Performax 241-0988 Manual de usuario

OPERATING MANUAL

Reciprocating Saw

241-0988

IMPORTANT:

Read through this operating manual carefully before using this tool. Pay close

attention to all Safety Instructions, Warnings, and Caution sections. Use this tool

properly and only for its intended use.

Safety symbols in this manual are used to call attention to possible dangers.

The safety symbols and their explanations require the operator’s full understand-

ing. The safety warnings do not, by themselves, eliminate any danger, nor are

they a substitute for proper accident-prevention measures.

This Safety Alert Symbol indicates caution, warning, or danger. Failure to

obey a safety warning can result in serious injury to the operator or to others.

To reduce the risk of injury, ﬁre, or electric shock, always follow the safety pre-

cautions.

TABLE OF CONTENTS

Speciﬁcations……………..……………………………………….......Page 2

Safety Symbols…..…………………………………….….....................Page 3

Rules for Safe Operation…..…………………………………….….......Page 4

Description……………..………………………………………............Page 9

Assembly and Adjustment…………….…………………………..……Page 10

Operation……………..……………………………………….........…Page 12

Maintenance……………..…………………………………….....……Page 14

Warranty……………..………………………………………..........…Page 15

SPECIFICATIONS

Motor: 120V 60Hz 8.5A

Variable Speed: 0–2,700 SPM (no load)

Blade stroke: 1-1/8” (28.6 mm)

Cutting Capacity: Metal: 5/8” (15.9mm)

Wood: 6” (152.4mm)

Weight: 7 lbs (3.2kg)

SAFTEY SYMBOLS

The purpose of safety symbols is to attract your attention to possible dangers.

The safety symbols and the explanations with them deserve your careful attention

and understanding. The symbol warnings do not, by themselves eliminate any

danger. The instructions and warnings they give are no substitutes for proper

accident prevention measures.

WARNING: Be sure to read and understand all safety instructions in this

manual, including all safety alert symbols such as “DANGER,” ”WARNING” and

“CAUTION,” before using this reciprocating saw. Failure to follow all instructions

listed below may result in electric shock, ﬁre and/or serious personal injury

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation,

which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a potentially hazardous situation,

which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates an potentially hazardous situation,

which, if not avoided, may result in minor or

moderate injury.

NOTE: (Without SafetyAlert Symbol) Indicates a situation

that may result in property damage.

WARNING:

To ensure safety and reliability, all repairs should be performed by

a qualiﬁed service technician at Authorized Service Center.

WARNING: The operation of any power tool can result in

foreign objects being thrown into your eyes, which can

result in severe eye damage. Before beginning power

tool operation, always wear safety goggles or safety

glasses with side shields and a full-face shield when

needed. We recommend a Wide Vision Safety Mask for

use over eyeglasses or standard safety glasses with

side shields. Always use eye protection which is marked

to comply with ANSI Z87.1

SAFETY SYMBOLS FOR YOUR TOOL

RULES FOR SAFE OPERATION

KNOW THE TOOL

To operate this tool, carefully read this Owner’s Manual and all labels afﬁxed to

the saw before using. Keep this Manual available for future reference.

IMPORTANT

This tool should only be serviced by a qualiﬁed service technician. For more

information, call the toll-free helpline, 1-866-858-2664.

GENERAL SAFETY RULES FOR ALL POWER TOOLS

Warning: Read and understand all instructions. Failure to follow all in-

structions listed below may result in electric shock, ﬁre and/or serious personal

injury.

SAVE THESE INSTRUCTIONS.

WORK AREA

Keep your work area clean and well lit. Cluttered benches and dark areas

invite accidents.

Do not operate power tools in explosive atmospheres, such as in the

presence of ﬂammable liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

Keep bystanders, children, and visitors away while operating a power

tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Double insulated tools are equipped with

a polarized plug (one blade is wider than

the other). This plug will ﬁt in a polarized

outlet only one way. If the plug does not ﬁt

fully in the outlet, reverse the plug. If it still

does not ﬁt, contact a qualiﬁed electrician

to install a polarized outlet. Do not change

the plug in any way. Double insulation

eliminates the need for the three wire

grounded power cord and grounded power

supply system.

Avoid body contact with grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your

body is grounded.

Don’t expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord to carry the tool or to pull

the plug from an outlet. Keep the cord away from heat, oil, sharp edges

or moving parts. Replace damaged cords immediately. Damaged cords

increase the risk of electric shock.

When operating a power tool outside, use an outdoor extension cord

marked “W-A” or “W”. These cords are rated for outdoor use and reduce the

risk of electric shock.

PERSONAL SAFETY

Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use the tool while tired or under the

inﬂuence of drugs, alcohol, or medication. A moment of inattention while

operating power tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose

clothes, jewelry, or long hair can be caught in moving parts.

Avoid accidental starting. Be sure that the switch is off before plugging

in the tool. Carrying tools with your ﬁnger on the switch or plugging in tools

that have the switch on invites accidents.

Remove adjusting keys or wrenches before turning the tool on. A wrench

or a key that is left attached to a rotating part of the tool may result in personal

injury.

120V~ ,60Hz

Do not overreach. Keep proper footing and balance at all times.

Proper footing and balance enable better control of the tool in unexpected

situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid

safety shoes, hard hat, or hearing protection must be used for appropriate

conditions.

Before connecting the tool to a power source (receptacle, outlet, etc.),

be sure that the voltage supplied is the same as that speciﬁed on

the nameplate of the tool. A power source with voltage greater than that

speciﬁed for the tool can result in serious injury to the user – as well as

damage to the tool.

Tool Use and Care

Use clamps or another practical way to support and secure the workpiece

to a stable platform. Holding the work by hand or against your body is

unstable and may lead to loss of control.

Do not force the tool. Use the correct tool for your application. The correct

tool will do the job better and more safely at the rate for which is designed.

Do not use the tool if the switch does not turn it on or off. Any tool that

cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source before making any

adjustments, changing accessories, or storing the tool. Such preventive

safety measures reduce the risk of starting the tool accidentally.

Store idle tools out of reach of children and other untrained persons.

Tools are dangerous in the hands of untrained users.

Maintain tools with care. Keep cutting tools sharp and clean. Properly

maintained tools with sharp cutting edges are less likely to bind and are easier

to control.

Check for misalignment or binding of moving parts, breakage of parts,

and any other condition that may affect the tools operation. If damaged,

have the tool serviced before using. Many accidents are caused by poorly

maintained tools.

Use only accessories that are recommended by the manufacturer for

your model. Accessories that may be suitable for one tool, may become

hazardous when used on another tool.

Do not alter or misuse tool. These tools are precision built. Any alteration or

modiﬁcation not speciﬁed is misuse and may result in a dangerous condition.

SERvICE

Tool service must be performed only by qualiﬁed repair personnel.

Service or maintenance performed by unqualiﬁed personnel could result in

a risk of injury.

When servicing a tool, use only identical replacement parts. Follow

instructions in the Maintenance section of this manual. Use of unauthorized

parts or failure to follow Maintenance instructions may create a risk of electric

shock or injury.

SPECIFIC SAFETY RULES FOR RECIPROCATING SAW

Hold the tool by insulated gripping surfaces when performing an

operation where the cutting tool may contact hidden wiring or its own

cord. Contact with a “live” wire will make exposed metal parts of the tool

“live” and shock the operator.

Secure material before cutting. Never hold the material you are cutting in

your hand or across legs. Small pieces or thin material may ﬂex or vibrate with

the blade, causing loss of control.

Obtain advice from a qualiﬁed person if the operator is not thoroughly

familiar with the operation of a reciprocating saw.

The reciprocating saw is double insulated. When servicing, use only

identical replacement parts.

Avoid cutting nails when using the wood blade. Inspect the workpiece

carefully and remove all nails and staples before cutting.

Verify that the blade always extends beyond the shoe and the workpiece

throughout the stroke. Blades may shatter if they strike the workpiece or the

shoe.

Do not cut oversized workpieces.

Check for proper clearance beyond the workpiece before cutting, so that the

blade will not strike the ﬂoor, the workbench, etc.

Verify that the blade is not in contact with the workpiece before the switch

is turned on.

Keep the saw blades clean and sharp.

Use only correct blades. Always use blades that are recommended for the

material and type of workpiece being cut.

Do not leave the tool running. This tool is only intended to be operated when

hand held.

Turn the switch to the OFF position and wait for the tool to come to a

complete stop before removing the blade from the workpiece.

Keep the handle dry, clean, and free of oil and grease. Always use a

clean cloth when cleaning. Do not use solvents, brake ﬂuids, gasoline or

other petroleum products to clean the tool, because they may damage plastic

parts.

Do not force the tool. Apply ﬁrm pressure against the saw pivot shoe for the

sawing operation. Too little pressure or too much pressure may cause jumping

and vibration, and may break the blade.

Do not operate the saw without the pivot shoe in position. The spindle

may strike against the workpiece and damage the reciprocating mechanism.

Do not touch the blade or the workpiece immediately after the sawing

operation. It may be extremely hot, and could burn your skin.

Keep hands away from cutting area. Do not reach under the material being

cut. The proximity of the blade to your hand is hidden from your sight.

Always wear safety goggles or eye protection when using this tool. Use

a dust mask or respirator or connect the tool with an external dust vacuum if

the cutting generates a great amount of dust.

DESCRIPTION

KNOW YOUR RECIPROCATING SAW (Fig. 1)

Before attempting to use this reciprocating saw, familiarize yourself with all of its

operating features and safety requirements.

WARNING: Do not allow familiarity with your reciprocating saw to make you

careless. Remember that a careless fraction of a second is sufﬁcient enough to

inﬂict severe injury.

1. Pivoting Shoe Plate

2. Front Grip

3. Variable Speed Trigger Switch

4. Blade Clamp Release Lever

WARNING: To avoid injury and damage, do not operate the saw without the

pivot shoe in place. The spindle may strike against the workpiece and damage

the reciprocating mechanism.

Fig.1

ASSEMBLY AND ADJUSTMENT

Remove the reciprocating saw from the carton and inspect it carefully. Do not

discard the carton or any packaging material until all parts have been inspected.

WARNING: If any part of the saw is missing or damaged, do not plug the re-

ciprocating saw in until the damaged part is repaired or replaced.

WARNING: To avoid injury, ALWAYS turn the switch OFF and disconnect the

reciprocating saw from the outlet before installing or changing the saw blade.

ON/OFF SWITCH AND VARIABLE SPEED CONTROL (Fig. 2)

This reciprocating saw is equipped with

a trigger On/Off switch that allows the

operator to turn the saw on and off and to

control the speed

1. To start the saw, squeeze the trigger

switch.

2. To stop the saw, release the trigger

switch and allow it to return to the OFF

position.

3. To vary the speed, simply increase or decrease the pressure on the trigger

switch. The more tightly the trigger switch is squeezed, the higher the

speed.

INSTALLING AND REMOVING BLADES

1. Disconnect the saw from the power

source.

2. Push the blade clamp release lever

down with one thumb.

3. Insert the blade into the slot of the tool-

less blade clamp. (see Fig. 3)

4. Release the blade clamp release lever

to lock the blade.

WARNING: When changing a blade immediately after operation, allow the

blade to cool before removing in order to avoid possible burns.

WARNING: Test to make sure the blade was clamped securely.

Fig. 2

Fig. 3

Tabla de contenidos

Otros manuales de Sierra de Performax

Performax

Performax 240-3605 Manual de usuario

Performax

Performax 240-3724 Manual de uso y cuidado

Performax

Performax 241-0944 Manual de usuario

Performax

Performax 241-0951 Manual de usuario

Performax

Performax 90235 Manual de usuario

Performax

Performax 241-0987 Manual de usuario

Performax

Performax 241-0995 Manual de usuario

Performax

Performax 240-3756 Manual de usuario

Performax

Performax 241-0968 Manual de usuario

Performax

Performax 240-3687 Manual de usuario

Performax

Performax 240-3600 Manual de usuario

Performax

Performax 241-0985 Manual de usuario

Performax

Performax 9'' Band Saw Manual de usuario

Performax

Performax 241-0950 Manual de usuario

Performax

Performax 240-3690 Manual de usuario

Performax

Performax 240-3669 Manual de usuario

Performax

Performax 241-0932 Manual de usuario

Performax

Performax 240-3680 Manual de usuario

Performax

Performax 240-3688 Manual de usuario

Performax

Performax COMPACT PX12 LITHIUM-ION Manual de usuario

Performax

Performax 241-0991 Manual de usuario

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario