Philips 32PF1700T/96 Manual de usuario

Published by CS 0771 BU CD Customer Service Printed in the Netherlands Subject to modification EN 3122 785 17191

retrieval system or transmitted, in any form or by any means, electronic,

mechanical, photocopying, or otherwise without the prior permission of Philips.

Colour Television Chassis

IMP1.0A

H_17191_000.eps

250507

32PF1700T/96

32PFL5422/96

37PFL5422/96

42PFL5422/96

Contents Page

1 Technical Specifications, connections, and chassis

Overview 2

2 Safety Instructions, Warnigs, and Notes 13

3 Directions for Use 14

4 Mechanical Instructions 20

5 Service Modes, Error Codes, and Fault Finding 26

6Block Diagrams, Test Point Overview, and

Waveforms

Wiring Diagram 31

Block Diagram System Signal 32

Test Point Overview 33

7Circuit Diagrams, and PWB Layouts

Diagrams 35

8 Alignments 54

9 Circuit Descriptions, Abbreviation List, and IC-Data

Sheets 60

IC-Data Sheets 70

10 Spare Parts List 74

11 Revision List 77

IMP1.0A LA 2

1. Technical Data, Connections and Chassis Overview

1.1 Technical Data

Items Spec

Weight (Net) 15.14 Kg

Dimensions (W × H × D) 847.76 × 657.38 × 220 mm

LCD panel size 32"

Aspect ratio 16:9

Native resolution 1366 × 768

LCD panel brightness (typical) 500 cd/m2

LCD panel contrast ratio

(typical) 1200:1

Viewing angle

(left/right/up/down) 88°/88° /88°/88°

Response time (Gray to Gray) 8 ms

Built-in speakers 8W × 2

• Composite Video (AV) × 1 • S-Video × 1

• Component Video (Y CB/PB CR/PR) × 1

• Composite Video/S-Video audio × 1

• Component Video audio × 1

Input

• HDMI/DVI × 1

• PC D-Sub × 1

• PC audio × 1

• DVI audio × 1

Output • Stereo audio × 1 • Headset × 1

Power supply AC 100 - 240V, 50- 60 Hz

Power consumption 180W

Operating temperature 0°C~40°C (at sea level)

Storage temperature -20°C ~ 50°C (at sea level)

IMP1.0A LA 3

1.2 Connections

External terminals panel (left side view)

Connecting the PC input

Connecting the headset audio output

1. Connect the VGA D-Sub output of your

PC to the PC D-SUB terminal on the

display using a Mini D-Sub (15-pin) cable

2. Connect the audio output of your PC to

the display's PC AUDIO terminal using an

appropriate 3.5mm Mini-jack stereo audio

cable.

Note: To view video image from this input,

please select VGA as the input source.

When you connect the display to a PC,

you should adjust the resolution in the

display properties of the computer to

closely match the native resolution of the

display (for example, 1360 x 768 pixels).

Connecting the headset audio output

This display provides a stereo headset

output socket for delivering the audio

signal to a stereo headset. Connect the

stereo headset plug (3.5mm Mini-jack type)

to the stereo headset output socket on the

display using a suitable audio cable.

Once connected, the display speakers will

be muted automatically.

No. Name Description

D-SUB

Connect to the PC video

(D-Sub) output of a PC.

1 PC

AUDIO

Connect to the audio output

to match that of the D-Sub

video output on a PC.

IMP1.0A LA 4

Connecting power

1. Connect one end of the power cord to

the AC-IN power socket on the display.

2. Connect the other end of the power

cord to the power outlet. The display will

enter standby mode and the power

indicator will light up red.

Only use an appropriate power cable for

your region. Never use a power cable

which appears damaged or frayed. Never

change the plug type on a power cable. Be

aware of total loading when using

extension cords or multiple outlet power

boards.

WARNING: This display has been

engineered and manufactured with the

highest priority on safety, however,

IMPROPER HANDLING OR USE CAN

RESULT IN POTENTIAL ELECTRICAL

SHOCK OR FIRE HAZARD. Please

handle this display with care. If damaged,

unplug the power cable from the display.

Transport the display to your nearest

authorized service centre for repair.

Adjust viewing angle

This display is equipped with an

adjustable swivel base. If necessary, turn

the display screen to an appropriate angle

(max. approximately 15 degrees left and

right) for more comfortable viewing.

Installing the tuner box

Important safety precautions

Before installing the tuner box, pay

attention to the following to ensure the

safety of installation:

• Wear suitable insulation gloves to

prevent any possibilities of injuries.

• Be sure to turn the display power off and

disconnect the power cord from the power

outlet. Turn the power of the devices off

IMP1.0A LA 5

and remove all connected signal cables if

the display is connected to other devices.

• Make sure that there is sufficient space

around the display for performing the

installation. If not, it is suggested that you

move the display to a suitable place to

perform installation, and then move it back

to its original location when installation is

completed.

Installing the tuner box

1. Locate the tuner box slot on the left side

ofthe display (as shown in the illustration).

2. Remove the protective film on the tuner

box and then insert it into the slot. Pay

attention to the direction of the tuner box

when inserting.

3. Push the tuner box all the way into the

slot.

4. Use the supplied screw and a suitable

scrsewdriver to secure the tuner box on

the display.

5. Connect the cable or aerial antenna

cable to the connector on the tuner box.

Follow the instructions of "Searching and

storing channels" on page 22 to scan and

store the channels available in your area.

IMP1.0A LA 6

Making connections

Pay attention to the following when

making connections:

• Before connecting any devices, please

turn all equipment off.

• To obtain the most benefit from the

digital LCD screen, you should select the

connection method which will provide you

with the best possible signal.

• Do not pull cables out of sockets by

grasping the cable itself, as you may

damage the cable. Only ever remove

cables from sockets by grasping the plug

on the end of the cable.

• Once connected, please ensure that all

plugs are fully inserted and firmly seated.

Be aware that if incorrect connections are

made, picture quality may be adversely

affected.

Connecting the Composite Video input

Connect the Composite Video output of

your output equipment to the VIDEO and

AUDIO L/R terminals on the display using

the Composite Video cable as illustrated.

A Composite Video cable consists of three

connectors: Yellow (video), White (left

channel audio), and Red (right channel

audio). Ensure that the colors of the plugs

and terminals match when making

connection. To view video image from this

input, switch the input source to AV.

Composite Video provides the least

optimal image quality. Both S-Video and

Component Video provide better quality

video signals. AV supports both

Composite Video and SVideo signal

inputs. If you use S-Video, you cannot use

Composite Video for that input.

Connecting the S-Video input

1. Connect the S-Video output of your

output equipment to the display's

S-VIDEO terminal using an S-Video cable

(not provided). Pay attention to the

alignment of the plugs on the S-Video

cable when inserting so as not to damage

any pins.

IMP1.0A LA 7

2. Connect the corresponding audio

output of the output equipment to the

AUDIO L/R input terminals using a

suitable audio cable.

To view video image from this input,

switch the input source to AV.

You should not connect both a composite

Video and an S-Video from the same

device; just one or the other. If you have

the choice, use the S-Video instead of

composite Video as an S-video signal

provides a higher quality signal to that of

composite Video.

Connecting the Component Video input

1. Connect the S-Video output of your

output equipment to the display's

S-VIDEO terminal using an S-Video cable

(not provided). Pay attention to the

alignment of the plugs on the S-Video

cable when inserting so as not to damage

any pins. 2. Connect the corresponding

audio output of the output equipment to

the AUDIO L/R input terminals using a

suitable audio cable.

To view video image from this input,

switch the input source to AV.

You should not connect both a

composite Video and an S-Video from

the same device; just one or the other.

If you have the choice, use the S-Video

instead of composite Video as an

S-video signal provides a higher

quality signal to that of composite

Video.

1. Connect the Component Video output

of your output equipment to the display's Y,

CB/PB and CR/PR terminals using a

Component Video cable (not provided). A

Component Video cable consists of three

plugs: Green (Y), Blue (CB/PB), and Red

(CR/PR). Ensure that the colours of the

plugs and terminals match when making

connection.

2. Connect the corresponding audio

output of your output equipment to the

AUDIO L/R input terminals on the display

using an audio cable (not provided).

To view video image from this input,

switch the input source to Component.

Of the analog video signal types,

Component Video offers the best

quality.

IMP1.0A LA 8

Connecting the DVI input

1. Connect the digital video output of your

output equipment (for example, a PC or

digital Set Top Box) to the HDMI terminal

on the display using a DVI to HDMI

adaptor cable (not provided).

2. Connect the DVI audio output of your

output equipment to the display's

DVIAUDIO L/R input terminals using an

appropriate audio cable (not provided). To

view video image from this input, switch

the input source to HDMI.

When connected to a PC, you should

adjust the resolution in the display

properties of the computer to closely

match the native resolution of the display

(for example, 1360 x 768 pixels).

Connecting the HDMI input

Connect the HDMI output of your output

equipment to the HDMI terminal on the

display using an HDMI cable (not

provided). To view video image from this

input, switch the input source to HDMI.

HDMI (High-Definition Multimedia

Interface) is an uncompressed and

all-digital audio/video interface. HDMI

provides an interface between any

audio/video source, such as a set-top box,

DVD player, or A/V receiver over a single

cable. The display’s HDMI inputs are

compliant with the HDMI 1.2 standard.

However, the playback of SACD (Super

Audio CD) audio is not supported. Be

aware that HDMI input must be HDCP

compliant to be displayed. To ensure the

stability and performance of signal

transmission, it is recommended that you

IMP1.0A LA 9

use high-quality and HDMI-certified cable

for connection.

Connecting the stereo audio output

This display provides a set of stereo audio

output terminals (RCA type) for delivering

the audio signal to a sound system or

other audio devices. Connect the audio

input terminals of an amplifier or other

audio device to the AUDIO OUT L/R

terminals on the display using a suitable

audio cable.

This output is always available. Its level is

fixed and cannot be adjusted by the

Volume setting of the display.

Installing the tuner box

Before installing the tuner box, please pay

attention to the following to ensure the

safety of installation:

• Wear suitable protective insulation

gloves to prevent any possibilities of

injuries.

• Peel off the protective film on the tuner

box prior to installation.

• Be sure to turn the display power off and

disconnect the power cord from the power

outlet. Turn the power of the devices off

and remove all connected signal cables if

the display is connected to other devices.

• Make sure that there is sufficient space

around the display for performing the

installation. If not, it is suggested that you

move the display to a suitable place to

perform installation, and then move it back

to its original location when installation is

IMP1.0A LA 10

completed.

1. Turn the display to reveal its left side

and locate the tuner box slot (as shown in

the illustration on the right).

2. Use a suitable screwdriver to remove

the screw that secures the tuner box slot

cover.

3. Remove the tuner box slot cover as

shown.

4. Peel off the protective film on the tuner

box and then insert the tuner box into the

slot as shown. Pay attention to the

direction of the tuner box when inserting.

5. Push the tuner box all the way into the

slot.

6. Use the supplied screw and a suitable

screwdriver to secure the tuner box on the

display.

7. There are two connectors on the tuner

box: one for aerial antenna input and the

Otros manuales para 32PF1700T/96

Este manual sirve para los siguientes modelos

Otros manuales de TELEVISOR de Philips

Philips

Philips 22PFL2908H/12 Manual de usuario

Philips

Philips MAGNAVOX PR1912B Manual de usuario

Philips

Philips 29PT8304 Manual de usuario

Philips

Philips 775 Manual de usuario

Philips

Philips 7202 Series Manual de usuario

Philips

Philips Econova 46PFL6806T/12 Manual de usuario

Philips

Philips 32PFL3168H Manual de usuario

Philips

Philips MAGNAVOX TS3258 Manual de usuario

Philips

Philips 29PT9221/93 Manual de usuario

Philips

Philips TP2797B Manual de usuario

Philips

Philips Q552.2L Manual de usuario

Philips

Philips T260XW02V400 Manual de usuario

Philips

Philips L9.2EAA Manual de usuario

Philips

Philips 28PT7304 Manual de usuario

Philips

Philips 19PFL5522D Manual de usuario

Philips

Philips 8P4841C Manual de usuario

Philips

Philips 42PFL3604/12 Manual de usuario

Philips

Philips 37PFL3403/93 Manual de usuario

Philips

Philips 14PT2321 Manual de usuario

Philips

Philips 65HFL2859T/12 Manual de usuario

Philips

Philips 21PT2327/V7 Manual de usuario

Philips

Philips M-Link 27PT71B1 Manual de usuario

Philips

Philips 42PF7220A/37B Manual de usuario

Philips

Philips PUS7855 Manual de usuario

Manuales populares de TELEVISOR de otras marcas

Toshiba

Toshiba 27A10 Manual de usuario

Hitachi

Hitachi 32FX48B Manual de usuario

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Manual de usuario

Changhong Electric

Changhong Electric uhd55b6000is Manual de usuario

Panasonic

Panasonic Genus TX-G10 Manual de usuario

Toshiba

Toshiba 19A20 Manual de usuario

Sony

Sony XBR-100Z9D Manual de usuario

Samsung

Samsung 55S9 B Series Manual de usuario

Sharp

Sharp LC-40FI5012E Manual de usuario

Loewe

Loewe Table Stand Reference 55 Manual de usuario

Sylvania

Sylvania 6427FB Manual de usuario

Sanyo

Sanyo CE19LD90N-B Manual de usuario

North State

North State TV2GO Manual de usuario

RCA

RCA RTU7877 Manual de usuario

Sharp

Sharp 21K-FG1RU Manual de usuario

Sony

Sony Esprit TAV-L1 Manual de usuario

Grundig

Grundig 43 VLE 4820 Manual de usuario

Samsung

Samsung LN26C350D1D Manual de usuario