Phase Technologies DV Series Manual de usuario

ii | Page

No portion of this publication or its contents may be duplicated by any means, electronic or otherwise, without the

express written consent of Phase Technologies, LLC.

V0.0_09012022

222 Disk Drive

Rapid City, SD 57701

Phone: 605-343-7934

Fax: 605-343-7943

Toll Free: 866-250-7934

www.phasetechnologies.com

iii | Page

SAFETY MESSAGES AND WARNINGS

To ensure safe and reliable operation of output filters, it is important to carefully read

this manual and to observe all warning labels attached to the unit before installing.

Please follow all instructions exactly and keep this manual with the unit for quick and

easy reference.

Definitions of Warning Signs and Symbols

CAUTION: Indicates a potentially hazardous situation that could result in injury or

damage to the product.

WARNING: Indicates a potentially hazardous situation that could result in serious

injury or death.

HIGH VOLTAGE: The voltage associated with the procedures referenced could

result in serious injury or death. Use caution and follow instructions carefully.

READ THESE WARNINGS BEFORE INSTALLING

OR OPERATING EQUIPMENT!

WARNING: Risk of electric shock. More than one disconnect switch may be

required to de-energize the equipment before servicing.

WARNING: Risk of electric shock. Before servicing the equipment, de-energize

the filter by disconnecting all incoming sources of power, wait 10 minutes for internal

charges to dissipate, and verify with a voltmeter that all power sources are off and

capacitors are discharged. Failure to do so may result in severe injury or death.

HIGH VOLTAGE: This equipment is connected to line voltages that can create a

potentially hazardous situation. Electric shock could result in serious injury or death.

This device should be installed only by trained, licensed, and qualified personnel. Follow

instructions carefully and observe all warnings.

WARNING: This equipment should be installed and serviced by qualified personnel

familiar with the type of equipment and experienced in working with dangerous voltages.

WARNING: Installation of this equipment must comply with the National Electrical

Code (NEC) and all applicable local codes. Failure to observe and comply with these

codes could result in risk of electric shock, fire, or damage to the equipment.

CAUTION: Circuit breakers, fuses, proper ground circuits, and other safety

equipment and their proper installation are not provided by Phase Technologies, LLC,

and are the responsibility of the end user.

iv | Page

CAUTION: Failure to maintain adequate clearance may lead to overheating of the

unit and cause damage or fire.

WARNING: Input power connections should be made by a qualified electrician into

circuit with adequate voltage and current carrying capacity for the model.

CAUTION: Use 600 V vinyl-sheathed wire or equivalent. The voltage drop of the

leads needs to be considered in determining wire size. Voltage drop is dependent on

wire length and gauge. Use only copper conductors.

CAUTION: Wires fastened to the terminal blocks shall be secured by tightening

the terminal screws to a torque value listed in Table 4.

CAUTION: The maximum wire gauge for the input terminals is listed in Table 4.

CAUTION: Never allow bare wire to contact metal surfaces.

CAUTION: For SW filters with internally powered fans, ensure that the variable

frequency drive (VFD) is set to V/f (Volts per Hz) mode. Failure to properly configure

the VFD could result in failure of the VFD or filter components.

CAUTION: Before installation, visually inspect the filter and secure any loose

electrical connections before applying power. Failure to do so may result in damage to

the filter or diminished performance.

v | Page

TABLE OF CONTENTS

INTRODUCTION..................................................................................................... 1

1.1 RECEIVING INSTRUCTIONS .................................................................................. 2

1.2 MODELS AND RATINGS ....................................................................................... 3

RATINGS ................................................................................................................ 5

2.1 PRODUCT SPECIFICATIONS ................................................................................. 5

INSTALLATION...................................................................................................... 7

3.1 MOUNTING YOUR NEW [PRODUCT NAME] FILTER ............................................. 7

3.2 PROPER VENTILATION ........................................................................................ 7

3.3 GROUNDING ...................................................................................................... 7

3.4 WIRE SIZING...................................................................................................... 7

3.5 CONNECTING THE LOAD..................................... ERROR!BOOKMARK NOT DEFINED.

3.6 CONNECTING TO FIELD WIRING TERMINALS ........ ERROR!BOOKMARK NOT DEFINED.

OPERATION.................................................ERROR! BOOKMARK NOT DEFINED.

4.1 COMMISSIONING THE UNIT ................................. ERROR!BOOKMARK NOT DEFINED.

TROUBLESHOOTING ...........................................................................................10

ENCLOSURE DIMENSIONS ........................ERROR! BOOKMARK NOT DEFINED.

WARRANTY ..........................................................................................................13

1 | Page

INTRODUCTION

Output filters are used to remove unwanted high frequency content from the output of a

Variable Frequency Drive (VFD). Large voltage spikes are produced when VFDs are used to

drive motors with long cable leads, which can damage motor or cable insulation systems or

motor bearing fluting due to electric discharge. This voltage spike is known as the Reflected

Wave Phenomenon. dV/dt filters extend motor and cable life by reducing the effects of the

Reflected Wave Phenomenon and removing high frequency voltage spikes. dV/dt filters

should be used when motor cables exceed 50 feet and sine wave filters should be used when

motor cables exceed 900 feet.

For additional protection, sine wave filters provide more robust removal of higher frequency

content. As well as providing protection against voltage spikes from reflected waves, a sine

wave filter additional removes lower order harmonic voltage and currents. These benefits are

realized in reduced motor losses (less heating) due to lower eddy currents and magnetic

hysteresis losses in motor steel laminations.

Figure 1shows an unfiltered VFD output voltage measured line-to-line.

Figure 1– Unfiltered VFD Output Voltage

2 | Page

Figure 2shows output voltage after being filter by the dv series dV/dt filter.

Figure 2– Output Voltage After dv Series dV/dt filter.

Figure 3shows a output voltage after being filtered by the sw series sine wave filter.

Figure 3– Output Voltage After sw Series Sine Wave Filter.

Phase Technologies output filters can be configured in Open, NEMA Type 1, or NEMA Type

3R enclosures. Open filters are intended to be installed in a panel. Type 1 filters come with

an enclosure designed for indoor use only. Type 3R enclosures are made for outdoor use.

Make sure the filter has the proper enclosure type for your application.

1.1 Receiving Instructions

Phase Technologies sine wave filters are thoroughly inspected and tested before packaging

for shipment. Upon receiving the unit, immediately inspect it for any damage that may have

occurred during shipping. If any damage is found, contact the Phase Technologies’ service

3 | Page

department at (605) 343-7934. Loose electrical connections can also cause damage to the

filter or diminish its performance. Visually inspect the filter and tighten any loose connections

found.

1.2 Nomenclature

1.3 Models and Ratings

Table 1– dV/dt Filter Ratings

Model

Rated Current (A)

DV009E

DV013E

7.5

DV018E

DV031E

DV045E

DV060E

DV077E

DV090E

DV107E

107

DV128E

100

128

DV160E

125

160

DV200E

150

200

DV250E

200

250

DV362E

300

362

DV480E

400

480

Table 2– Sine Wave Filter Ratings

Model

Rated Current (A)

SW009E

SW013E

7.5

4 | Page

SW018E

SW031E

SW045E

SW060E

SW077E

SW090E

SW107E

107

SW128E

100

128

SW160E

125

160

SW200E

150

200

SW250E

200

250

SW362E

300

362

SW480E

400

480

5 | Page

RATINGS

2.1 Product Specifications

Table 3 –General Specifications, dv Series Filters

dV/dt Filter

Input Voltage Waveform PWM

VFD Output Voltage ≤ 480 VAC, 3-phase

VFD Output Frequency ≤ 90 Hz

VFD Switching Frequency 2 kHz – 10 kHz

Current Range 9 – 480 A

Maximum Motor Lead Length 1,000 feet

Max Peak Voltage

150% of DC bus voltage

up to 1,000 feet

Max dV/dt at Motor ≤200V/µs

Insertion Loss (Voltage)

≤1% at 60Hz

≤1.5% at 90Hz

Efficiency ≥ 99%

Enclosure Options

Open, NEMA 1, or

NEMA 3R

Operating Temperature

-20 °C to 40 °C

(-4 °F to 104 °F)

Storage Temperature

-25 °C – 74 °C

(-13 °F – 165 °F)

Maximum Humidity 95%, non-condensing

Elevation

Derate by 5 °C for every

2,000 feet over 5,500 feet

of elevation

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Sistema de filtración de agua de otras marcas

Wisy

Wisy LineAir 100 Manual de usuario

Schaffner

Schaffner Ecosine FN3446 Series Manual de funcionamiento

Pentair

Pentair FLECK 4600 SXT Guía del usuario

H2O International

H2O International H20-500 Manual de usuario

Renkforce

Renkforce 2306241 Manual de usuario

Neo-Pure

Neo-Pure TL3-A502 Manual de usuario

FLTR

FLTR OBF Manual de usuario

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manual de usuario

Applied Membranes

Applied Membranes W-G844EM Manual de usuario

BEGA

BEGA 116 Manual de usuario

WATA

WATA Standard Manual de usuario

Price

Price FFU series Manual

Gaggenau

Gaggenau BRITA INTENZA 467873 Manual de usuario

Brita

Brita SAFF-100 Manual de usuario

HEISSNER

HEISSNER FPU24000-00 Manual de usuario

BGS technic

BGS technic 1518 Manual de usuario

Reverse Osmosis

Reverse Osmosis RF Series Manual de usuario

ubbink

ubbink Filtramax Series Manual de usuario