PEWA Amprobe LAN-1 Manual de usuario

LAN-1

Lan Cable Tester

Users Manual

Mode d’emploi•

Bedienungshandbuch•

Manuale d’Uso•

Manual de uso•

Användarhandbok•

English

LAN-1

Lan Cable Tester

Users Manual

LAN1_Rev001

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material and workmanship for

1 year from the date of purchase. This warranty does not cover fuses, disposable

batteries or damage from accident, neglect, misuse, alteration, contamination,

or abnormal conditions of operation or handling. Resellers are not authorized

to extend any other warranty on Amprobe’s behalf. To obtain service during the

warranty period, return the product with proof of purchase to an authorized

Amprobe Test Tools Service Center or to an Amprobe dealer or distributor. See

Repair Section for details. THIS WARRANTY IS YOUR ONLY REMEDY. ALL OTHER

WARRANTIES - WHETHER EXPRESS, IMPLIED OR STAUTORY - INCLUDING IMPLIED

WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY,

ARE HEREBY DISCLAIMED. MANUFACTURER SHALL NOT BE LIABLE FOR ANY

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES,

ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do not

allow the exclusion or limitation of an implied warranty or of incidental or

consequential damages, this limitation of liability may not apply to you.

Repair

All test tools returned for warranty or non-warranty repair or for calibration

should be accompanied by the following: your name, company’s name, address,

telephone number, and proof of purchase. Additionally, please include a brief

description of the problem or the service requested and include the test leads

with the meter. Non-warranty repair or replacement charges should be remitted

in the form of a check, a money order, credit card with expiration date, or a

purchase order made payable to Amprobe® Test Tools.

*(Correspondence only – no repair or replacement available from this address.

European customers please contact your distributor.)

➊RJ45 jack for sourcing end

(OUT).

➋RJ45 jack for receiving end (IN).

➌

LED indicators for sourcing end

(OUT) Green.

➍LED indicators for receiving end

(IN). Red.

➎AUTO scan button.

➏TEST button for MANUal test.

➐POWER ON/OFF button.

➑BATTery TEST button.

➒HOLD button.

➓MANUal scan button.

Low BATTery indicator.

Remote Terminator LED

indicator for ground wire

Remote Terminator LED

indicators for data lines

Remote Terminator RJ45 jack

HOLD

MAN

AUTO

TEST

BATT

REMOTE

TERMINATOR

IN OUT

1 2 3 4 5 6 7 8 G

OUT

GRD

LAN-1

Lan cable tester

CONTENTS

Symbols..................................................................................................................5

Unpacking and Inspection....................................................................................5

Introduction...........................................................................................................5

Operation ..............................................................................................................6

Loopback Test (cable with both ends in one location)..................................6

Remote Test (cable with both ends at different locations)...........................6

Hold ..................................................................................................................6

Test Examples ........................................................................................................7

Speciﬁcations.........................................................................................................7

Maintenance and Repair .....................................................................................8

Battery Replacement ............................................................................................8

SYMBOLS

Refer to the manual Do not dispose of this

product as unsorted

municipal waste.

Conforms to relevant

Australian standards. Complies with EU

directives



This equipment not

for connection to

public communications

networks, such as active

telephone systems.

Warning and Precautions

DO NOT use on live circuits. These voltage levels pose a potential shock•

hazard to the user.

To avoid electrical shock hazard, observe the proper safety precautions•

when working with voltages above 60 VDC or 30 VAC rms.

Never ground yourself when taking measurements.•

Do not operate the instrument in an explosive atmosphere.•

To reduce the risk of ﬁre or electric shock, do not expose this product to•

rain or moisture.

UNPACKING AND INSPECTION

Your shipping carton should include:

1 LAN-1 Cable tester

1 Remote Terminator

1 9 volt battery

1 RJ45 to female BNC cable

1 RJ45 to male BNC cable

1 RJ45 to RJ45 cable

1 female BNC to female BNC connector

1 Users Manual

If any of the items are damaged or missing, return the complete package to

the place of purchase for an exchange.

INTRODUCTION

The LAN-1 Cable Tester is designed for testing opens, shorts and miswired

cable installations .

Testing capabilities are:

Test pin conﬁguration for 10/100 base -T cable, 10 base-2 cable, RJ45•

modular cables, AT&T 258A cable, EIA / TIA 568A/568B cables and Token

Ring Cable etc.

Verify cable continuity, open, short or incorrectly wired.•

Test installed cable on wall plate or the patch panels by using the Remote•

Termination module.

Buzzer sound warning for error condition.•

OPERATION

Press1. button for power ON. If no cable is attached or cable is defective,

the buzzer will sound.

Press BATT to verify proper operating voltage. The BATT LED will not light2.

and LAN-1 will not operate correctly if battery is below 7 volts.

Green LEDs are the source indicators. Red LED’s are the test indicators.3.

Red LED’s ON indicate cable line continuity. Red LED’s OFF indicate open

cable lines.

Loopback Test (cable with both ends in one location)

Connect cable with RJ-45 terminations on both ends to IN and OUT test1.

sockets.

Press2. button for power ON. Press AUTO (default) or MAN button to

start scanning.

AUTO scanning will step through lines 1 to 8 and ground (if connected)3.

and repeats until stopped.

MAN scanning will go into manual mode and TEST will step through the4.

different lines.

Remote Test (cable with both ends at different locations)

Connect one cable end to OUT connector.1.

Connect REMOTE TERMINATOR to the other end of cable under test.2.

Press3. button for power ON. Press AUTO (default) or MAN button to

start scanning.

AUTO scanning will step through lines 1 to 8 and ground (if connected)4.

and repeat until stopped.

MAN scanning go into manual mode and TEST will step through the5.

different lines.

Line test results (Red LED’s) are shown on the Remote Terminator.6.

Hold

The HOLD button saves the displayed error condition and stops testing. Press

the HOLD button to return to normal operation.

TEST EXAMPLES

Continuity Green onooooooo

Pin 2 has continuity 1 2 3 4 5 6 7 8 G

Red onooooooo

Open Green onooooooo

Pin 2 is open 1 2 3 4 5 6 7 8 G

Red ooooooooo

Short Green onnoooooo

Pins 2 and 3 are shorted 1 2 3 4 5 6 7 8 G

Red onnoooooo

Miswire Green onooooooo

Pins 2 and 6 are miswired 1 2 3 4 5 6 7 8 G

Red ooooonooo

SPECIFICATIONS

General

Display: Red and Green LED’s

Battery: 9V, 006P or IEC 6F22 or NEDA 1604.

Low Battery Indicator: The LED indicator will not turn ON when

BATT button pushed

Battery Life: Approx 20 hours. (Alkaline battery)

Environment: Indoor operation, maximum altitude

- 2000 m (6561 ft.)

Temperature / Humidity:

Operation: 0 to 40°C (32 to 104°F), 10 to 70% RH.

Storage: -10 to 60°C (14 to 140°F), 10 to 90% RH.

Dimension: 130 x 64 x 38mm (5.1 x 2.2 x 1.5 in)

Weight: 1.26 kg (0.6 lb)

-EMC: EN61326-1 This product complies with requirements of the

following European Community Directives: 89/336/EEC (Electromagnetic

Compatibility) and 73/23/EEC (Low Voltage) as amended by 93/68/EEC (CE

Marking). However, electrical noise or intense electromagnetic ﬁelds in the

vicinity of the equipment may disturb the measurement circuit. Measuring

instruments will also respond to unwanted signals that may be present within

the measurement circuit. Users should exercise care and take appropriate

precautions to avoid misleading results when making measurements in the

presence of electronic interference.

Electrical

Maximum line length: ~300 meters

Connector types: RJ45, BNC

DO NOT use on live circuits.

MAINTENANCE AND REPAIR

If there appears to be a malfunction during the operation of the tester, the

following steps should be performed in order to isolate the cause of the

problem.

Press the BATTery button to check the battery. Replace the battery1.

immediately if the LED indicator will not turn ON.

Review the operating instructions for possible mistakes in operating2.

procedure.

Except for the replacement of the battery, repair of the meter should be

performed only by a Factory Authorized Service Center or by other qualiﬁed

instrument service personnel. The front panel and case can be cleaned with

a mild solution of detergent and water. Apply sparingly with a soft cloth and

allow to dry completely before using. Do not use aromatic hydrocarbons or

chlorinated solvents for cleaning.

BATTERY REPLACEMENT

1. Turn off the meter and slide out the battery cover. Replace the battery with

a NEDA type 1604 or equivalent 9V alkaline battery. Replace the cover.

2. Remove battery when the LAN-1 is not used for extended period.

OPEN

Battery Replacement

LAN1_Rev001

LAN-1

Testeur de câbles LAN

Mode d’emploi

Français

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Equipo de prueba de PEWA

PEWA

PEWA Megger PCITS600/2 Manual de usuario

PEWA

PEWA ROBIN AMPROBE KMP 7036 Manual de usuario

PEWA

PEWA AMPROBE digital Manual de usuario

PEWA

PEWA BEHA UNITEST TELARIS SCHLEIFE Manual de usuario

PEWA

PEWA VOLTfix Series Manual de usuario

PEWA

PEWA ODEN AT Manual de usuario

PEWA

PEWA Chauvin Arnoux C.A 6423 Manual de usuario

PEWA

PEWA Metrel MD 1100-LCD Manual de usuario

PEWA

PEWA Robin-Amprobe KMP7030 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario