PEACOCK CIRRUS Manual de usuario
Before you begin, read these instructions completely and carefully.
• Be certain electrical power is OFF before and during installation, maintenance and removal.
• Fan wiring must be properly grounded in accordance with the NEC and any applicable local code requirements.
• Use only UL or IEC approved wire for input/output connections.
• Verify that supply voltage matches voltage on fan label. Installation to any other connection may void the warranty.
• Wear gloves during installation to prevent injury and do not expose wiring to metal or sharp edges.
IMPORTANT SAFETY PRECAUTIONS
WARNING: To reduce the risk of fire, electrical shock, or personal injury, mount this fan to an outlet box marked "Acceptable for Fan Support of
22.7kg (50lbs)" or less and use Mounting Screws provided with the outlet box. CAUTION: Install the primary mounting means and use only the
hardware provided with the fan.
To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or clearing the fan. Be
careful not to insert foreign objects in between rotating fan blades.
To reduce the risk of fire or electrical shock, do not use this fan with any solid-state speed control device.
The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur.
It must be understood that common sense, caution and careful attention to detail are factors which cannot be built into this product. These
factors must be supplied by the person or persons installing, caring for, and operating the unit.
This product should be installed, inspected and maintained by a qualified and licensed electrician. Installation of luminaire must be in accordance
with NEC and local code requirements.
ELECTRIC SHOCK FALLING PARTS
ABRASIONS BURNS
CIRRUS CEILING FAN
Installation Manual
REV 2022 1018
SPECIFICATIONS AND DETAILS ARE SUBJECT TO CHANGE WITHOUT NOTIFICATION. CONTACT PEACOCK FAN COMPANY FOR UP TO DATE DETAILS.
PEACOCK FAN COMPANY • PEACOCKFAN.COM
SAVE THESE INSTRUCTIONS 1
CIRRUS CEILING FAN
Installation Manual
REV 2022 1018
SPECIFICATIONS AND DETAILS ARE SUBJECT TO CHANGE WITHOUT NOTIFICATION. CONTACT PEACOCK FAN COMPANY FOR UP TO DATE DETAILS.
PEACOCK FAN COMPANY • PEACOCKFAN.COM
SAVE THESE INSTRUCTIONS 2
No. NAME QUANTITY
1Hanger Bracket 1
2Downrod 1
3Blade Holder 6
4Canopy 1
5Decorative Cover 1
6Motor Body 1
7Remote Control 1
8Bottom Cover 1
9Blade 6
10 Fasteners Package 1
11 Balance Package 1
12 Blade Screws 19
DIMENSIONS
TOOLS REQUIRED
PACKAGE PARTS
119.7”
6.7”
4.7”
5.9”
2.4”
• Phillips screwdriver
• Flat head screwdriver
• Adjustable pliers or wrench
• Step ladder
• Wire cutters
• Electrical tape
• Impact drill
3
1
2
5
9
4
10
11
6
7
812
M5 M8
4
3
6
1
25
1H 8H4H
DIMENSIONS
TOOLS REQUIRED
PACKAGE PARTS
119.7”
6.7”
4.7”
5.9”
2.4”
• Phillips screwdriver
• Flat head screwdriver
• Adjustable pliers or wrench
• Step ladder
• Wire cutters
• Electrical tape
• Impact drill
12
11
10
9
85
7
6
4
1
2
3
CIRRUS CEILING FAN
Installation Manual
REV 2022 1018
SPECIFICATIONS AND DETAILS ARE SUBJECT TO CHANGE WITHOUT NOTIFICATION. CONTACT PEACOCK FAN COMPANY FOR UP TO DATE DETAILS.
PEACOCK FAN COMPANY • PEACOCKFAN.COM
SAVE THESE INSTRUCTIONS 3
INSTALL THE HANGER
A) Secure the hanger bracket to the steel
bracket on ceiling with M5 or M8 mounting
screws and nuts. (See Figure 1)
INSTALLATION OF DOWNROD AND MOTOR BODY
A) First remove the safety pins on the
connection head, and then remove the two
fixed downrod pipe screws located in the
connection head on top of the motor body.
(See Figure 2);
B) Orient and insert the downrod pipe in
the right direction through the canopy and
decorative cover and then thread the power
wires through the downrod pipe;
C) Insert the downrod pipe into the connec-
tion head and install the safety pins, then
lock the fixed downrod pipe screws firmly
and cover the connection head with the
decorative cover.
A) Place the drop ball in the hanger bracket
and turn the pipe so that the groove on the
drop ball engages the slot on the hanger
bracket. The drop ball groove must engage
the hanger bracket slot. (See Figure 4 and 5)
B) Replacing the downrod pipe (if
applicable): first remove 2 screws, then
remove the horizontal pin, then replace the
standard downrod with the desired downrod
pipe, then reinsert the horizontal pin, and
lock the 2 screws. (See Figure 6)
HANGING THE CEILING FAN
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4 FIGURE 5 FIGURE 6
Hanger Bracket
Connection Head
Connection Head
Downrod
Downrod
Hanger
Bracket Slot
Groove
Screws
Pin
Drop Ball
Drop
Ball
Hanger
Bracket
Canopy
Decorative Cover
Safety Pins
Safety Pins
Motor Body
Downrod Pipe Screws Downrod
Pipe Screws
M5 or M8 mounting screw
Lift the ball
Steel bracket
CIRRUS CEILING FAN
Installation Manual
REV 2022 1018
SPECIFICATIONS AND DETAILS ARE SUBJECT TO CHANGE WITHOUT NOTIFICATION. CONTACT PEACOCK FAN COMPANY FOR UP TO DATE DETAILS.
PEACOCK FAN COMPANY • PEACOCKFAN.COM
SAVE THESE INSTRUCTIONS 4
HANGING THE CEILING FAN (CONTINUED)
C) Put the end of the steel cable through
the holes of the cable grip lock and form a
small loop of suitable size. Then tighten the
cable grip lock screws to lock the cable. Use
a screw with a metal washer through the
cable loop and secure it to the steel bracket
on ceiling. (See Figure 7)
D) After ensuring the correct wiring (See
Figure 12), insert the receiver into the hanger
bracket as shown in Figure 8 and 9, install
the canopy by covering the hanger bracket
(Figure 10) and securing it with screws
(Figure 11).
WIRING DIAGRAM INSTALL THE FAN BLADE AND BLADE HOLDER
A) Attach each fan blade to a blade arm with three blade screws and three nuts. (See
Figure 13)
B) Attach each blade to the motor body using mounting screws. (See Figure 14)
All screws and nuts for assembling blades and attaching to motor body must be
tightened with wrench.
INSTALL BOTTOM COVER
A) Tighten the bottom cover in a clockwise direction.
FIGURE 7
FIGURE 8
FIGURE 10
FIGURE 9
FIGURE 11
FIGURE 12
FIGURE 13
FIGURE 14
FIGURE 15
Screws
Downrod
Canopy
Canopy Screws
Downrod
Hanger
Bracket
Hanger
Bracket
Hanger
Bracket
Metal Washer
WHITE
WHITE BLUE
BLUE
WHITE
BLACK
BLACK
RED or BLACK
ANT
Cable Grip Lock
Receiver
Steel Cable
Steel Bracket
Downrod
Canopy
Motor Body
Receiver
Decorative Cover
CIRRUS CEILING FAN
Installation Manual
REV 2022 1018
SPECIFICATIONS AND DETAILS ARE SUBJECT TO CHANGE WITHOUT NOTIFICATION. CONTACT PEACOCK FAN COMPANY FOR UP TO DATE DETAILS.
PEACOCK FAN COMPANY • PEACOCKFAN.COM
SAVE THESE INSTRUCTIONS 5
INSTALLATION HEIGHT
BALANCE ADJUSTMENT OF THE FAN
TIPS: MAINTENANCE OF CEILING FANS
Fan blades to the ground shall not be less than 7.6 feet.
If the fan is shaking up and down after installation, please check the screws on the blades and downrod to ensure they are secure and tight. If not, tighten with screw driver or
wrench. If it still shakes, please use the balancing kit and check the instruction of balancing kit inside the carton.
• Check regularly whether the hanger, fan blade, and other parts are loose, if not, please tighten any loose fasteners to ensure it runs safely.
• Clean regularly. Only use a soft brush or a lint-free cloth to clean. Do not use a damp cloth or other destructive cleaner.
• Don't add lubricating oil or lubricant to any part of this fan.
1.6 ft
7.6 ft
Tabla de contenidos
Otros manuales de Admirador de PEACOCK
