Philips SRU5130/53 Manual de usuario

SRU 5130/87

EN Remote control 3

IT Telecomando 12

ES Mando a distancia 22

PT Telecomando 32

∆ËÏÂ¯ÂÈÚÈÛÙ‹ÚÈÔ

TR Uzaktan kumanda 51

RU пульта ДУ 60

PL Pilota 70

CS Dálkového ovládání 79

and get support at

www.philips.com/welcome

Universal remote control

Table of contents

1 Your universal remote control 3

2 Installing the remote control 3-6

2.1 Inserting the batteries 3

2.2 Testing the remote control 4

2.3 Setting the remote control 4-6

3 Keys and functions 7-8

4 Extra possibilities 8-9

4.1 Adjusting device selection (Mode keys) 8-9

4.2 Restoring the original remote control settings 9

5 Frequently asked questions 10

6 Need help? 11

Code list of all brands / equipment 89-102

Information to the Consumer 104

1 Your universal remote control

Congratulations on your purchase and welcome to Philips.

To fully benefit from the support that Philips offers, register your product

at www:philips.com/welcome.

For quick, clean and easy setup go to: www.philips.com/urc

After installing the universal remote control SRU 5130 you can operate a

maximum of 3 different devices with it:TV, Set Top Box (satellite or cable

decoder, digital terrestrial television), DVD player/HDD/recorder or VCR.

2 Installing the remote control

2.1 Inserting the batteries

Press the cover inwards and slide it in the direction of the arrow.

Place two AAA type batteries into the battery compartment, as

shown.

Replace the cover and click it firmly into place.

3Installing the remote control

ENGLISH

2.2 Testing the remote control

The remote control has been programmed to operate most Philips

devices. Because the SRU 5130 may use different signals for each brand

and even for different models of the same brand, it is advisable to test

whether your device responds to the SRU 5130.The example below (TV)

instructs you how to do this.You can repeat the same steps for other

devices (Set Top Box, DVD player/recorder orVCR) which you want to

operate using the SRU 5130.

Example of TV:

Turn your TV on manually or use the original remote control.Tune to

channel 1.

Press the TV key to select TV.

• The key lights up.

• If the key does not light up, check whether the batteries are

properly inserted (see ‘2.1 Inserting the batteries’).

Check whether all the keys are working.

For an overview of the keys and their functions see

‘3. Keys and functions’.

• If the TV responds as it should to all of the key commands the SRU 5130

is ready for use.

Tip

If the device does not respond at all or not to all of the key commands,

follow the instructions under ‘2.3 Setting the remote control’, or for online

setup go to: www.philips.com/urc.

2.3 Setting the remote control

This is only necessary if your device does not respond to the SRU 5130.

If that is the case, the SRU 5130 does not recognize the brand and/or

model of your device and you need to program the remote control to do

so.The example below (TV) instructs you how to do this.

You can repeat the same steps for other devices (Set Top Box, DVD

player/ recorder orVCR) which you want to operate using the SRU 5130.

4Installing the remote control

ENGLISH

5Installing the remote control

Example of TV:

Turn on the TV manually or use the original remote control.Tune in

to channel 1.

Look up the brand of your TV in the code list at the back of this

manual.A four-figure code is shown for each brand.

Note the code for your brand.

Be careful! There are separate tables for TV, STB, DVD

and VCR.

Make sure you use the codes from the correct table.

Press the TV key until it flashes twice and then

remains lit.

Then enter the code noted in step 2 using the numeric keys.

• The TV key now flashes twice.

•If the key flashes once for an extended period, the code has not

been entered properly or the wrong code has been entered. Start

again from step 2.

Press and hold the Stand-by key of the SRU 5130 until your TV

switches off (stand-by).

Then release the key immediately.

• The SRU 5130 is now set to operate your TV.

Check if you can operate all functions on your TV with the SRU 5130.

• If a key does not function properly, keep it pressed until it works.

Then release the key immediately.

Repeat this for every key that does not work.

• If the TV responds to all of the key commands, the

SRU 5130 is ready for use. Do not forget to note your code.

Keep the TV key pressed for 5 seconds to exit setup mode.

• When no key is pressed for 2 minutes or more the remote control will

exit setup mode automatically.

When setting the remote control for other devices, be sure to enter

and exit setup mode with the appropriate mode key. STB for Set Top

Box, satellite or cable decoder and digital terrestrial television and

DVD for DVD player/ recorder andVCR.

Full search setup

If your code does not work or if the brand of your device is not

mentioned in the code list, you can try setting the remote control with

full search setup.

Press the mode key of the device you wish to set up the remote

control for. E.g. the TV key.

Press the key until it flashes twice and then remains lit.

Press and hold the Stand-by key of the SRU 5130 until your TV

switches off (stand-by).

Then release the key immediately.

• The SRU 5130 is now set to operate your TV.

Full search setup takes about 5 minutes.

Installing the remote control

ENGLISH

Keys and functions

3 Keys and functions

The illustration on page 2 gives an overview of all keys and their

functions.

1yStand-by switches TV, STB or DVD on or off.

2/ DISC • Text TV on/off (TV).

• disc menu (DVD).

/ FAV(orites) • Electronic Program Guide (TV, STB).

• list of favorite channels (STB).

/ HDD • wide screen TV (TV).

• Hard Disk Drive menu (DVD-R).

/ LIVE • Text TV off (TV).

• live program on currently selected channel (TV,

Radio).

3 Text TV color keys. Used in text mode and in

some on-screen menus.

4 MENU turns the menu on and off.

5 Cursor keys cursor up, down, left, right in a menu.

6 INFO displays on-screen channel information (TV, STB).

7smutes the TV sound.

8 - VOL + adjusts the TV volume.

9 Numeric keys direct choice of channels and other functions.

10 A/V switches between external inputs of your

equipment.

11 5/ PICTURE • rewind (DVD/VCR).

• changes picture/screen settings (TV).

2/ AUDIO • play (DVD/VCR).

• changes audio settings (TV).

6/ ENLARGE • wind (DVD/VCR).

• enlarges Text TV picture (TV).

9/ SUBTITLE • stop (DVD/VCR).

• changes subtitle settings (TV).

0record (DVD/VCR).

;/ HOLD • pause (DVD/VCR).

• holds current Text TV page (TV).

12 /selects between one- and two-figure channel

numbers (TV, STB).

13 P1P / HOME • selects previous programme /

channel (TV, STB).

• home (STB).

• title, chapter (DVD).

14 -PROG + / KJ • selects a previous or following channel (TV, STB).

• selects a previous or following track (DVD).

15 OK confirms your selection.

16 BACK jumps back one level in the menu or turns off the

menu.

17 TV / STB / DVD device mode selection keys:

• select TV, STB or DVD mode.

• blink when the remote control is set up for the

selected device.

• light up when a remote control command is sent

to the selected device.

Note

If the device does not respond at all, or not to all of the key commands,

follow the instructions under ‘2.3 Setting the remote control’.

4 Extra possibilities

4.1 Adjusting device selection (Mode keys)

The SRU 5130 is default set for operating TV, STB or DVD.You can select

the device you wish to operate with the TV, STB and DVD keys. Each

mode key allows operation of one device only. If desired, you can

program the keys to select a different kind of device. For example, if you

want to operate a second TV. In the following example you will see how

to configure the DVD key for a second TV.

Switch on the second TV.

Press the DVD key to select DVD.

• The key lights up.

Then keep keys 1 and 6 on the SRU 5130 pressed simultaneously for

three seconds, until the DVD key

lights up.

8Extra possibilities

ENGLISH

Extra possibilities

Press keys 9, 9 and 2 in that order.

Press the TV key to select TV.

Press the key until it flashes twice and then remains lit.

• The DVD key flashes twice.

The DVD key will now allow you to operate your second TV.

Program the SRU 5130 to operate the second TV.

See ‘2.3 Setting the remote control’.

4.2 Restoring the original functions of your remote control

Keep keys 1 and 6 on the SRU 5130 pressed simultaneously for three

seconds, until one of the

mode keys (TV, STB or DVD) flashes twice and then remains lit.

Press keys 9, 8 and 1, in that order.

• The mode key (TV, STB or DVD) flashes twice.

All original functions have now been restored and any extra functions

have been deleted.

10 Frequently asked questions

ENGLISH

5 Frequently asked questions

In this chapter you find answers to the most frequently asked questions

about your universal remote control.

How do I set the remote control for combo devices (TV/VCR,

TV/DVD, DVD/VCR, etc)?

Some combo devices require you to set up two different source selection

keys to control both parts of the combo device. For example, if you have

a TV/DVD combo, you might need to set up one code under the TV key

to control the TV and a separate code under the DVD key to control the

DVD.

The device I want to operate does not respond and the mode

key (TV, STB or DVD) does not flash when I press a key.

Replace the old batteries with two new AAA batteries.

The device I want to operate does not respond but the mode

key (TV, STB or DVD) does flash when a key is pressed.

Point the SRU 5130 at the device and make sure that there are no

obstructions between the SRU 5130 and the device.

The SRU 5130 does not respond properly to commands.

Try programming the SRU 5130 again.

If the device still does not respond, call our helpline.

The Text TV keys do not work.

• Find out whether your TV is equipped with Text TV.

• Maybe the SRU 5130 has to be adapted to the model of the device.

Call our helpline for details.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Mando a distancia de Philips

Philips

Philips SRP6220R/27 Manual de usuario

Philips

Philips SRP3011 Manual de usuario

Philips

Philips SRU 5170/86 Manual de usuario

Philips

Philips SBCRU631/00 Manual de usuario

Philips

Philips PM8TSMD Manual de usuario

Philips

Philips SBC RU 530/87U Manual de usuario

Philips

Philips SRU740NC Manual de usuario

Philips

Philips SBC RU422 Manual de usuario

Philips

Philips 22AV1125 Manual de usuario

Philips

Philips SRP 3004/10 Manual de usuario

Philips

Philips SBCRU410 Manual de usuario

Philips

Philips 29PT9413/12 Manual de usuario

Philips

Philips ProntoTSU9800 Manual de usuario

Philips

Philips SRU 3040/10 Manual de usuario

Philips

Philips SRU1020/10 Manual de usuario

Philips

Philips PMDVR8 Manual de usuario

Philips

Philips T32 Manual de usuario

Philips

Philips KWR174002/01BRS Manual de usuario

Philips

Philips Perfect replacement SRP5107 Manual de usuario

Philips

Philips MELICONI Manual de usuario

Philips

Philips SRP2008B/86 Manual de usuario

Philips

Philips Prestigo SRU8015 Manual de usuario

Philips

Philips KWR164501/01 Manual de usuario

Philips

Philips 22AV8573 Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación