Philips BDP2982/12 Manual de usuario
BDP2980/12/98/05
BDP2982/12
©Copyright 2012 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without
the prior permission of Philips.
Blu-ray Disc Player
Version 1.0Version 0.0
Published BG AVM Printed in The Netherlands Subject to modification 3141 785 37980
TABLE OF CONTENTS
Chapter
Technical Specification, PCBs Location………………….. 1
Safety Instruction ……………………………………………… 2
Instruction for Use………………………………………………3
Mechanical and Dismantling Instructions…………………. 4
Service Modes, Troubleshooting……………………………. 5
Overall Block Diagram, Wiring Diagram…………………….6
Electrical Diagram……………………………………………… 7
Exploded View Diagram & Service Part List………………..8
Revision List……………………………………………………. 9
1.1 Specifications
Specifications are subject to change without notice
1-1
Playable media
- BD-Video, BD 3D
- DVD-Video, DVD+R/+RW, DVD-R/-RW, DVD+R/-R DL (Dual Layer)
- VCD/SVCD
- Audio CD, CD-R/CD-RW, MP3 media, WMA media, JPEG iles
- DivX (Ultra)/DivX Plus HD media, MKV media
- USB storage device
File format
- Video: .avi, .divx, .mp4, .mkv
- Audio: .mp3, .wma, .wav
- Picture: .jpg, .gif, .png
Video
- Signal system: PAL / NTSC
- HDMI output 480i/576i, 480p/576p, 720p, 1080i, 1080p, 1080p/24Hz
Audio
- Digital output: 0.5 Vp-p (75 ohm)
- Coaxial
- HDMI output
- Sampling frequency:
- MP3: 32 kHz, 44.1 kHz, 48 kHz
- WMA: 44.1 kHz, 48 kHz
- Constant bit rate:
- MP3: 112 kbps - 320 kpbs
- WMA: 48 kpbs - 192 kpbs
USB
- Compatibility: Hi-Speed USB (2.0)
- Class support: USB Mass Storage Class
- File system: FAT16, FAT32
- Support HDD (a portable hard drive disc): an external power source may be needed.
Main unit
- Power supply rating: AC 220-240V~, 50Hz - 60Hz BDP2980/12 BDP2982/12
- Power consumption: 11 W
- Power consumption in standby mode: < 1 W
- Dimensions (w x h x d): 310 X 40 X 203 (mm)
- Net Weight: 1.1 kg
Accessories supplied
- Remote control and 2 AAA batteries
- User manual
Laser Specification
- Laser Type (Diode): AlGaInN (BD), AlGaInP (DVD/CD)
- Wave length: 405+7nm/-7nm (BD), 660+4nm/-10nm (DVD), 790+6/-6nm (CD)
- Output power: 1mW (BD), 0.3mW (DVD), 0.28mW (CD)
Optional accessory
- A wireless Philips USB adaptor(named WUB1110,sold separately)
- Multimedia connections:Wi-Fi 802.11b/g/n
- Connectivity: USB
- Ambient temperature:5 degC to 40 degC
- Dongie dimensions (W X H X D):28.4 X 82 X13.4mm
- Power supply rating: AC 110-127V~, 50Hz - 60Hz BDP2980/98
1.1 PCBs Location
VERSION VARIATIONS
Type/Versions:
Service policy
Board in used:
BDP2982/BDP2980
*TIPS: C -- Component Lever Repair.
M -- Module Lever Repair
X -- OCX
1-2
M
12
PSU PCBA
MAIN BOARD
M
PSU PCBA
MAIN BOARD
98
C/M
M
MM
05
Software check and upgrade
Preparation to upgrade software
1)Start the CD burning software & create a folder named "UPG_ALL", B. Read out the software versions to confirm upgrading
2)Then copy the Bin file (BDP3XXXXX-XXX-XXXXXX.bin) into it,
3)Burn the data onto the blank CD.
A. Procedure for software upgrade
A) Upgrade software via Disc
4) In homemenu,enter "setup"->"advanced"->"version info", press "OK"
1) Power on the set and insert the prepared Upgrade
CDR.
and other information will display on the TV screen as below:
2) The set will starts reading disc & response with the Model:XXX.XXX
following display TV screen: Versions
Now searching for upgrade software!
Please wait…!
3) Then screen will display :
software upgrades for this player has been found!Do you want to upgrade? Caution: The set must not be power off during
upgrading, otherwise the Main board will be
Cancel Start damaged entirely.
4) Press Right cursor button to choose "Start", then press <OK>;
5) The software will updagrde and screen will display as below:
Upgrade is ongoing, Please wait…
Please do not unplug or switch off the device.
6) Restart the set.
B) Update software via USB Flash Drive:
1) Go to www.philips.com/support to check if the latest software
version is available for this player.
2) Download the software onto a USB flash drive's root DIR named "UPG_ALL".
3) Insert the power plug and HDMI cable, power on and then insert the USB flash drive to the USB jack.
4) In the Home menu, select <Setup>-<Advanced>-<Software
update>-<USB>.
5) Then press OK
6) you'll see now searching for new software, please wait.......
7) Waiting, the you'll see "software for this player has been found ......"
8) Then select "Start" and press "OK"
9) then you'll see "upgrade is ongoing ......", wait until it ends.
10) Player will restart automatically or press "Restart now" to restart, after restarting the upgrade ends.
subinfo:xxxx
system SW:xxxx
ethernet MAC:xxxxxxxx
http://www.philips.com/support
1-3
Remark: pls. make sure the software can be match with the loader
2.0 Safety instruction
1. General safety
Safety regulations require that during a repair:
. Connect the unit to the mains via an isolation
transformer.
. Replace safety components indicated by the
symbol
Only by components identical to the original ones.
Any
Other component substitution (other than original
type)
May increase risk of fire or electrical shock hazard.
Safety regulations require that after a repair, you
must
Return the unit in its original condition. Pay, in
particular,
Attention to the following points:
. Route the wires/cables correctly, and fix them with
the
mounted cable clamps
. Check the insulation of the mains lead for external
Damage
. Check the electrical DC resistance between the
mains
Plug and the secondary side:
1) Unplug the mains cord, and connect a wire
between
The two pins of the mains plug.
2) Set the mains switch the “on” position (keep
the
Mains cord unplug).
3) Measure the resistance value between the
mains
plug and the front panel, controls, and chassis
bottom.
4) Repair or correct unit when the resistance
measurement is less than 1M Ω
5) Verify this, before you return the unit to the
customer/user (ref. UL-standard no. 1492).
6) Switch the unit “off”, and remove the wire
between
the two pins of the mains plug.
2. Laser safety
This unit employs a laser. Only qualified service
personnel
May remove the cover, or attempt to service this
device
(due to possible eye injury).
Laser device unit
Type :Semiconductor laser GaAIAs
Wavelength :650nm (DVD)
:780nm (VCD/CD)
Output power :7mW(DVD)
:10mW(DVD/CD)
Beam divergence:60 degree
Note: Use of controls or adjustments or
performance of procedure other than those
specified herein, may result in hazardous
radiation exposure. Avoid direct exposure to
beam.
2-1
3.0 Instruction for Use
You can download this information from the following websites:
http://www.philips.com/support
http://www.p4c.philips.com
3-1
4.0 MECHANICAL AND DISMANTLING INSTRUCTIONS
The following guidelines show how to dismantle the player.
Step1: Remove 3 screws around the Top Cover, and then remove the Top Cover
4-1
Step3: Remove the 9 screws on board to dismantle the DVD BOARD & PSU BOARD & DECK
Step2: Dismantling Front Panel,the CD door should be removed first, then gently pull the Panel out from the set.
PS: insert reset hole once the disc tray jammed
use an acuate press the reset hole to release the disc tray; remove the door from the tray;
No display , and buttons do not work
No
No
No
Yes
Yes
No display on LED DISPLAY, and
buttons do not work
Check every supply
voltage on main board is
normal Refer to Power supply board part
Correct connection
Replace PU4 or LED DISPLAY
Yes
Go
Yes
No
Check +5V,+12V,
voltage on the power
board
DATA,CLK,STB,on the power board
1.Check whether bad solder exists
on PU4 and pins of LED DISPLAY
2.Check whether the circuit
connected to PK1, PK2 is broken.
Fix the
power board
Trouble shooting chart
5-1
Check the signals of the PU4's Check the PU4 power supply
(PU4.7= +5V and PU4.21= +5V)
Remote control does not work
Go
Yes
Yes
Remote control
does not work
NO
Replace the battery for remote
controller
Check whether the remote
controller’s battery is
exhausted or not.
Check the Power supply board part
Replace IR1
NO
Trouble shooting chart
5-2
Check the IR1 power supply is OK
Check whether bad solder exits on IR1'pins Yes Fix the connection
NO
Yes
Can’t read disc or can’t open the disk door
Yes
Check the connection of the 16PIN cable
from PJ1 on the Power Board.
Can’t read disc or can’t
open the disk door
Check 40pin and 8pin cable
from main board connection to
the loader is normal
Check the U409 and the peripheral
components near them on the main board
NO
GO
Check whether the
DVD loader running is
normal
Fix the connection
NO
Yes
Trouble shooting chart
5-3
Este manual sirve para los siguientes modelos
3
Otros manuales de Reproductor de Blu-ray de Philips
Philips
Philips BDP2205/F7 Manual de usuario
Philips
Philips BDP7302 Manual de usuario
Philips
Philips BDP3200 Manual de usuario
Philips
Philips BDP3100/12 Manual de usuario
Philips
Philips BDP7100/12 Manual de usuario
Philips
Philips BDP2985/F7 Manual de usuario
Philips
Philips BDP5602 Manual de usuario
Philips
Philips BDP2100/40 Manual de usuario
Philips
Philips BDP5600/05 Manual de usuario
Philips
Philips BDP2900 Manual de usuario
Philips
Philips MBD3000/93 Manual de usuario
Philips
Philips BDP3000 Manual de usuario
Philips
Philips BDP2180/62 Manual de usuario
Philips
Philips BDP9700/51 Manual de usuario
Philips
Philips BDP3000/12 Manual de usuario
Philips
Philips BDP3306/F7 Manual de usuario
Philips
Philips BDP5510 Manual de usuario
Philips
Philips BDP2100 Manual de usuario
Philips
Philips BDP2100/F7 Manual de usuario
Philips
Philips BDP5005 Manual de usuario
