PerTronix Ignitor Manual de usuario
LIMITED WARRANTY
PerTronix, Inc. warrants to the original Purchaser of its solid-state
ignition system (product) that the Ignitor shall be free from defects in material
and workmanship for a period of (30) months from the date of purchase.
If within the period of the foregoing warranty PerTronix finds, after inspec-
tion, that the product or any component thereof is defective, PerTronix will, at
its option, repair such products or component or replace them with identical
or similar parts PROVIDED that within such period Purchaser:
1. Promptly notifies PerTronix, in writing, of such defects.
2. Delivers the defective products product or component to PerTronix
(Attn: Warranty) with proof of purchase date; and
3. Has installed and used the product in a normal and proper
manner, consistent with PerTronix printed instructions
THE FOREGOING LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU
OF ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED,
INCLUDING ANY IMPLIED WARRANTY OR MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
THE FURNISHING OF A REPAIR OR REPLACEMENT COMPONENTS
SHALL CONSTITUTE THE SOLE REMEDY OF PURCHASER AND THE
SOLE LIABILITY OF PerTronix WHETHER ON WARRANTY, CONTRACT
OR FOR NEGLIGENCE, AND IN NO EVENT WILL PerTronix BE LIABLE
FOR MONEY DAMAGES WHETHER DIRECT OR CONSEQUENTIAL.
440 East Arrow Highway
San Dimas, California 91773
(909) 599-5955
INSTALLATION INSTRUCTIONS FOR
12 VOLT POSITIVE GROUND APPLICATIONS
For 12-volt positive ground systems.
Compatible with “points style” coils.
Do not use “HEI” type coils.
Read all instructions before attempting to install...
1. Turn the ignition switch off or disconnect the battery.
2. Remove the distributor cap and rotor. Do not disconnect the sparkplug wires.
3. Examine the cap and rotor for wear or damage. Replace as needed.
4. Remove the points, condenser, and grommet.
5. The Ignitor does not require any modification to the distributor. Therefore
the points, condenser and hardware can be used as backup.
6. Clean any oil or dirt from the breaker plate and point cam.
7. Install the Ignitor plate onto the breaker plate, and fasten it in place.
8. If the distributor ground wire was removed during the installation process,
be sure to re-attach it securely.
9. Install the magnet sleeve over distributor shaft and onto the point cam.
Rotate sleeve until a slight locating position is felt before applying
pressure. With sleeve lined up on point cam, press down firmly insuring
the sleeve is fully seated.
10. Insert both wires through the hole in the distributor housing. Pull the
grommet into place. Make sure that the wires do not interfere with any
moving parts.
11. Replace the rotor and distributor cap. Make sure that all spark plug wires
are attached securely.
12. Remove the ignition switch wire from the negative coil terminal. Connect
the black Ignitor wire directly to the ignition switch wire.
13. Connect the Ignitor black/white wire to negative (-) side of the ignition coil.
14. Connect an insulated, AWG 20 copper stranded wire from the positive coil
terminal to the positive battery or chassis.
15. The black/white Ignitor wire and the AWG 20 copper wire should be the
only wires connected to the coil.
16. Reconnect the battery and make sure all wires are connected correctly.
17. The engine can now be started. Let the engine run for a few minutes and
then set the timing in the conventional manner.
0000 008796 12/01
WIRING DIAGRAM FOR SYSTEMS
WITHOUT BALLAST RESISTORS
Q. What is the first thing I should check if the engine would not start?
A. Make certain all wires are connected securely to the proper terminals.
Q. What type of coil can I use?
A. The Ignitor™ is compatible only with a "points style" coil.
Q. What happens if I leave the ignition switch on when the engine is not
running?
A. This can cause you coil to overheat, which may cause permanent damage to the coil and the
Ignitor™.
Q. May I modify the length of the Ignitor™ wires?
A. Yes, you may cut the wires to any length your application may require. You may also add
lengths of wire if needed (20 gauge wire). Please make sure all wire splice are clean and
connections are secure.
Q. How can I get additional help?
A. Call our tech line (800 827 3758) for any further instructions or questions. You may also
logon to www.pertronix.com for the latest technical information.
Ignitor™ COMMON QUESTIONS AND ANSWERS
Otros manuales de Otro de PerTronix
