Peak Scientific MS Bench Series Manual de usuario

MS Bench (All Models) User Manual Rev 6 RSID 3023 EN 31/03/20

MS Bench (All Models)

User Manual

Contents

Change History 3

How to use this Manual 3

Intended Use of Equipment 3

Warranties and Liabilities 4

Safety Notices 5

Symbols 5

Safety Notice to Users 5

Weight Loading & Stability 6

Declaration of Conformity 7

Environmental Declaration 8

Technical Speciﬁcation 9

Technical Speciﬁcation 10

Unpacking 11

Fittings Kit Contents 12

Installation 13

Generator Environment 13

Generator Overview 14

General Dimensions SCI 1, G SCI 1 and G SCI 2 14

General Dimensions SCI 2 14

MS Bench G SCI 1 Rear Connections 15

MS Bench G SCI 1 Unit Controls 15

MS Bench SCI 1 Rear Connections 16

MS Bench SCI 1 Unit Controls 16

MS Bench G SCI 2 Rear Connections 17

MS Bench G SCI 2 Unit Controls 17

MS Bench SCI 2 Rear Connections 18

MS Bench SCI 2 Unit Controls 18

Drain Connection (MS Bench G SCI 1 & G SCI 2 Only) 19

Electrical Connection 20

Start-Up Sequence (MS Bench G SCI 1 & G SCI 2 Only) 21

Connecting to the application (MS Bench G SCI 1 & G SCI 2 Only) 22

Tubing Lengths 22

Normal Operation (MS Bench G SCI 1 & G SCI 2 Only) 23

On Demand Gas (MS Bench G SCI 1 & G SCI 2 Only) 23

Generator Cycling (MS Bench G SCI 1 & G SCI 2 Only) 23

Unusual Operation (MS Bench G SCI 1 & G SCI 2 Only) 23

Fan Power LED (MS Bench SCI 1 & SCI 2 Only) 24

Safe Operation of Pump Tray (MS Bench SCI 1 Only) 25

Safe Operation of Pump Tray (MS Bench SCI 2 Only) 26

Service Requirements (MS Bench G SCI 1) 27

Service Schedule 27

Service Requirements (MS Bench G SCI 2) 27

Service Schedule 27

Service Indication (MS Bench G SCI 1 & G SCI 2) 28

Stage 1 28

Stage 2 28

Service Indication Reset 28

Peak Protected 29

Cleaning 30

Troubleshooting (MS Bench G SCI 1 & G SCI 2) 31

Page 2

Page 3

Change History

Rev Comment Name Date

1 Initial Release L. Couttie 06/06/2019

2 CSA Feedback Updates L. Couttie 20/06/2019

3 Weight Loading Update L. Couttie 26/06/2019

4 MS Bench G SCI 22 & SCI 2 models added L. Couttie 28/10/2019

5 CSA Feedback Updates L. Couttie 02/12/2019

6 SCIEX Feedback Updates L. Couttie 31/03/2020

How to use this Manual

This manual is intended for end users and has been written as a reference document

where you can skip to the relevant information.

Users can refer to the contents page to ﬁnd the relevant information.

Please review each of the following sections carefully.

Thank you for selecting Peak Scientiﬁc to meet your gas generation needs, and should

you require any further assistance or support please do not hesitate to contact Peak

Scientiﬁc or the Peak Partner from which you purchased your generator.

Intended Use of Equipment

MS Bench SCI 1, is a support cabinet with in-built cooling provided by fans, its top

surface and slide out tray are available for use by the customer as required for their

planned application.

MS Bench G SCI 1 is a support cabinet with an in-built Nitrogen generator. Its top

surface and internal storage space are available for use by the customer as required.

The inbuilt generator provides an output of both compressed air and nitrogen for

supply to customer application on demand via its compressors.

MS Bench SCI 2 is a support cabinet with two internal compartments, one containing

inbuilt cooling provided by fans and a slide out tray, the other open for a larger

roughing pump. The top surface is available for the customer to use for their planned

application.

MS Bench G SCI 2 is a support cabinet with an in-built nitrogen generator, with higher

gas ﬂows than the G SCI 1. The top surface is available for the customer to use for their

planned application.

Page 4

Warranties and Liabilities

1. The Company warrants that it has title to the Goods.

2. Subject to the provisions of this clause the Company warrants that the Goods

shall comply in all material respects with any speciﬁcation referred to in the Order

Conﬁrmation (as the same may be amended) and shall, subject thereto, be free

from defects in material and workmanship for the lesser of a period of twelve

months from the date of delivery or thirteen months from the date of dispatch

from the factory.

3. Save as provided in this clause and except where the Goods are sold to a person

dealing as a consumer (within the meaning of the Unfair Contract Terms Act

1977) all warranties, conditions or other terms implied by statute or common

law are hereby expressly excluded save to the extent they may not be lawfully

excluded. When the Goods are sold to a consumer within the meaning of the Unfair

Contract Terms Act 1977 their statutory rights are not aected by the provisions of

this clause.

4. In the event of the Customer making a claim in respect of any defect in terms of

clause 2 hereof the Customer must.

1. Reasonably satisfy the Company that the Goods have been properly installed,

commissioned, stored, serviced and used and without prejudice to the generality

of the foregoing that any defect is not the direct or indirect result of lack of repair

and/or servicing, incorrect repair and/or servicing, use of wrong materials and/or

incorrect spare parts

2. Allow the company to inspect the Goods and/or any installation and any relevant

packaging as and when reasonably required by the Company.

5. Subject to the Company being notiﬁed of any defect as is referred to in sub-

clause 2 hereof within a reasonable time of it becoming apparent and subject always

to the terms of sub-clause 4 hereof, the Company shall, in its option, replace or

repair the defective Goods or refund a proportionate part of the Price. The Company

shall have no further liability to the Customer (save as mentioned in sub-clause 6

hereof).

6. The Company shall be liable to indemnify the Customer in respect of any claim

for death or personal injury to any person in so far as such is attributable to the

negligence or breach of duty of the Company or any failure by the Company to

comply with the provisions of sub-clause 2 hereof.

7. Save as provided in sub-clause 2 hereof the Company shall not be liable in respect

of any claim by the Customer for costs, damages, loss or expenses (whether direct,

indirect, consequential or otherwise) or indemnity in any respect howsoever arising

including, but not by way of limitation, liability arising in negligence (other than

pursuant to clause 6 above) that may be suered by the Customer or any third

party.

WARNING

CAUTION

Page 5

WARNING

Safety Notices

Peak Scientiﬁc Instruments cannot anticipate every possible circumstance which may

represent a potential hazard. The warnings detailed within this manual refer to the most

likely potential hazards, but by deﬁnition cannot be all inclusive. If the user employs

an operating procedure, item of equipment or a method of working which is not

speciﬁcally recommended by Peak Scientiﬁc, the user must ensure that the equipment

will not be damaged or become hazardous to persons or property.

Symbols

This manual uses the following symbols to highlight speciﬁc areas important to the safe

and proper use of the generator.

A WARNING notice denotes a hazard. It calls attention to an operating procedure,

process or similar, which if not correctly performed or adhered to, could cause

personal injury or in the worst case death. Do not proceed beyond a WARNING

notice until the indicated conditions are fully understood or met.

A CAUTION notice denotes a hazard. It calls attention to an operating procedure,

process or similar, which if not correctly performed or adhered to, could cause

damage to the generator or the application. Do not proceed beyond a CAUTION

notice until the indicated conditions are fully understood or met.

Caution, risk of electric shock. Ensure power to the generator has been removed

before proceeding.

Safety Notice to Users

These instructions must be read thoroughly and understood before

installation and operation of your Peak Generator. Use of the generator

in a manner not speciﬁed by Peak Scientiﬁc MAY impair the SAFETY

provided by the equipment.

When handling, operating or carrying out any maintenance, personnel

must employ safe engineering practices and observe all relevant local

health and safety requirements and regulations. The attention of UK

users is drawn to the Health and Safety at Work Act 1974, and the

Institute of Electrical Engineers regulations.

If the equipment is used in a manner not speciﬁed by the manufacturer,

the protection provided by the equipment maybe impaired.

Page 6

CAUTION

Weight Loading & Stability

Additional weight added to product either on top surface or within cabinet must not

exceed the following maximum combined total:

MS Bench SCI 1 : 272 Kg

MS Bench G SCI 1: 215 Kg

MS Bench SCI 2 : 272 Kg

MS Bench G SCI 2: 206 Kg

Failure to adhere to these values could lead to injury and or damage to

the equipment.

Ensure placement of additional equipment / weight on top surface or with in cabinet

does not cause overall Bench to become unstable, either in use or when sliding tray is

extended and loaded on MS Bench SCI 1 and SCI 2.

Failure to ensure overall product is stable could lead to injury and or

damage to the equipment.

CAUTION

Page 7

Declaration of Conformity

We Peak Scientiﬁc Instruments Ltd.

Of Fountain Crescent, Inchinnan, Renfrewshire, PA4 9RE

Declare that:

Equipment: Bench and Nitrogen Generator Bench

Models: MS Bench SCI 1, MS Bench G SCI 1, MS Bench SCI 2 &

MS Bench G SCI 2

To which this declaration relates, is in conformity with the applicable EC directives,

harmonized standards, and other normative requirements.

• Low Voltage Directive 2014/35/EU

EN 61010-1: 2010 Safety Requirements for Electrical Equipment for Measurement,

Control and Laboratory Use.

• Electromagnetic Compatibility Directive 2014/30/EU

EN 61326-1: 2013 Electrical Equipment for Measurement, Control and Laboratory Use

- EMC Requirements.

• FCC47 CFR Part 15 Class B

Unintentional radiators; Conducted and Radiated emissions limits.

All evaluation, testing and certiﬁcation issued by:

Nemko Canada Inc. Peak Scientiﬁc Instruments Ltd.

303 River Road Fountain Crescent, Inchinnan Business Park

Ottawa, Ontario Inchinnan, Renfrewshire, U.K.

Canada, K1V 1H2 PA4 9RE

Signed: Name: Chris Pugh

Date: 10/06/2019 Position: Engineering Director

Page 8

Environmental Declaration

We Peak Scientiﬁc Instruments Ltd.

Of Fountain Crescent, Inchinnan, Renfrewshire, PA4 9RE

Declare that:

Equipment: Bench and Nitrogen Generator Bench

Models: MS Bench SCI 1, MS Bench G SCI 1, MS Bench SCI 2 &

MS Bench G SCI 2

Is fully compliant with the following Directives.

• 2012/19/EU WEEE (Waste of Electrical and Electronic Equipment)

• 2011/65/EU & 2015/863 RoHS (Restriction of Hazardous Substance)

Peak Scientiﬁc Instruments Ltd fully complies with its obligations towards the European

WEEE (Waste of Electrical and Electronic Equipment) Directive 2012/19/EU. These

obligations are being met within the B2B compliance group.

Peak Scientiﬁc Instruments Ltd, herewith conﬁrm that as a manufacturer of articles we

conform to the European Parliament and Council Directives, 2011/65/EU for the original

6 restricted substances listed in the Restriction of Hazardous Substances (RoHS)

Directive and Commision Delegated Directive (EU) 2015/863 to include 4 additional

restricted substances. Peak Scientiﬁc Instruments LTD have developed all reasonable

'due diligence' controls to ensure that our products comply with the principles and

requirements of the RoHS (Restriction of Hazardous Substances) Directives.

Where a speciﬁc certiﬁcate of compliance is required, this can be requested, on

a product serial number basis, directly from Peak Scientiﬁc Instruments Ltd, by

contacting us through our website at www.peakscientific.com

Signed: Name: Chris Pugh

Date: 10/06/2019 Position: Engineering Director

Page 9

Technical Specification

Environment

MS Bench SCI 1 MS Bench G SCI 1

Minimum Operating Ambient Temperature 5°C (41°F)

Maximum Operating Ambient Temperature 30°C (86°F)

Maximum Altitude 2000 m

Maximum Relative Humidity 80% Non-Condensing

Minimum Storage Temperature* -20°C (-4°F)

Maximum Storage Temperature* 60°C (140°F)

*NOTE – Storage below 5°C (41°F) for long periods is not recommended. When taken out of storage the Generator

should be allowed to acclimatize at room temperature for a minimum of 3 hours before operation.

Generator Outlets

Curtain Maximum Flow^

N/A

19 L/min @ 4.48 bar (0.670

cfm @ 65 psi)

Source Maximum Flow^ 26 L/min @ 6.89 bar (0.918

cfm @ 100 psi)

Exhaust Maximum Flow^ 25 L/min @ 4.13 bar (0.882

cfm @ 60 psi)

Particles <0.01µm

Phthalates NONE

Suspended Liquids NONE

Gas Outlets 3 x ¼” BSPP

Drain Outlet 1 x ¼” BSPP

^NOTE – These performance characteristics are valid only when paired with an approved Sciex application. Please refer

to current application matrix for a list of supported products.

Electrical Requirements

Voltage 100 - 240v ±10% 220 - 240v ±10%

Frequency 50/60 Hz

Current 2 Amps 6 Amps

Input Connection C20 Plug

Power Cord (Supplied) C19 socket to local connection (13A minimum)

Pollution Degree 2

Installation / Over Voltage Category II

General

Dimensions cm (inches) WxDxH 91.4 x 78.7 x 76.2 (36 x 31 x 30)

Generator Weight Kg (lbs) 103 (227.1) 160 (352.8)

Shipping Weight Kg (lbs) 118 (260.2) 175 (385.9)

Page 10

Technical Specification

Environment

MS Bench SCI 2 MS Bench G SCI 2

Minimum Operating Ambient Temperature 5°C (41°F)

Maximum Operating Ambient Temperature 30°C (86°F)

Maximum Altitude 2000 m

Maximum Relative Humidity 80% Non-Condensing

Minimum Storage Temperature* -20°C (-4°F)

Maximum Storage Temperature* 60°C (140°F)

*NOTE – Storage below 5°C (41°F) for long periods is not recommended. When taken out of storage the Generator

should be allowed to acclimatize at room temperature for a minimum of 3 hours before operation.

Generator Outlets

Curtain Maximum Flow^

N/A

25 L/min @ 4.48 bar (0.882

cfm @ 65 psi)

Source Maximum Flow^ 26 L/min @ 6.89 bar (0.918

cfm @ 100 psi)

Exhaust Maximum Flow^ 25 L/min @ 4.13 bar (0.882

cfm @ 60 psi)

Particles <0.01µm

Phthalates NONE

Suspended Liquids NONE

Gas Outlets 3 x 5/16” BSPP

Drain Outlet 1 x ¼” BSPP

^NOTE – These performance characteristics are valid only when paired with an approved Sciex application. Please refer

to current application matrix for a list of supported products.

Electrical Requirements

Voltage 100 - 240v ±10% 220 - 240v ±10%

Frequency 50/60 Hz

Current 2 Amps 9 Amps

Input Connection C20 Plug

Power Cord (Supplied) C19 socket to local connection (13A minimum)

Pollution Degree 2

Installation / Over Voltage Category II

General

Dimensions cm (inches) WxDxH 104 x 78.7 x 76.2 (41 x 31 x 30) 91.4 x 78.7 x 76.2 (36 x 31 x 30)

Generator Weight Kg (lbs) 103 (227.1) 169 (372.5)

Shipping Weight Kg (lbs) 118 (260.2) 184 (405.6)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de laboratorio de Peak Scientific

Peak Scientific

Peak Scientific Halo Manual de usuario

Peak Scientific

Peak Scientific Solaris 10 Manual de usuario

Peak Scientific

Peak Scientific Solaris XE Manual de usuario

Peak Scientific

Peak Scientific Genius SQ 24 Manual de usuario

Peak Scientific

Peak Scientific Genius 3010 Manual de usuario

Peak Scientific

Peak Scientific Horizen 24 Manual de usuario

Peak Scientific

Peak Scientific Genius XE Series Manual de usuario

Peak Scientific

Peak Scientific MS Table Series Manual de usuario

Peak Scientific

Peak Scientific MS Table Series Manual de usuario

Peak Scientific

Peak Scientific Zero Air ZA015 Manual de usuario

Peak Scientific

Peak Scientific Precision Zero Air Series Manual de usuario

Peak Scientific

Peak Scientific Precision Hydrogen Manual de usuario

Peak Scientific

Peak Scientific MS Bench Manual de usuario

Peak Scientific

Peak Scientific Precision SL A5 Instrucciones de funcionamiento

Peak Scientific

Peak Scientific Genius XE QSD Manual de usuario

Peak Scientific

Peak Scientific Genius XE Series Manual de usuario

Peak Scientific

Peak Scientific TOC 1500 Manual de usuario

Peak Scientific

Peak Scientific Corona CA Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario