
servo box.
Tape the servo lead into the end of the thread.Using the thread and the collar as a guide. Install the aileron servo.
Instruction Manual BULLDOG
4
30 31 32
33 34 35
36
37 38 39
40 41
Installing the horizontal stabilizer:
3
A=A-1
A=A-1
A-1
A
Mark the hole of the control horn onto
the bottom of the aileron.
Tape the servo lead onto the wing. Install the control horn onto the aileron.
Secure the control horn.Secure the control horn.
Glue the carbon rod using the C.A glue.
Install the connector rod to the control horn.
Make the center line onto the horizontal.
Remove the covering from the rear of the
fuselage.
Make the slot from the fuselage for rudder
hinge.
Check the horizontal and the wing as shows.Insert the horizontal to the fuselage. Mark the shape of the fuselage onto the
bottom of the horizontal.
Instruction Manual BULLDOG
5
42 43
44 45 46
47 48 49
50
Installing the vertical stabilizer:
4
51 52 53
Installing the tail gear:
5
B
AA1
B1
a1
a1 = a2
a2
Glue the horizontal to the fuselage using the
epoxy glue.
Remove the covering. Check the horizontal and the wing before
it dry.
Mark the shape of the vertical onto the
horizontal.
Remove the covering from the rear of the
vertical.
Check the vertical before it dry.
Make the slot at the bottom of the rudder
for the nylon keeper.
The tail gear set.
Remove the covering from the top of
the horizontal.
Remove the covering from the top of
the horizontal. Insert the hinge into the slot. Glue the vertical to the fuselage.
Glue the vertical to the fuselage.
Install the nylon keeper and glue it by CA glue.
Instruction Manual BULLDOG
6
54 55 56
57
Installing the landing gear:
6
58 59 60
61 62 63
64
Glue the two nylon keeper by C.A glue. Install the collar to the tail gear.
The main gear set. Install the wheel to the wheel cover.
Install the tail wheel.
Secure the tail gear.
Remove the covering.
Remove the covering. Secure the cover to the landing gear.
Install the axle to the landing gear.
Install the landing gear to the fuselage.
Instruction Manual BULLDOG
7
65 66 67
68 69 70
71 72 73
74 75 76
77 78
Installing the elevator servo:
7
Remove the covering. Install the elevator servo. Remove the covering.
Secure the control horn. Install the nylon horn.
Glue the carbon rod using the C.A glue. Make the same way for the second elevator
pushrod.
The elevator linkages. Prepare the elevator linkages.
Prepare the elevator linkages. Prepare the elevator linkages.
Make the same way for the second control
horn.
Secure the control horn.
Install the connector rod to the control horn.
Instruction Manual BULLDOG
8
91 92 93
Installing the fuel tank and the engine:
9
79 80 81
82 83 84
85 86 87
88 89 90
Installing the rudder servo:
8
Remove the covering. Install the rudder servo. Remove the covering.
Prepare the rudder linkages. Prepare the rudder linkages.
Prepare the rudder linkages.
The fire wall. The engine mount. Install the engine mount to the fire wall.
Secure the control horn. Secure the control horn.
Install the nylon horn.
Secure the control horn.
Glue the carbon rod using the C.A glue.Install the connector rod to the control horn.
Instruction Manual BULLDOG
9
94 95 96
97 98 99
100 101 102
103 104 105
106 107 108
Installing the throttle servo:
10
Prepare the stopper for the tank. Install the stopper to the tank. Secure the stopper.
Install the silicone tube for the tank
(not included).
Place the fuel tank into the fuselage and secure
it by C A glue.
Insert the nylon housing and secure by
C A glue.
Attach the engine to the engine mount and
mark four holes. Drill four holes onto the engine mount. Install the throttle rod.
Install the engine and secure it. Install the muffler.
Note :The distance from the fire wall to the
washer of the engine (OS 120/2stroke) is 125mm.
Install the throttle servo. Install the metal connector to the servo arm. Secure the servo arm.
Tabla de contenidos
Otros manuales de Juguete de Phoenix Model
Phoenix Model
Phoenix Model KATANA-EP Manual de usuario
Phoenix Model
Phoenix Model P40 KITTY HAWK Manual de usuario
Phoenix Model
Phoenix Model Stinson Reliant Manual de usuario
Phoenix Model
Phoenix Model Classic Manual de usuario
Phoenix Model
Phoenix Model super constellation Manual de usuario
Phoenix Model
Phoenix Model Extra 300S Manual de usuario
Phoenix Model
Phoenix Model F4U Corsair Manual de usuario
Phoenix Model
Phoenix Model Dolphin 40 Manual de usuario
Phoenix Model
Phoenix Model Tiger 60 Manual de usuario
Phoenix Model
Phoenix Model BAE HAWK Manual de usuario
Phoenix Model
Phoenix Model MUSTANG P51 - EP Manual de usuario
Phoenix Model
Phoenix Model SENTOSA Manual de usuario
Phoenix Model
Phoenix Model Classic Manual de usuario
Phoenix Model
Phoenix Model Tiger 3 Manual de usuario
Phoenix Model
Phoenix Model Thunderbolt P47 Manual de usuario
Phoenix Model
Phoenix Model Tiger Moth Manual de usuario
Phoenix Model
Phoenix Model F4U Corsair Manual de usuario
Phoenix Model
Phoenix Model Ryan STA Manual de usuario
Phoenix Model
Phoenix Model Tiger Moth Manual de usuario
Phoenix Model
Phoenix Model CANARY Manual de usuario
