Philips DVD701AT Documento técnico
DVD Video player
DVD701
Toll Free Help Line
Ligne d'assistance en service libre
Linea de ayuada telefónica sin cargo
800-531-0039
Hookup Pages
10 FUNCTIONAL OVERVIEW
Functional overview
Front panel
9STOP
- stops video/audio play
;PAUSE
- interrupts video/audio play or advances
to the next picture frame
/OPEN/CLOSE
- opens/closes the disc tray
Disc tray
PLAY
PREV
STOP
NEXT
SOUND
OPEN
/CLOSE PAUSE
POWER ON/OFF
DVD 701
DVD/VIDEO CD/CD PLAYER
TRACKTITLESCANPAUSE
TIMETRACKTOTAL REM
CHAPTER
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
CD
REPEAT
SHUFFLE
F S
T
CHAPTERTITLE TRACK
V
-BA
. ........ . . . . .
+
SOUND
- selects Stereo, Dolby Surround or 3D-Sound
S
- PREVious title/chapter/track
2PLAY
- starts video/audio play
T
- NEXT title/chapter/track
Display
- shows the current status of the player
Standby indicator - lights red when the player is in Standby mode
POWER ON/OFF - switches the player to ON or OFF
FUNCTIONAL OVERVIEW 11
Rear panel
Caution: Do not touch the inner pins of the jacks on the rear
panel connectors. Electrostatic discharge may cause permanent
damage to the unit.
L
RCVBS
VIDEO OUT
COAXIAL AUDIO S-VIDEO OUT
1
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
1
22
MAINS
Y/C
Video Out (CVBS)
- connect to a TV with CVBS video inputs
Video Out (S-Video)
- connect to a TV with S- Video (Y/C) inputs
Digital audio out jack (coaxial)
- connect to digital (coaxial) equipment
Audio / L/R (Left/Right)
- connect to an amplifier, receiver or stereo system
MAINS (AC) power jack
- connect to the power source
14 PREPARATION
Preparation
General notes
- Depending on your TV and other equipment you wish to connect,
there are various ways you could connect the player. Possible
connections are shown in the following drawings.
Please refer to the manuals of your TV,VCR, Stereo System or other
devices as necessary to make the best connections.
- Do not connect your DVD-player via your VCR.The video
quality could be distorted by the copy protection system.
- For better sound reproduction, connect the player’s audio out jacks
to the audio in jacks of your amplifier, receiver, stereo or A/V
equipment. See ‘Connecting to optional equipment’.
Caution: Do not connect the player’s audio out jack to the
phono in jack of your audio system.
Connecting to a TV
S-Video connection.
1Connect the S-Video connector on the rear of the player to the
corresponding connector on the TV using the S-Video cable (not
supplied).
2Connect the audio Left and Right channel sockets on the player rear
panel to the corresponding sockets on your TV or stereo system (e.g.
AUX, CD, etc.).
Video CVBS connection
1Connect the Video socket on the rear of the player to the
corresponding socket on the TV using the cable supplied.
2 Connect the audio Left and Right channel sockets on the rear of the
player to the corresponding sockets on the TV using the cable supplied.
Alternatively, you can use the same cable to connect the audio Left and
Right sockets on the rear of the player to the corresponding sockets on
your TV or stereo system (e.g. AUX, CD, etc.).
L
RCVBS
VIDEO OUT
COAXIAL AUDIO
1
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
1
22
Y/C
S-VIDEO OUT
VIDEO
IN
A/V CABLE
AUDIO
IN
TV
S-VIDEO CABLE
TV
L
RCVBS
VIDEO OUT
COAXIAL AUDIO
1
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
1
22
Y/C
S-VIDEO OUT
PREPARATION 15
Connecting to optional equipment
Connecting to an amplifier equipped with digital
stereo
●For multi-channel sound, your player provides both digital and analog
audio outputs.
Connecting to an A/V receiver equipped with a multi-
channel decoder (Dolby Digital™ (AC-3) , MPEG 2 and
DTS)
Digital Multi-channel sound
Digital multi-channel connection provides the best sound quality. For this
you need a multi-channel A/V receiver that supports one or more of the
audio formats supported by your DVD player (MPEG 2, Dolby
Digital
™(AC-3)
and DTS). Check the receiver manual and the logos on
the front of the receiver.
1
Connect the player’s digital audio or digital coaxial output to the
corresponding input on the receiver using the optional digital audio
cable.(not supplied) In this case, do not use the player’s audio Left and
Right outputs.
2You will need to activate the digital output of the player (See Settings).
3The audio format of the digital output is dependent on the audio format
of the selected audio stream. Make sure that the selected audio stream
matches the capabilities of the receiver connected to the digital output.
Connecting to an amplifier equipped with Dolby
Surround™
1If your TV set has a Dolby Pro Logic™ decoder, you simply hook up the
player to the TV using the S-Video, or Video (CVBS) and audio
connections.
2If not, you need to make the S-Video, or Video (CVBS) connection to the
TV, and connect the player’s audio Left and Right outputs to the
corresponding inputs on a Dolby Pro Logic™ Audio/Video receiver, using
the cable supplied.
3For speaker connections, follow the instructions given in the TV set or
A/V receiver user manual.
NOTE
If the audio format of the digital output does not match the capabilities of
your receiver, the sound will be muted.
L
RCVBS
VIDEO OUT
COAXIAL AUDIO
1
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
1
22
Y/C
S-VIDEO OUT
MAINS
DIGITAL AUDIO
IN
RECEIVER
DIGITAL AUDIO
CABLE (optional)
16 PREPARATION
Connecting the power cord
1Plug the female end of the supplied power cord into the Mains (AC) jack
on the rear of the player.
2Connect the other end of the cord to an AC outlet.
Note:
When the player is in the “STANDBY” mode, it is still consuming some
power. If you wish to disconnect your player completely from the power, press
POWER ON/OFF
Caution: Only qualified service personnel should remove the
cover or attempt to service this device.
Remote control battery installation
Loading the batteries
1Open the battery compartment cover.
2Insert batteries as indicated inside the battery compartment.
3Close the cover.
Caution: Do not mix old and new batteries. Never mix
different types of batteries (standard, alkaline, etc.).
NTSC/PAL Settings
You can switch the NTSC/PAL setting of the DVD player to match the
video signal of your TV.This setting only affects the television’s on-screen
display that shows the stop and setup modes.You may select either
NTSC or PAL.To change the DVD player setting to PAL or NTSC,
follow the steps below.
1Press the POWER ON/OFF button on the front panel of the DVD
player to turn OFF the DVD player.
2Press and hold /and Ton the front of the DVD player.While
holding /and T, press POWER ON/OFF.
3After PAL or NTSC appears on the display panel of the DVD player,
release /and Tat the same time.The PAL or NTSC that appears on
the display panel indicates the current setting.
4To change the setting, press Twithin three seconds.The new setting
(PAL or NTSC) will appear on the display panel.
+
-
+
-
Otros manuales para DVD701AT
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Reproductor de DVD de Philips
Philips
Philips DVP 5160 Manual de usuario
Philips
Philips DVD-762 Manual de usuario
Philips
Philips DVP3560 Manual de usuario
Philips
Philips DVD-722 Manual de usuario
Philips
Philips DVP3388 Manual de usuario
Philips
Philips DVP3250K Manual de usuario
Philips
Philips DVD726v2 Manual de usuario
Philips
Philips DVP3950 Manual de usuario
Philips
Philips DVP3552K/96 Manual de usuario
Philips
Philips DVP3310K/93 Manual de usuario
Philips
Philips DVP3800 Instrucciones de funcionamiento
Philips
Philips DVP3010/05 Manual de usuario
Philips
Philips DVD702 Manual de usuario
Philips
Philips DVP3520KX/78 Manual de usuario
Philips
Philips DVP 5140K Manual de usuario
Philips
Philips DVP2850 Manual de usuario
Philips
Philips DVD963SA/051 Manual de funcionamiento
Philips
Philips DVP534K/75 Manual de usuario
Philips
Philips DVD736K Manual de usuario
Philips
Philips DVP3880K Manual de usuario
