Philips DS9000 Manual de usuario

Installation Guide

DS-9000 / DS-9100 Series DVR (V1.0.2)

Installation Guide - DS-9000 / DS-9100 Series DVR 1

Verify Contents

Verify that the package contents are correct by checking the

items against the packing list.

Note: Please contact your dealer for damaged or missing

items.

DVR Pre-Installation

The DS-9000 and DS-9100 Series DVRs are highly advanced

surveillance equipment that should be installed with care.

Please take into consideration the following precautionary

steps before installation of the DVR.

1. Keep all liquids away from the DVR.

2. Install the DVR in a well-ventilated and dust-free area.

3. Ensure environmental conditions meet factory

specifications.

4. Install a manufacturer recommended HDD.

DVR Installation

During the installation of the DVR:

1. Use brackets for rack mounting.

2. Ensure there is ample room for audio and video cables.

3. When installing cables, ensure that the bend radius of the

cables are no less than five times than it’s’ diameter.

4. Connect both the alarm and RS-485 cable.

5. Allow at least 2cm (~0.75in) of space between racks

mounted devices.

6. Ensure the DVR is grounded.

7. Environmental temperature should be within the range of

-10ºC ~ 55ºC, 14ºF ~ 131ºF.

8. Environmental humidity should be within the range of

10% ~ 90%.

Hard Disk Installation

Before installing a hard disk drive (HDD), please make sure

the power is disconnected from the DVR. A factory

recommended HDD should be used for this installation.

Tools Required: Phillips screwdriver.

To install a HDD on your

DVR:

1. Remove the lid of the

DVR by unfastening

the screws on the back.

2. Install the HDD in the

HDD rack using the

pro- vided screws. To

install on the bottom

HDD rack, the top

HDD rack must be

removed first.

3. Connect the HDD to

the motherboard of the

DVR with the included

data cable.

4. Connect the power

cable to the HDD.

5. Re-install the lid of the

DVR and fasten

screws.

2 Installation Guide - DS-9000 / DS-9100 Series DVR

Rear Panel Diagram

No. Item Description

1 VIDEO IN BNC connectors for analog video input.

AUDIO IN BNC connectors for analog audio input.

2 VIDEO SPOT OUT BNC connector for monitor. If VGA is connected, it is for video output only. If VGA

is not connected, it is for video output, playback and showing PTZ controls.

AUDIO SPOT OUT BNC connector for audio output. If VGA is connected, audio is synchronized with

VGA. If VGA is not connected, audio is synchronized with VIDEO SPOT OUT.

3 VIDEO OUT BNC connector for video output. If VGA is connected, it is used for spot output only

with local video display, playback, recording and PTZ controls. If VGA is not

connected, it is used as the main video output with local video display and menu

operations.

AUDIO OUT BNC connector for audio output. This connector is synchronized with VIDEO OUT.

4 LINE IN BNC connector for audio input.

5 VGA DB9 connector for VGA output. Display local video output and menu.

6 Loop Out (Optional) DB15 interface for connection video matrix and monitor.

7 RS-232 Interface Connector for RS-232 devices.

8 eSATA (Optional) Connects external SATA HDD, CD/DVD-RM or disk array.

9 LAN Interface Connector for LAN (Local Area Network).

10 USB Interface Connector for USB devices.

11 Termination Switch RS-485 termination switch.

Up position is not terminated. Down is 120Ω termination.

12 RS-485 Interface Connector for RS-485 devices. T+, T- pin connects to PTZ.

Controller Port D+, D- pin connects to Ta, Tb pin of controller. For cascading devices, the first

DVR’s D+, D- pin should be connected with the D+, D- pin of the next DVR.

ALARM IN Connector for alarm input (up to 16 channels).

ALARM OUT Connector for alarm output (4 channels).

13 GROUND Ground(needs to be connected when DVR startup)

14 POWER AC 110V ~ 220V

Installation Guide - DS-9000 / DS-9100 Series DVR 3

Peripheral Connections

Connecting to Alarm Input / Output Device

The alarm input/output interface of the DVR is shown below:

The alarm input is an open/close relay. If the input is not an

open/closed relay, follow the connection diagram below:

To connect to an AC/DC load, use the following diagram:

For DC load, JP4 can be used within the limit of 12V/1A

safely. If the interface is connected to an AC load, JP4 should

be left open. Use an external relay for safety (as shown in the

figure above).

There are 4 jumpers (JP4, JP5, JP6, and JP7) on the

motherboard, each corresponding with one alarm output. By

default, jumpers are connected. To connect an AC load,

jumpers should be removed.

Note: An external relay is needed to prevent electric shock

when connecting to an AC load.

Alarm Connection

To connect alarm devices to the DVR:

1. Disconnect pluggable block from the ALAM IN /ALARM

OUT terminal block.

2. Unfasten stop screws from the pluggable block, insert

signal cables into slots and fasten stop screws. Ensure

signal cables are in tight.

3. Connect pluggable block back into terminal block.

RS-485 Connection

To connect RS-485 devices to the DVR:

1. Disconnect pluggable block from the RS-485 terminal

block.

2. Unfasten stop screws from the pluggable block, insert

signal cables into slots and fasten stop screws. Ensure

signal cables are in tight.

3. Connect pluggable block back into terminal block.

4 Installation Guide - DS-9000 / DS-9100 Series DVR

Note: The RS-485 PTZ control should be connected with

the

T+ and T- pin on the RS-485 terminal block.

Controller Connection

To connect a controller to the DVR:

1. Disconnect pluggable block from the KB terminal block.

2. Unfasten stop screws from the KB D+, D- pluggable

block, insert signal cables into slots and fasten stop

screws. Ensure signal cables are in tight.

3. Connect Ta on controller to D+ on terminal block and Tb

on controller to D- on terminal block. Fasten stop screws.

4. Connect pluggable block back into terminal block.

Note: Make sure both the controller and DVR are grounded.

HDD Storage Calculation

Chart

The following chart shows an estimation of storage space

used based on recording at one channel for an hour at a fixed

bit rate.

Bit Rate Storage Used

96K 42M

128K 56M

160K 70M

192K 83M

224K 98M

256K 112M

320K 140M

384K 168M

448K 196M

512K 225M

640K 281M

768K 337M

896K 393M

1024K 450M

1280K 562M

1536K 675M

1792K 787M

2048K 900M

Note: Please note that supplied values for storage space

used is just for reference. Storage space used is estimated by

formulas and may have some deviation from actual value.

Otros manuales para DS9000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de DVR de Philips

Philips

Philips DVR1EP08 Manual de usuario

Philips

Philips VR6670 Manual de usuario

Philips

Philips DSR7000 Manual de usuario

Philips

Philips Divar Manual de usuario

Philips

Philips Desa DR16124 Manual de usuario

Philips

Philips DVR7100/75 Manual de usuario

Philips

Philips DVR I Series Instrucciones de instalación y funcionamiento

Philips

Philips DSR7000 Manual de usuario

Philips

Philips VR140/58 Manual de usuario

Philips

Philips DVR2008/97 Manual de usuario

Philips

Philips VR 210/07 Manual de usuario

Philips

Philips Divar Digital versatile recorder Manual de usuario

Philips

Philips VR130/39 Manual de usuario

Philips

Philips DVDR730/0x Manual de usuario

Philips

Philips HDR5710 Manual de usuario

Philips

Philips DVR5100 Manual de usuario

Philips

Philips Cineos DVDR9000H Manual de usuario

Philips

Philips VR558 Manual de usuario

Philips

Philips DVR7100 Manual de usuario

Philips

Philips Cineos DVDR9000H Manual de usuario

Philips

Philips DSR7000R Manual de usuario

Philips

Philips HDR5750 Manual de usuario

Philips

Philips LTC3906/50 Manual de usuario

Philips

Philips VR820 Manual de usuario

Manuales populares de DVR de otras marcas

FLIR

FLIR M3100E Series Manual de usuario

VTRACKPRO

VTRACKPRO FPRO300 Manual de usuario

Swann

Swann NVR-7085 models Manual de usuario

XtendLan

XtendLan DVR-1670C Manual de usuario

urmet domus

urmet domus 1093/004AHD Manual de usuario

Holux

Holux M1 Manual de usuario

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manual de usuario

Whistler

Whistler D16VRS Manual de usuario

Defender Security

Defender Security 82-20235 Manual de usuario

MISUMI

MISUMI MP-WF100M Manual de usuario

Speco

Speco D8HU Manual de usuario

UST

UST DDR-E04AA Instrucciones de uso

Consolidated

Consolidated Digital Video Recorder Manual de usuario

Mace

Mace DVR0404RW Guía de inicio rápido

RCA

RCA RTD315W Manual de usuario

FSM

FSM Colibri Grande PRO Manual de usuario

Hauppauge

Hauppauge HD PVR 2 Manual de usuario

Identivision

Identivision ICR-PH161i PIONEER Manual de usuario