Philips Showline SL eSTROBE 130 Manual de usuario

SL eSTROBE 130 LED Luminaire

Sh wline

SL eSTROBE 130 User’s Manual

www.Philips.com/Showline

24-004-3590-00 Rev1.0

SL eSTROBE 130 LED Luminaire installation & User’s Manual

The material in this manual is for information purposes only and is subject to change without notice. Showline

assumes no responsibility for any errors or omissions which may appear in this manual. For comments and

suggestions regarding corrections and/or updates to this manual, please visit the Showline website at

or contact your nearest Showline office. www.philips.com/showline

Note: Information contained in this document may not be duplicated in full or in part by any person without prior written

approval of Showline. Its sole purpose is to provide the user with conceptual information on the equipment mentioned. The use of

this document for all other purposes is specifically prohibited.

Installation & User’s Manual

SL eSTROBE 130 LED Luminaire

Additional Resources for DMX512

For more information on installing DMX512 control systems, the following publication is available for purchase

from the United States Institute for Theatre Technology (USITT), "Recommended Practice for DMX512: A Guide

for Users and Installers, 2nd edition" (ISBN: 9780955703522). USITT Contact Information:

USITT

315 South Crouse Avenue, Suite 200

Syracuse, NY 13210-1844

Phone: 1.800.938.7488 or 1.315.463.6463

www.usitt.org

Showline Limited Two-Year Warranty

Showline offers a two-year limited warranty of its luminaires against defects in materials or workmanship from the

date of delivery. A copy of Showline two-year limited warranty containing specific terms and conditions can be

obtained by contacting your local Showline office.

Warnings and Notices

When using electrical equipment, basic safety precautions should always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

Do not use outdoors.

Do not mount near gas or electric heaters.

Equipment should be mounted in locations and at heights where it will not readily be subject

to tampering by unauthorized personnel.

The use of accessory equipment not recommended by the manufacturer may cause an unsafe

condition.

Do not use this equipment for other than intended use.

Refer service to qualified personnel.

WARNING: You must have access to a mains circuit breaker or other power disconnect device

before installing any wiring. BE sure that power is disconnected by removing fuses or turning the

mains circuit breaker off before installation. Installing the device with power on may expose you

to dangerous voltages and damage the device. A qualified electrician must perform this installation.

WARNING: Refer to National Electrical Code and local codes for cable specifications.

Failure to use proper cable can result in damage to equipment or danger to personnel.

WARNING: This equipment is intended for installation in accordance with the Nation Electric

Code and local regulations. It is also intended for installation in indoor applications only. Before

any electrical work is performed, disconnect power at the circuit breaker or remove the fuse to

avoid shock or damage to the control. It is recommended that a qualified electrician perform this

installation.

TABLE OF CONTENTS

Showline Offices Inside Front Cover

IMPORTANT INFORMATION

Warnings and Notices

Additional Resources for DMX512

Showline Limited Two-Year Warranty

TABLE OF CONTENTS

PREFACE

About this Manual

Included Items

SL eSTROBE 130 LED LUMINAIRE OVERVIEW

SL eSTROBE 130 LED Luminaire Components

Common Luminaire Components

LCD Display / Menu System

INSTALLATION AND SET UP

Power Requirements

Connecting Power

Floor Mounting

Truss Mounting

SL eSTROBE 130 LED Luminaire

Connecting to the DMX512 Network

Mounting Luminaire

OPERATION AND PROGRAMMING

LCD Display and Menu System

LCD Display and Menu System Operation

SL eSTROBE 130 LED Luminaire Menu Tree

Dimming Curve Selection

Master / Slave Operational Mode

DMX CONTROL

RDM PARAMETER IDs

Single Channel Mode

Three Channel Mode

Four Channel Mode

16-Bit Mode

Zone Mapping Mode

Strobe Rate

Strobe During

SL eSTROBE 130 LED Luminaire DMX Mapping

SL eSTROBE 130 LED Luminaire RDM Parameter IDs

CLEANING AND CARE

Special Cleaning and Care Instructions

Front Lens Cleaning

Service and Maintenance

Accessories

TECHNICAL SPECIFICATIONS

Operational Specifications

Luminaire Dimensions

Table of contents

Installation & User’s Manual SL eSTROBE 130 LED Luminaire

PREFACE

1. About this Manual

The document provides installation and operation instructions for the following products:

Please read all instructions before installing or using this product. Retain this manual for future reference.

Additional product information and descriptions may be found on the product specification sheet.

Note: The SL eSTROBE 130 LED Luminaire is universal voltage 100 to 240 VAC (auto-ranging).

2. Included Items

Each SL eSTROBE 130 LED Luminaire includes the following items:

SL eSTROBE 130 LED Luminaire

SL 130 LED LuminaireeSTROBE

Installation and User’s Manual (this document)

About this Manual

AC Power Input Cable

Installation & User’s Manual

SL eSTROBE 130 LED Luminaire

SL eSTROBE 130 LED Luminaire Overview

1. SL eSTROBE 130 LED Luminaire Components

Common Luminaire Components

Figure 1: SL eSTROBE 130 LED Luminaire Components

Front of Unit Rear of Unit

DMX512-A /

LCD Display /

High Intensity LED Array

Yoke Assembly

DMX512-A /

Accessory Holder

Yoke (Tilt) Position

Locking Handle

Truss Hook / Clamp

Attachment Point

Accessory Holder Clip

RDM Input RDM THRU

Menu System AC Power Input

Installation & User’s Manual SL eSTROBE 130 LED Luminaire

LCD Display/Menu System

LCD Display / Menu System

Note: For Menu operation and programming details, refer to the "LCD Display and Menu System” on page 8.

Figure 2: LCD Display & Menu System

LEFT Arrow Button RIGHT Arrow Button

ENTER(OK) Button

EXIT Button

LCD Display

Installation & User’s Manual

SL eSTROBE 130 LED Luminaire

Installation and Set up

INSTALLATION AND SET UP

1. Power Requirements

The SL eSTROBE 130 LED Luminaire operates on AC input voltages from 100 to 240 VAC.

WARNING! This luminaire does not contain an ON/OFF switch. Always disconnect power input cable to completely

remove power from the luminaire when not in use.

AC Power Operation

When connected to an AC source, the luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The

luminaire contains an auto-ranging power supply. Each luminaire can draw up to 130 Watts.

Table 1: SL eSTROBE 130Voltage (VAC) vs. Current

2. Connecting Power

Direct connection to a AC power source using an AC input cable.

Voltage (AC)Total Current (A)Voltage (AC)Total Current (A)

0.54

0.56

0.59

0.62

0.65

0.68

0.72

240

3. Connecting to the DMX 512 Network

Basic DMX512 installation consists of connecting multiple SL eSTROBE 130 LED Luminaires together (up to 32

luminaires) the control console (or DMX512 control source) to the DMX in "daisy-chain" fashion. A cable runs from

connector on the connector on first SL eSTROBE 130 LED Luminaire. Another cable runs from the other DMX

on the next SL eSTROBE 130 LED Luminaire (or DMX512 the first Luminaire to a DMX connector device to be controlled).

Luminaire

Rear of Unit

DMX512-A / RDM DMX512-A / RDM

Input Connector THRU Connector

Figure 3: SL eSTROBE 130 LED Luminaire DMX512 Input / THRU Connections

Installation & User’s Manual SL eSTROBE 130 LED Luminaire

100 180

1.30

110 1901.18

160 0.81

150 230

0.86

140 220

0.92

130 210

1.00

120 200

1.08

170 0.76

Mounting Luminaire 7

Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on

page 1. For SL eSTROBE 130 LED Luminaire DMX Mapping, refer to "DMX CONTROL" on page 13.

Figure 4: SL eSTROBE 130 LED Luminaire - DMX512 Connections

DMX512 (out to the next luminaire or

DMX512 controlled device)

DMX512

DMX512 (out from first

to second luminaire)

DMX512 Connections

Note: Remaining pins on each connector are not used.

DMX512 Signal XLR Pin

Common (Drain) 1

DMX512 - 2

DMX512 + 3

(from console or

control device)

4. Mounting Luminaire

Floor Mounting

The SL eSTROBE 130 LED Luminaire is designed to sit directly on its yoke assembly in a floor installation application.

When used in this type of application, loosen the locking handle securing the inner portion of the yoke assembly and

separate out Figure 5). Be sure to leave enough space around the luminaire to allow proper,

uninterrupted airflow for cooling.

(as shown in

Figure 5: Floor Mounting

Figure 6: Truss Mounting

Yoke Assembly

Inner Portion (Stand)

of Yoke Assembly

Installation & User’s Manual

SL eSTROBE 130 LED Luminaire

Truss / Hanging Applications

The SL eSTROBE 130 LED Luminaire is provided with the ability to hang via truss hooks, clamps, etc. (soldseparately).

Simply attach hook, clamp, etc. to the SL eSTROBE 130 LED Luminaire enclosure assembly in the provided M10

holes. It is recommended (and may be required by local and national safety codes) to use and install a safety cable

(sold separately) as illustrated in Figure 6. When hanging the fixture, be sure to leave enough space around the luminaire

to allow proper, uninterrupted airflow for cooling and positioning. Refer to for"Luminaire Dimensions" on page 34

spacing (dimensional) requirements.

OPERATION AND PROGRAMMING

Figure 7: LCD Display and Menu System

OPERATION AND PROGRAMMING

1. LCD Display and Menu System

SL eSTROBE 130 LED Luminaires

The SL eSTROBE 130 LED Luminaire’s LCD Display and Menu System provides local control for accessing the

following fixture’s settings:

Presets (Standard and User Defined)

Chase

Settings

Status

Note: If there are multiple luminaires in a system, changes would need to be made at each LCD Menu as desired. For

the SL eSTROBE 130 LED Luminaire menu structure, see "SL eSTROBE 130 LED Luminaire Menu Tree" on page 10.

LEFT Arrow Button RIGHT Arrow Button

ENTER Button

EXIT Button

LCD Display

2. LCD Display and Menu System Operation

To navigate and access the menu settings/selections:

Step 1.Make sure the luminaire is powered and turned on.

Step 2.Press the desired button to access the menu categories.

Step 3. Use the “ ” and “ ” arrow buttons to navigate through the various options and settings.

Step 4.Make changes as desired.

Press the OK button to accept changes.

Upon power up, the LCD will display the main screen display menu of SL eSTROBE 130 LED Luminaire.

Press “ ” or “ ” to select then press 'OK' to enter.

The LCD Display Menu system consists of several categories. Upon power up, the LCD will display the main menu

automatically. desired menu item is reached, press the OK button to display the menu options, and to navigate When the

and configure the menu options as required.

Installation & User’s Manual SL eSTROBE 130 LED Luminaire

Tabla de contenidos

Otros manuales de Equipo de iluminación de Philips

Philips

Philips eW Flex Compact Manual de usuario

Philips

Philips 56459-17-16 Manual de usuario

Philips

Philips hue Adore Manual de usuario

Philips

Philips RC095V Manual de usuario

Philips

Philips 31608-48-16 Manual de usuario

Philips

Philips bodine B30 Manual de usuario

Philips

Philips CityTouch OLC NEMA SR LLC7280 Manual de usuario

Philips

Philips 910503700745 Manual de usuario

Philips

Philips TrueLine SM530C Manual de usuario

Philips

Philips Ledalite Centris Wall Mount Joint 950 Manual de usuario

Philips

Philips hue Lightstrip Plus Manual de usuario

Philips

Philips LEDALITE TruGroove Series Manual de usuario

Philips

Philips Lightolier SQ6-3 Manual de usuario

Philips

Philips Vari-Lite Manual de usuario

Philips

Philips VU6 Instrucciones de instalación

Philips

Philips Light System Manager Manual de usuario

Philips

Philips Disney Softpal Sulley Manual de usuario

Philips

Philips Lightolier Solution Series Manual de usuario

Philips

Philips Ecomoods 57940/31/96 Manual de usuario

Philips

Philips 56432-31-16 Manual de usuario

Philips

Philips SC Series Manual de usuario

Philips

Philips ColorDial Pro Manual de usuario

Philips

Philips LX25 Series Manual de usuario

Philips

Philips Selecon Accent LED Beamshaper Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario