Philips QC5099 Manual de usuario
QC5099
2
3
1 2 3 4
56 7 8
9 10 11 12
13 14 15 16
17 18
4
QC5099
ENGLISH 6
DANSK 13
DEUTSCH 19
26
ESPAÑOL 34
SUOMI 41
FRANÇAIS 47
ITALIANO 54
NEDERLANDS 61
NORSK 68
PORTUGUÊS 74
SVENSKA 81
TÜRKÇE 88
6
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet
from the support that Philips offers, register your product at www.philips.
com/welcome.
Your new Philips 3D hair clipper adapts to the contours of the head and
enables comfortable use.
Important
Read this user manual carefully before you use the appliance and save it
for future reference.
Danger
- Make sure the adapter does not get wet.
Warning
- Check if the voltage indicated on the adapter and on the appliance
corresponds to the local mains voltage before you connect the
appliance.
- The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
- If the adapter is damaged, always have it replaced with one of the
original type in order to avoid a hazard.
- This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person
responsible for their safety.
- Children should be supervised to ensure that they do not play with
the appliance.
Caution
- Never immerse the appliance in water or any other liquid, nor rinse it
under the tap.
- Use, charge and store the appliance at a temperature between 15°C
and 35°C.
- Only use the adapter supplied.
- Do not use a damaged adapter.
ENGLISH
- If the adapter is damaged, always have it replaced with one of the
original type in order to avoid a hazard.
- Do not charge the appliance in a pouch or cassette.
- Do not use the appliance when one of the attachments is damaged
or broken, as this may cause injury.
- This appliance is only intended for clipping human scalp hair. Do not
use it for any other purpose.
- This appliance is suitable for mains voltages from 220 to 240 volts.
General
- The adapter transforms 100-240 volts to a safe low voltage of less
than 24 volts.
This Philips appliance complies with all standards regarding
electromagnetic elds (EMF). If handled properly and according to the
instructions in this user manual, the appliance is safe to use based on
scientic evidence available today.
Charging
Charge the appliance for 12 hours before you use it for the rst time.
A fully charged appliance has a cordless clipping time of up to 50 minutes.
Do not charge the appliance for more than 24 hours.
1 Make sure the appliance is switched off.
2 Insert the appliance plug into the appliance (Fig. 1).
3 Insert the adapter into the wall socket.
,The charging light goes on to indicate that the battery is being
charged.
Note:The charging light does not go out or change colour when the appliance
is fully charged.
ENGLISH 7
- After you have charged the appliance for the rst time, do not
recharge it between clipping sessions. Continue using it and recharge
it only when the battery is (almost) empty.
- Discharge the battery completely twice a year by letting the motor
run until it stops.
- Do not keep the appliance plugged in continuously.
- If you have not used the appliance for a long time, recharge it for 12
hours.
Select the small or large comb attachment, depending on the desired hair
length.
Hair length settings:
- The hair length settings are indicated in millimetres on the arms of
the comb attachment.The settings correspond to the remaining hair
length after cutting (Fig. 2).
- The small comb attachment cuts hair to a length of 3mm, 6mm, 9mm,
12mm, 15mm, 18mm or 21mm.
- The large comb attachment cuts the hair to a length of 23mm, 26mm,
29mm, 32mm, 35mm, 38mm or 41mm.
1 Slide the arms of the comb attachment into the guiding grooves of
the appliance (‘click’) (Fig. 3).
2 To set the comb attachment to the desired hair length, turn the
hair length adjustment ring to the right or to the left (Fig. 4).
3 Switch on the appliance.
- We advise you to start clipping at the highest setting of the large
comb attachment and to reduce the hair length in small steps until
you reach the desired hair length.
- If a lot of hair has accumulated in the comb attachment, remove the
comb attachment and blow and/or shake the hair out of it. Removing
ENGLISH8
the comb attachment does not change the selected hair length
setting.
- Write down the hair length settings used to create a certain hairstyle
as a reminder for future clipping sessions.
You can use the clipper without comb attachment to contour the
neckline and the area around the ears.
- To remove the comb attachment, pull it off the appliance (Fig. 5).
Never pull at the exible top of the comb attachment. Always pull at the
bottom part.
- The comb attachment keeps the cutting unit at a certain distance
from your head.This means that, if you use the clipper without the
comb attachment, your hair will be cut off very close to the skin.
You can use the precision trimmer for precise contouring and dening.
1 Push the middle part of the cutting unit upwards with your thumb
until it opens and then pull it off the appliance (Fig. 6).
Be careful that the cutting unit does not fall to the oor.
2 Place the lug of the precision trimmer into the slot and push the
unit back onto the appliance (‘click’) (Fig. 7).
Corded clipping
When the rechargeable battery is empty, you can also run the appliance
from the mains.
Do not run the appliance from the mains when the battery is fully
charged.
To use the hair clipper connected to the mains:
1 Switch off the hair clipper and connect it to the mains.
2 Wait a few seconds and then switch on the appliance.
ENGLISH 9
Cleaning
Clean the appliance every time you have used it.
Never use scouring pads, abrasive cleaning agents or aggressive liquids
such as alcohol, petrol or acetone to clean the appliance.
Only clean the appliance and the adapter with the cleaning brush
supplied.
1 Make sure the appliance is switched off and disconnected from the
mains.
2 Pull the comb attachment off the appliance (Fig. 5).
3 Push the middle part of the cutting unit upwards with your thumb
until it opens and then pull it off the appliance (Fig. 6).
Be careful that the cutting unit does not fall to the oor.
4 Clean the cutting unit with the cleaning brush supplied (Fig. 8).
5 Clean the inside of the appliance with the cleaning brush supplied.
6 Place the lug of the cutting unit into the slot and push the unit back
onto the appliance (‘click’) (Fig. 7).
Note:This appliance does not need any lubrication.
Replacement
Only replace a damaged or worn cutting unit with an original Philips
cutting unit.
1 Push the middle part of the cutting unit upwards with your thumb
until it opens and then pull it off the appliance (Fig. 6).
2 Place the lug of the new cutting unit into the slot and push the unit
back onto the appliance (‘click’) (Fig. 7).
ENGLISH10
Otros manuales para QC5099
1
Tabla de contenidos
Idiomas:
Otros manuales de Cortapelos de Philips
Philips
Philips HQC644 Manual de usuario
Philips
Philips HQC486/00 Manual
Philips
Philips HC7460/13 Manual de usuario
Philips
Philips HC9450 Manual de usuario
Philips
Philips NORELCO QC5340 Important s Manual de usuario
Philips
Philips QC5375 Manual de usuario
Philips
Philips QC5390 Manual de usuario
Philips
Philips BT9295 Manual de usuario
Philips
Philips NORELCO BT5210 Manual de usuario
Philips
Philips NORELCO CC5060 Manual de usuario
Philips
Philips QC5002 Manual de usuario
Philips
Philips Norelco QC5510 Manual de usuario
Philips
Philips HC9450/20 Manual de usuario
Philips
Philips QC5010 Manual de usuario
Philips
Philips QG3371 Manual de usuario
Philips
Philips BT3222 Manual de usuario
Philips
Philips QC5580/32 Manual de usuario
Philips
Philips HQC688 Manual de usuario
Philips
Philips QC5055/40 Manual de usuario
Philips
Philips QC5170 Manual de usuario
