Philips BDP9100/12 Manual de usuario
Service Manual
Service
Service
Service
Service
Service
BDP5000/12 & BDP7300/12/51/93/98
©Copyright 2009 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
Published by LO-YY 0913 AV System Printed in The Netherlands Subject to modification
GB
3139 785 34861
Blu-ray Disc Player
Version 1.1
CONTENT
Page
1Technical Specifications and Connection Facilities
1-1 PCB Location 02
1-2 BDP-9100 Specification 03
2Safety Information and General Notice
2-1 Safety Instructions 04
2-2 Laser Beam Safety Precautions 06
3Quick Start Guide
3-1 Quick Start Guide 08
4Mechanical Instructions
4-1 Dismantling Door of Driver (Loader) 11
4-2 Dismantling Front Panel 12
4-3 Dismantling Rear Panel 13
4-4 Dismantling Driver (Loader) 14
4-5 Dismantling Digital Board 15
4-6 Dismantling Analog Board 16
4-7 Dismantling PSU Board 17
5Firmware Upgrading Procedure
5-1 Upgrade Firmware of System and Loader 18
5-2 Service Diagnostics Process 24
6Functional Test & Trouble Shooting Procedures
6-1 Flow Chart on How to Filter between Working and Defective Sets 26
6-2 Trouble Shooting 27
7Block Diagram
7-1 Block diagram 31
7-2
7-3
7-4
7-5
7-6
Front Board Diagrams
Digital Board Diagrams
Analog Board Diagrams
Standby Board Diagrams
PSU Board Diagrams
32
34
43
47
48
8Exploded View
8-1 BDP-9100 Exploded View 50
8-2 Packing Exploded View 51
9Service Parts & Screws List
9-1 Parts & Screws List of BDP-9100 52
10 Revision List
10-1 RevisionList 54
1
Technical Specifications & Connection Facilities
1. Technical Specifications and Connection Facilities
1-1.PCB Locations
Analog
Board Digital
Board PSU
Board
BD
DRIVER
(LOADER)
Front Cabinet
Standby Board
(
Behind the Front Cabinet
)
Front Board
(Behind the
Front Cabinet)
Rev. A
2
Technical Specifications & Connection Facilities
1-2 BDP 9100 Specifications
1-2-1 Playback Media
BD-Video,
DVD-Video,
DVD+/- R,
DVD +/- RW,
CD -R/CD-RW,
Audio CD, Video CD/SVCD,
Picture CD,
MP3 –CD,
MP3-DVD,
WMA-CD,
DivX (Ultra),
USB flash driver
1-2-2 Video
Signal system: PAL/NTSC
Composite video output: 1 Vp-p (75 ohm)
Component video output:
zY: 1 Vp-p ( 75 ohm )
zPb: 0.7 V-pp ( 75 ohm )
zPr: 0.7 V-pp ( 75 ohm )
HDMI output:
480p/576p/720p/1080i/1080p
1-2-3 Audio
2 channel analogue output
zAudio Front L+R: 2Vrms (>1kohm)
5.1 channel analogue output
zAudio Front L+R: 2Vrms (>1kohm)
zAudio Surround L+R: 2Vrms
(>1kohm)
zAudio Center: 2Vrms (>1kohm)
zAudio Subwoofer: 1.15 Vrms
(>1kohm)
Digital output: 0.5 Vp-p (75 ohm )
zOptical / Coaxia
HDMI output:
Sampling Frequency:
zMP3 : 32 / 44.1 / 48 KHz
zWMA: 44.1 / 48 KHz
Constant bit rate:
zMP3 : 112 – 320 Kbps
zWMA: 48 – 192 Kbps
1-2-4 USB
Compatibility: Hi-Speed USB 2.0
Class Support:
zUMS (USB mass Storage Class)
zMTP (Media Transfer protocol)
1-2-5 Main Unit
Power supply rating: 110-240 V ~AC 50Hz
Power consumption: 30 W
Power consumption in standby mode:
0.2W
Rev. A
3
Safety Information & General Notice
REV.A
4
2. Safety Information & General Notice
2-1 Safety Instructions
2-1-1 General Safety
Safety regulations are strongly required during repair action:
• Using isolation transformer to connect unit and mains.
• Replace safety components which have symbol on it only allowed to change the component
as same type as original one. Any other substitution component may cause risk of fire or electrical
short circuit issue.
Safety regulations are required after repair. You must return the unit back to original condition and
pay attention at the following points:
• Route the wires/cables correctly, and fix them with the mounted cable clamps.
• Check the insulation of the mains lead for external damage.
• Check the electrical DC resistance between the mains plug and the secondary side:
1. Unplug the mains cord, and connect a wire between the two pins of the mains plug.
2. To set the mains switch to the ‘on’ position (keep the mains cord unplugged!).
3. Measure the resistance value between the mains plug and the front panel, controls, and chassis
bottom.
4. Repair or correct unit when the resistance measurement is less than 1 M .Ω
5. Verify this, before you return the unit to the customer/user
6. Switch the unit ‘off’, and remove the wire between the two pins of the mains plug.
Laser Safety
The BD Driver is a laser device. Only allowed qualified service personnel to remove the cover and
repair action, because it might cause eye damage.
Laser Device Unit
Type : Semiconductor laser GaAlAs
Wavelength : 775-805 nm (CD)
: 640-663 nm (DVD)
: 400-410 nm (Blu-ray)
Output Power : 7 mW (CD)
: 7 mW (DVD)
: 20mW (Blu-ray)
Beam divergence : 60 degree
Safety Information & General Notice
REV.C
5
2-1-2 Warnings
General
• All components which have been set on PCB board such as IC or Semiconductor are very
sensitive to static discharges (ESD ). Careless handling during repair can cause component
damage. Therefore, profession service man are not only to keep them at the same potential as the
mass of the set by a wristband with resistance but also have to keep components and tools at this
same potential while assembling or disassembling parts.
• Be careful during measurements in the live voltage section. The primary side of the power supply,
including the heats ink, carries live mains voltage when you connect the player to the mains (even
when the player is ‘off’!). It is possible to touch copper tracks and/or components in this unshielded
primary area, when you service the player. Service personnel must take precautions to prevent
touching this area or components in this area. A ‘lightning stroke’ and a stripe-marked printing on
the printed wiring board, indicate the primary side of the power supply.
• Never replace modules or components, while the unit is set at ‘on’ position.
Laser
• The laser products which been used at BD Player driver will cause eyes damage.
• Only qualified service engineer can remove the cover of laser product and maintain this device.
• Repair handling should put a disc inside the player.
Safety Information & General Notice
REV.A
6
2-2 LASER BEAM SAFETY PRECAUTIONS
This BD player uses a pickup which will emits laser beam.
Do not look laser beam which
comes from pickup directly
The laser beam will be emitted from pickup as shown above figure. Please be sure, there are more
then 30 cm away between your eyes and pickup lens, while laser equipment is turned on. Do not
look laser beam directly.
CAUTION: Use of controls and adjustments, or doing procedures other than those specified here in,
may result in hazardous radiation exposure.
Safety Information & General Notice
REV.C
7
Driver
Mechanism
Assy.
Driver
Mechanism
Assy.
Laser
Pickup Laser Beam
Radiation
Turntable Tray Dish
Mechanism of BD Driver
Quick Start Guide
9
3. QUICK START GUIDE
3-1 Quick Start Guide
The following excerpt of the Quick Start Guide serves as an introduction to the set.
The complete Direction for Use can be downloaded in different languages from the internet
site of Philips Consumer Care Center: www.p4c.philips.com
Quick Start Guide
10
Tabla de contenidos
Otros manuales de Reproductor de Blu-ray de Philips
Philips
Philips BDP3020/F7 Manual de usuario
Philips
Philips BDP1200 Manual de usuario
Philips
Philips HTS3582/93 Manual de usuario
Philips
Philips BDP2100/F7 Manual de usuario
Philips
Philips HTS3306/F7 Manual de usuario
Philips
Philips BDP2205 Manual de usuario
Philips
Philips HTB3560/12 Manual de usuario
Philips
Philips BDP9000 Manual de usuario
Philips
Philips BDP2500 Manual de usuario
Philips
Philips BDP5012/F7 A Manual de usuario
Philips
Philips BDP9500/12 Manual de usuario
Philips
Philips BDP3000/51 Manual de usuario
Philips
Philips BDP3380K Manual de usuario
Philips
Philips BDP5502 Manual de usuario
Philips
Philips BDP7100 Manual de usuario
Philips
Philips DVP3681K Manual de usuario
Philips
Philips BDP2610/93 Manual de usuario
Philips
Philips BDP5600K/51 Manual de usuario
Philips
Philips PB9001/37 Manual de usuario
Philips
Philips BDP3480/93 Manual de usuario
