Philips BDP3406 /F7 Manual de usuario
BDP3406 /F7
© Copyright 2011 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without
the prior permission of Philips.
Blu-ray Disc Player
Version 1.1
Published BG AVM ASD-CY Printed in The Netherlands Subject to modification
TABLE OF CONTENTS
Chapter
Technical Specification, PCBs Location………………….. 1
Safety Instruction ……………………………………………… 2
Instruction for Use……………………………………………… 3
Mechanical and Dismantling Instructions…………………. 4
Service Modes, Troubleshooting……………………………. 5
Overall Block Diagram, Wiring Diagram……………………. 6
Electrical Diagram……………………………………………… 7
Exploded View Diagram & Service Part List………………..8
Revision List……………………………………………………. 9
3141 785 36331
Cau on: These servicing instruc ons are for use by qualifieded service personnel only. To reduce
the risk of electric shock do not perform any servicing other than that contained in the opera ng
instruc ons unless you are qualifi
.osodotde
Remark: The Service Manual only for S/N starting from GS1Axxxxxxxxxx. For
defective sets with S/N GS1Bxxxxxxxxxx, please refer to Service Manual
with code number 314178536661.
1.1 Specifications
Specifications are subject to change without notice
1-1
Playable media
- BD-Video
- DVD-Video, DVD+R/+RW, DVD-R/-RW, DVD+R/-R DL (Dual Layer)
- VCD/SVCD
- Audio CD, CD-R/CD-RW, MP3 media, WMA media, JPEG iles
- DivX (Ultra)/DivX Plus HD media, MKV media
- USB storage device
File format
- Video: .avi, .divx, .mp4, .mkv
- Audio: .mp3, .wma, .wav
- Picture: .jpg, .gif, .png
Video
- Signal system: PAL / NTSC
- Composite video output: 1 Vp-p (75 ohm)
- HDMI output 480p, 576p, 720p, 1080i, 1080p, 1080p24
Audio
- 2 Channel analog output
- Audio Front L&R : 2 Vrms (> 1 kohm)
- Digital output: 0.5 Vp-p (75 ohm)
- Coaxial
- HDMI output
- Sampling frequency:
- MP3: 32 kHz, 44.1 kHz, 48 kHz
- WMA: 44.1 kHz, 48 kHz
- Constant bit rate:
- MP3: 112 kbps - 320 kpbs
- WMA: 48 kpbs - 192 kpbs
USB
- Compatibility: Hi-Speed USB (2.0)
- Class support: USB Mass Storage Class (UMS)
- File system: FAT16, FAT32
- Support HDD (a portable hard drive disc): an external power source may be needed.
Main unit
- Power supply rating: AC 110-120V~, 50Hz - 60Hz
- Power consumption: 18 W
- Power consumption in standby mode: < 1 W
- Dimensions (w x h x d): 435 X 41 X 195.5 (mm)
- Net Weight: 1.47 kg
Accessories supplied
- Remote control and batteries
- User manual
Laser Specification
- Laser Type (Diode): AlGaInN (BD), AlGaInP (DVD/CD)
- Wave length: 405+7nm/-7nm (BD), 655+10nm/-10nm (DVD), 790+10/-20nm (CD)
- Output power: 1mW (BD), 0.26mW (DVD), 0.3mW (CD)
1.1 PCBs Location
VERSION VARIATIONS
Type/Versions:
Service policy
Board in used:
BDP3406
*TIPS: C -- Component Lever Repair.
M -- Module Lever Repair
X -- OCX
1-2
M
F7
PSU PCBA
LED DISPLAY PCBA M
MAIN BOARD
M
LED DISPLAY PCBA
PSU PCBA
MAIN BOARD
Software check and upgrade
Preparation to upgrade software
1)Start the CD burning software & create a folder named "UPG_ALL", B. Read out the software versions to confirm upgrading
2)Then copy the Bin file (BDP3XXXXX-XXX-XXXXXX.bin) into it,
3)Burn the data onto the blank CD.
A. Procedure for software upgrade
A) Upgrade software via Disc
4) In homemenu,enter "setup"->"advanced"->"version info", press "OK"
1) Power on the set and insert the prepared Upgrade
CDR.
and other information will display on the TV screen as below:
2) The set will starts reading disc & response with the Model:XXX.XXX
following display TV screen: Versions
Now searching for upgrade software!
Please wait…!
3) Then screen will display :
software upgrades for this player has been found!Do you want to upgrade? Caution: The set must not be power off during
upgrading, otherwise the Main board will be
Cancel Start damaged entirely.
4) Press Right cursor button to choose "Start", then press <OK>;
5) The software will updagrde and screen will display as below:
Upgrade is ongoing, Please wait…
Please do not unplug or switch off the device.
6) Restart the set.
B) Update software via USB Flash Drive:
1) Go to www.philips.com/support to check if the latest software
version is available for this player.
2) Download the software onto a USB flash drive's root DIR named "UPG_ALL".
3) Insert the USB flash drive to the USB jack of the rear panel.
4) In the Home menu, select <Setup>-<Advanced>-<Software
update>-<USB>.
5) Then press OK
6) you'll see now searching for new software, please wait.......
7) Waiting, the you'll see "software for this player has been found ......"
8) Then select "Start" and press "OK"
9) then you'll see "upgrade is ongoing ......", wait until it ends.
10) Player will restart automatically or press "Restart now" to restart, after restarting the upgrade ends.
subinfo:xxxx
system SW:xxxx
ethernet MAC:xxxxxxxx
http://www.philips.com/support
1-3
2.0 Safety instruction
1. General
safety
Safety regulations require that during a repair:
. Connect the unit to the mains via an isolation
transformer.
. Replace safety components indicated by the
symbol
Only by components identical to the original ones.
Any
Other component substitution (other than original
type)
May increase risk of fire or electrical shock hazard.
Safety regulations require that after a repair, you
must
Return the unit in its original condition. Pay, in
particular,
Attention to the following points:
. Route the wires/cables correctly, and fix them with
the
mounted cable clamps
. Check the insulation of the mains lead for external
Damage
. Check the electrical DC resistance between the
mains
Plug and the secondary side:
1) Unplug the mains cord, and connect a wire
between
The two pins of the mains plug.
2) Set the mains switch the “on” position (keep
the
Mains cord unplug).
3) Measure the resistance value between the
mains
plug and the front panel, controls, and chassis
bottom.
4) Repair or correct unit when the resistance
measurement is less than 1M Ω
5) Verify this, before you return the unit to the
customer/user (ref. UL-standard no. 1492).
6) Switch the unit “off”, and remove the wire
between
the two pins of the mains plug.
2. Laser safety
This unit employs a laser. Only qualified service
personnel
May remove the cover, or attempt to service this
device
(due to possible eye injury).
Laser device unit
Type :Semiconductor laser GaAIAs
Wavelength :650nm (DVD)
:780nm (VCD/CD)
Output power :7mW(DVD)
:10mW(DVD/CD)
Beam divergence:60 degree
Note: Use of controls or adjustments or
performance of procedure other than those
specified herein, may result in hazardous
radiation exposure. Avoid direct exposure to
beam.
2-1
3.0 Instruction for Use
You can download this information from the following websites:
http://www.philips.com/support
http://www.p4c.philips.com
3-1
4.0 MECHANICAL AND DISMANTLING INSTRUCTIONS
The following guidelines show how to dismantle the player.
Step1: Remove 4 screws around the Top Cover, and then remove the Top Cover
4-1
Step3: Remove the 9 screws on board to dismantle the DVD BOARD & PSU BOARD & DECK
Step2: Dismantling Front Panel,the CD door should be removed first, then gently pull the Panel out from the set.
PS: insert reset hole once the disc tray jammed
use an acuate press the reset hole to release the disc tray; remove the door from the tray;
No display on VFD, and buttons do not work
No
No
No
Yes
Yes
No display on VFD, and
buttons do not work
Check every supply
voltage on main board is
normal Refer to Power supply board part
Correct connection
Replace VU1 or VFD
Yes
Go
Yes
No
Check +5V,+12V,-24V
voltage on the power
and front board
SG,GR on the front board
1.Check whether bad solder exists
on VU1 and pins of VFD
2.Check whether the circuit
connected to K1, K2, K3, K4 is
broken.
Fix the connection J3 on front board
and CN4 on power board
Trouble shooting chart
5-1
Check the signals of the VU1's Check the VU1 power supply
(VU1.38= +5V and VU1.27= -24V)
No audio output
Check whether the audio
signal is right from the
U1's pin 8, 9
Correct connection
Yes
Go
No audio output
No
Trouble shooting chart
5-2
exists on pins of J7
Check whether bad solder
Replace the J7
No
Yes
Check the U1 power supply
(U1.1= +3.3V and U1.11= +5V)
Yes
Replace the U1
Remote control does not work
Go
Yes
Yes
Remote control
does not work
NO
Replace the battery for remote
controller
Check whether the remote
controller’s battery is
exhausted or not.
Check the Power supply board part
Replace IR1
NO
Trouble shooting chart
5-3
Check the IR1 power supply is OK
Check the connection J2 on front board
and J502 on main board is broken
Yes
Fix the connection
NO
Yes
Tabla de contenidos
Otros manuales de Reproductor de Blu-ray de Philips
Philips
Philips BDP7600/51 Manual de usuario
Philips
Philips PB9001/12 Manual de usuario
Philips
Philips BDP7100 Manual de usuario
Philips
Philips BDP2900 Manual de usuario
Philips
Philips BDP5502/F8 Manual de usuario
Philips
Philips BDP2205/F7 Manual de usuario
Philips
Philips BDP5010 Manual de usuario
Philips
Philips BDP5150/F7 Manual de usuario
Philips
Philips BDP-2800 Manual de usuario
Philips
Philips BDP5650/93 Manual de usuario
Philips
Philips BDP5110 Manual de usuario
Philips
Philips BDP2100 Manual de usuario
Philips
Philips BDP3010/F7 Manual de usuario
Philips
Philips BDP5500 Manual de usuario
Philips
Philips BDP7700 Manual de usuario
Philips
Philips BDP2600/94 Manual de usuario
Philips
Philips BDP5150/F8 Manual de usuario
Philips
Philips BDP3020 Manual de usuario
Philips
Philips BDP7100 Manual de usuario
Philips
Philips BDP3020 Manual de usuario
