Philips SRP3219G/27 Manual de usuario

User manual

Audio/Video

SRP3219G/27

v1 12/19

SRP3229G/27

SRP3239R/27

SRP3249B/27

Introduction ............................................................. 2

Setup......................................................................... 3

Button Functions ....................................................4

Programming Your Remote ...................................6

Direct Code Entry ..............................................6

Auto Code Search.............................................. 7

Controlling Combo Devices .............................9

Using Your Remote ............................................... 10

Code Identication.......................................... 10

Reset to Factory Settings............................... 10

Primary Audio Control..................................... 11

Troubleshooting................................................12

Warranty..................................................................13

FCC Statement ...................................................... 14

Congratulations on your purchase of this Philips

branded Universal Remote Control. This remote

is capable of operating thousands of audio/

video devices including TVs, Blu-ray™/DVD

players, streaming media players, sound bars,

cable receivers and more!

Table of Contents

SAVE THIS MANUAL AND CODE LIST

FOR FUTURE REFERENCE

https://byjasco.com/urccodes

Your universal remote requires two (2) AAA

batteries (not included). Alkaline batteries are

recommended.

Battery Installation

1. On the back of the remote, pull down on

the textured surface and slide battery cover

downward to remove.

2. Match the (+) and (-) marks on the batteries

to the (+) and (-) marks inside the battery

compartment, then insert two (2) AAA

batteries. Be sure to use fresh batteries.

3. Position battery cover slightly below opening

and push upward to lock into place.

NOTE:If your remote stops operating properly,

replace the batteries with new ones.

Battery Precautions

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-

zinc), or rechargeable (Ni-Cd, Ni-MH, etc.)

batteries.

• Always remove old, weak or worn-out

batteries promptly and recycle or dispose of

them in accordance with local and national

regulations.

Battery Saver

Your remote automatically turns o if the

buttons are depressed more than 8 seconds.

This will save your batteries should your remote

get stuck in a place where the buttons remain

depressed (e.g., between the sofa cushions).

Code Saver

You have up to 10 minutes to change the

batteries in your remote without losing the

codes you have programmed.

Setup

9 9

11 11

Button Functions

1. Power - Turns devices ON/OFF

2. TV, STR, AUD - Selects the device to control

3. Info/Options - Displays on-screen show/

content information

4. Exit -Exit on-screen menus

5. Record, play, stop, rewind, fast

forward, pause

6. DVD/Blu-ray™open/close - open/close a

player, or List features on cable/satellite

receivers

7. Up/down/left/right menu navigation

8. Last channel - Returns to the previously

selected channel

9. Channel up/down

10. ABCD - Access additional features for DVRs,

cable and satellite receivers

11. Numbers - Enter numbers for direct

channel selection

12. Dash (-) - Use to select digital channels,

e.g., 4.1

13. Enter key (Some devices require enter to

be pressed after channel selection)

14. Volume up/down

15. Mute - Mutes sound

16. Ok - Selects menu items for the

controlled device

17. Setup - Used to program the remote

18. Streaming App Hotkey - Access top apps

like Netix®, Amazon®Prime, Hulu®and more

19. Home/Guide - Easily access features on

today’s streaming devices, or Guide on

cable/satellite receivers

20. Menu - Displays the on-screen menu

21. Input - Selects video inputs

Programming Your Remote

Your remote is designed to control multiple

audio/video devices. To use, you will need to

program the remote for your devices. There

are two dierent methods you can use to

program the remote, Direct Code Entry or

Auto Code Search.

• The Direct Code Entry method is the

recommended method as it is the simplest

and quickest method in most cases.

• The Auto Code Search method searches

through all the codes in the remote to nd a

code for your device.

NOTE:This remote comes preprogrammed for

Roku®boxes and Samsung TVs. Press TV for

Samsung TVs and STR for Roku boxes.

Direct Code Entry (Recommended)

1. Locate the Code List included

with your remote. Find the section

for the type of device you wish to

control, (for example TV, STR, AUD).

Locate the brand of your device

and circle all the remote codes for

the brand.

2. Press and hold down the SETUP

button on the remote until the red

light on the remote control turns

on. Release the SETUP button.

The red light will remain on.

NOTE:The red light will either be a

small light at the top of the remote

or the power ON/OFF button.

3. Press and release the device

button on the remote for the type

of device you wish to control, (for

example TV, STR, AUD). The red

light will blink once and remain on.

NOTE:Any of the device buttons

on the remote can be programmed

to control any of your devices. For

example, you can use the aux device

button on the remote to control a

Satellite Receiver, Digital Converter

Box, Streaming Media Player or any

device category in the Code List.

Programming Your Remote

4. Use the number buttons on the

remote to enter the rst 4-digit

remote code you circled in the

Code List in Step 1. The red light

will turn o after entering the

fourth digit.

5. Point the remote at the device.

Test the buttons on the remote

to see if the device responds as

you would expect. If the buttons

do not operate the device, return

to Step 2 above and use the next

code that you circled for that

device.

6. Repeat steps 1 – 5 for each

device you wish to control.

Programming Notes

• Some codes may operate only a few

functions of your device. There may be

another code in the Code List that controls

more functions. Test other codes in the

Code List for more functionality.

• If you do not nd a remote code that works

your device or there are no codes in the

Code List for your device, use the Auto

Code Search method in the next section to

program your remote.

• For combination devices such as a TV/DVD

combo or TV/VCR combo, you may have to

enter a code for each device.

• Write down the remote codes used to

program the remote for future reference.

Auto Code Search

The Auto Code Search is a process where you

can search through all the codes stored in

the remote to nd a code for your device. It is

recommended that you read through all the

steps below to familiarize yourself with the

Auto Code Search before starting the process.

Programming Your Remote

1. Manually turn on the device you

wish to control.

NOTE:The Auto Code Search process

cannot be used for devices without

power ON/OFF capability. Use the

Direct Code Entry method in these

cases.

2. Press and hold down the SETUP

button on the remote until the red

light on the remote control turns on.

Release the SETUP button. The red

light will remain on.

NOTE:The red light will either be a

small light at the top of the remote or

the power ON/OFF button.

3. Press and release the device button

on the remote for the type of device

you wish to control, (for example TV,

STRM, AUX). The red light will blink

once and remain on.

4. With the remote pointed at the

device, press and release the

POWER button on the remote. The

remote will send 10 dierent codes

to the device. The red light will blink

once for each code and remain on

after sending the 10 codes.

Did the device turn o?

• If YES, go to Step 5.

• If NO, repeat Step 4 to test the

next 10 codes.

5. Manually turn the device back on.

6. With the remote pointed at the

device, press and release the

VOL button. The remote will re-

send the rst code of the 10 codes

from Step 4. The red light will blink

once and remain on.

Did the device turn o?

• If YES, you have found a code for

the device. Press and release the

same device button you pressed

in Step 3. This will store the code

in the remote. Go to Step 7.

Programming Your Remote

• If NO, continue to press and

release the VOL button until

the device turns o to test the

other 9 codes from Step 4. Be

sure to wait approximately

3 seconds after each VOL

button press to allow the device

time to respond to the code.

When the device turns o, you

have found a code for your

device. Press and release the

same device button pressed in

Step 3. This will store the code

in the remote. Go to Step 7.

NOTE:

• The VOL button can be used to

go backwards through each batch

of 10 codes.

• The red indicator light will ash 2

times after testing the rst or last

code in each batch of 10.

7. Use the remote to turn the device

back on. Test the buttons on

the remote to see if the device

responds as you would expect.

If the buttons do not operate the

device, return to Step 2 and repeat

this process to search for a better

code to operate the device.

8. Repeat this process for each

device you wish to control.

Controlling Combo Devices

Some combo devices (e.g. TV/VCR, TV/DVD,

DVD/VCR, etc.) will require you to set up two

dierent device buttons to control both parts

of the combo device. For example, if you have

a TV/DVD combo, you may need to set up one

code under the TV button to control the TV

and a separate code under the DVD button to

control the DVD.

Using Your Remote

1. Press and hold down the SETUP

button on the remote until the

red light on the remote control

turns on. Release the SETUP

button. The red light will

remain on.

2. Press and release the desired

device button (TV, STRM, AUD)

you would like the code for.

3. Press and release the

ENTER button.

4. Press and release the #1 button.

Count the number of times the

remote light ashes. This is the

number corresponding to the

rst digit of the code. Repeat the

process by pressing the #2, #3

and #4 buttons for the remaining

digits.

5. Press and release the ENTER

button to exit this mode.

Code Identication

Reset to Factory Settings

1. Press and hold down the SETUP

button on the remote until the

red light on the remote control turns

on. Release the SETUP button. The

red light will remain on.

2. Press and release the

MUTE button.

3. Press and release the number #0

button. The red indicator light will

ash twice.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Mando a distancia de Philips

Philips

Philips SRU5130/87 Manual de usuario

Philips

Philips SRP2006/55 Manual de usuario

Philips

Philips SRP4010 Manual de usuario

Philips

Philips SRP5004/53 Manual de usuario

Philips

Philips SBCRU530/00B Manual de usuario

Philips

Philips MC-110 Manual de usuario

Philips

Philips SRU5110/87 Manual de usuario

Philips

Philips SRC2063/27 Manual de usuario

Philips

Philips SBCRU410 Manual de usuario

Philips

Philips Perfect replacement SRP5107/27 Manual de usuario

Philips

Philips MELICONI Manual de usuario

Philips

Philips Home Power SPC1241AT/27 Manual de usuario

Philips

Philips SRC3036 Manual de usuario

Philips

Philips PPA1002 Manual de usuario

Philips

Philips SRP6219G/27 Manual de usuario

Philips

Philips SBC RU 252 Manual de usuario

Philips

Philips SRP6013 Manual de usuario

Philips

Philips SRU 4010/10 Manual de usuario

Philips

Philips Pronto SBCRU960/00 Manual de usuario

Philips

Philips Trilingual Front CoverArt PHBIG3 Manual de usuario

Philips

Philips SRU 560/86 Manual de usuario

Philips

Philips Head Hall C13 Manual de usuario

Philips

Philips SRP6011 Manual de usuario

Philips

Philips SBCRU641/87 Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación