PDi WaveStar Manual de instrucciones

WaveStar®

Color Monitor

Setup and Operation

Ctrl Nr: PM375103

Revision: 003

WaveStar Color Monitor ___________________________________________________________

Ctrl Nr: PM375103 Revision: 003 2

Thank you for your recent purchase of a WaveStar®Color Monitor from Power Distribution, Inc.

For safety reasons as well as to ensure optimal performance of your WaveStar®Color Monitor, please

carefully read the instructions before trying to install, operate, service or maintain the system.

For any questions regarding the installation, operation, service or maintenance of your WaveStar®

Color Monitor, please contact us:

Power Distribution, Inc. | 4200 Oakleys Court | Richmond, VA 23223

+1 804 737 9880 | +1.800.225.4838

pdicorp.com | service@pdicorp.com

WaveStar® Color Monitor

Setup and Operation

Ctrl Nr: PM375103 Revision: 003

Release Date: December 2017

Cover Photo: WaveStar® Color Monitor Home Screen

PDI, JCOMM, Quad-Wye, ToughRail Technology, and WaveStar are registered trademarks of Power

Distribution Inc. All other trademarks are held by their respective owners.

Power Distribution, Inc. (PDI)

Power Distribution, Inc. (PDI) designs, manufactures, and services mission critical power distribution, static switches, and

power monitoring equipment for corporate data centers, alternative energy, industrial and commercial customers around the

world. For over 30 years, PDI has served the data center and alternative energy markets providing flexible solutions with the

widest range of products in the industry.

Contents________________________________________________________________________ 
 Ctrl Nr: PM375103 Revision: 003 3 
Contents
Safety ............................................................................................6 
1Introduction..........................................................................7 
1 WaveStar Color Monitor Summary....................................................... 7 
2 Power On and Access......................................................................... 7 
3 Screen Summary and Navigation ........................................................ 8 
4 Entering Data ................................................................................... 8 
2Color Monitor Networking ...................................................10 
1 Supported Protocols ........................................................................ 10 
2 Monitor Network Connections ........................................................... 10 
2.1 Modbus RTU Ports................................................................. 11 
2.2 Modbus RTU 2-Wire vs. 4-Wire Configuration ........................... 11 
3 Modbus RTU Cables ......................................................................... 12 
3.1 Cable Specification................................................................ 12 
3.2 Cable Biasing and Termination................................................ 12 
4 Ethernet Cables .............................................................................. 12 
5 Customer Modbus RTU Connections ................................................... 12 
5.1 Power Distribution Unit (PDU)................................................. 13 
5.1 Remote Power Panel (RPP)..................................................... 14 
5.1 JCOMM ................................................................................ 14 
6 Modbus Addressing ......................................................................... 15 
7 Communicating with the Monitor: Commands and Replies .................... 16 
7.1 Modbus Commands and Replies.............................................. 16 
7.2 Limit on Open Sockets........................................................... 16 
7.3 SNMP Commands.................................................................. 16 
3Setup: Monitor and Network ...............................................17 
1 SETUP: Miscellaneous Parameters ..................................................... 17 
2 Network Setup................................................................................ 18 
2.1 Downstream Modbus Device Chain Setup................................. 18 
2.2 Modbus RTU Setup................................................................ 18 
2.3 TCP/IP and Modbus TCP/IP Setup ........................................... 19 
2.4 SNMP Setup ......................................................................... 19 
2.5 Loading INI Parameters from an SD Card................................. 20 
3 Software Versions ........................................................................... 20 
4Device Chain: Settings ........................................................22 
1 Initial Device Chain ......................................................................... 22 
2 Device Settings............................................................................... 23 

WaveStar Color Monitor ___________________________________________________________ 
 Ctrl Nr: PM375103 Revision: 003 4 
4.2.1 PDU Device Settings.............................................................. 23 
4.2.2 Enhanced Subfeeds Settings .................................................. 24 
4.2.3 BCMS Normal and KWH Settings............................................. 24 
4.2.4 BCMS CB Subfeeds Settings ................................................... 25 
4.2.5 BCMS IEC Settings................................................................ 26 
5Device Chain: Readings .......................................................27 
5.1 PDU Device Readings....................................................................... 27 
5.2 Enhanced Subfeeds (ESF) Readings................................................... 28 
5.3 BCMS (Normal) Panelboard Readings................................................. 30 
5.4 BCMS KWH Readings ....................................................................... 31 
5.5 BCMS CB (Subfeeds) Readings.......................................................... 33 
5.6 BCMS IEC Readings ......................................................................... 33 
6Alarms and Troubleshooting ...............................................35 
6.1 Summary Alarm Indicators ............................................................... 35 
6.2 Alarm Screen and Alarm List............................................................. 35 
6.3 Alarms by Device Type..................................................................... 37 
6.3.1 Color Monitor Alarms............................................................. 37 
6.3.2 PDU Alarms.......................................................................... 37 
6.3.3 Enhanced Subfeeds ............................................................... 39 
6.3.4 BCMS Panelboard—Typical Alarms .......................................... 40 
6.4 Troubleshooting .............................................................................. 40 
7Web Pages ..........................................................................42 
Glossary ......................................................................................46 
Bibliography ................................................................................47 
Appendix: Color Monitor Backpanel .............................................48 
 
Tables 
Table 1 Pin-Out for Modbus Headers ...................................................................................................11 
 
Figures 
Figure 1 WaveStar Color Monitor Installed in a JCOMM........................................................................7 
Figure 2 HOME Screen and Navigation Buttons ....................................................................................8 
Figure 3 Entering Alphanumeric Data.....................................................................................................9 
Figure 4 Color Monitor Network Connections.......................................................................................10 
Figure 5 Color Monitor 4-wire Modbus Connections ............................................................................12 
Figure 6 Modbus RTU Connections: PDU Basic Contractor Board .....................................................13 
Figure 7 Modbus RTU Connections: PDU Enhanced Contractor Board..............................................13 
Figure 8 Modbus RTU Customer Connection: RPP Upstream.............................................................14 

Contents________________________________________________________________________ 
 Ctrl Nr: PM375103 Revision: 003 5 
Figure 9 JCOMM Modbus Connections................................................................................................14 
Figure 10 Modbus Addressing..............................................................................................................15 
Figure 11 SETUP Screen......................................................................................................................17 
Figure 12 Calibrating the Touchscreen.................................................................................................17 
Figure 13 Modbus RTU Setup ..............................................................................................................18 
Figure 14 Modbus TCP/IP and SNMP Setup........................................................................................19 
Figure 15 Model Information.................................................................................................................20 
Figure 16 Initial Device List...................................................................................................................22 
Figure 17 Settings: PDU Device ...........................................................................................................23 
Figure 18 Settings: Enhanced Subfeeds (ESF)....................................................................................24 
Figure 19 Settings: BCMS Device ........................................................................................................25 
Figure 20 Settings: BCMS Subfeeds ....................................................................................................25 
Figure 21 Settings: BCMS IEC .............................................................................................................26 
Figure 22 Readings: PDU.....................................................................................................................27 
Figure 23 Readings: Enhanced Subfeeds (ESF) (Part 1).....................................................................28 
Figure 24 Readings: Enhanced Subfeeds (ESF) (Part 2).....................................................................29 
Figure 25 Readings: BCMS (Normal) ...................................................................................................30 
Figure 26 Readings: BCMS KWH (Part 1)............................................................................................31 
Figure 27 Readings: BCMS KWH (Part 2)............................................................................................32 
Figure 28 Readings: BCMS CB (Two Subfeeds)..................................................................................33 
Figure 29 Readings: BCMS IEC Panelboard........................................................................................34 
Figure 30 Alarm and Warning Summary Status Icons..........................................................................35 
Figure 31 ALARM Screen with an Alarm List........................................................................................36 
Figure 32 Find the Circuits in an Alarm Condition ................................................................................36 
Figure 33 Web Pages: Home Page ......................................................................................................42 
Figure 34 Web Pages: Device Chain....................................................................................................42 
Figure 35 Web Pages: Display Device .................................................................................................43 
Figure 36 Web Pages: PDU Board.......................................................................................................44 
Figure 37 Web Pages: Enhanced Subfeeds.........................................................................................45 
Figure 38 Color Monitor Backpanel ......................................................................................................48 
 

Safety __________________________________________________________________________

Ctrl Nr: PM375103 Revision: 003 6

Safety

Please pay special attention to the use of “Danger” symbols throughout this manual indicating

electrical or other safety hazards. Following these safety instructions is extremely important to avoid

possible injury or death.

Follow safe electrical work practices:

•Read, understand, and follow the instructions before installing this product.

•Electrical equipment should be installed, operated, serviced, and maintained only by

qualified personnel and in accordance with all local safety codes. Power Distribution,

Inc. assumes no responsibility for any consequences arising out of the use of this

manual. This document should not be viewed as sufficient by otherwise non-qualified

personnel to operate, service, or maintain the equipment discussed.

•Disconnect and lock-out all power supplying equipment before working on or

installing WaveStar®Color Monitor components. Use a properly rated voltage sensing

device to confirm power is OFF.

•Install device in an appropriate electrical enclosure per local regulations.

•ESD sensitive equipment. Ground yourself, discharge any static charge and ensure

that the device is effectively grounded before handling the unit.

The WaveStar®Color Monitor must be installed by licensed electricians or

by PDI-authorized technicians.

DANGER!

Severe or fatal injury can result from electrical shock during contact with high

voltage conductors, monitoring PCBs, or similar equipment.

Disconnect power before drilling holes, attaching conduit, and attaching WaveStar®

Color Monitors to PDUs, RPPs, or other power distribution equipment.

Use Lock Out/Tag Out procedures.

Wear suitable personal protective clothing and use protective equipment for

performing mechanical and electrical installations.

Leave ample space for attaching and routing wires.

Introduction_______________________________________________________________________

Ctrl Nr: PM375103 Revision: 003 7

1Introduction

1.1 WaveStar Color Monitor Summary

The WaveStar®Color Monitor is a 7-inch color touchscreen which displays power management

information for up to twenty (20) Branch Circuit Monitoring System (BCMS) devices and other PDI

devices in the Monitor’s downstream Modbus network.

The Color Monitor is incorporated into PDI products, such as PDUs, RPPs, or JCOMM®s, and can

also function as a stand-alone power monitoring station.

Figure 1 shows the Monitor used in a JCOMM®.

Figure 1 WaveStar Color Monitor Installed in a JCOMM

1.2 Power On and Access

The Color Monitor does not have an on/off switch. The Monitor automatically powers-on whenever

power is applied to the unit in which it is installed.

When the unit is powered on for the first time, the Home Screen appears (Figure 2).

The Color Monitor is accessed by touching the screen. If the unit is powered up and is not touched for

15 minutes, the backlight will turn off to save power. The backlight turns back on when the operator

again touches the screen, showing the last displayed screen.

WaveStar Color Monitor_____________________________________________________________

Ctrl Nr: PM375103 Revision: 003 8

1.3 Screen Summary and Navigation

Setup and configuration information for the Color Monitor are on these screens:

•SETUP: system parameters, such as number of devices in Monitor’s chain

•Device SETTINGS: Device-specific parameters, such as user-specified device name

(DEVICES Device Name SETTINGS)

•SOFTWARE VERSIONS: a list of software versions for each device, accessible only from

the HOME screen.

•DEVICES screen gives a list of all devices in the Monitor’s chain.

•Device SETTINGS screen lets you set device name and parameters specific to the

device.

Setpoints in the device’s points list, such as breaker alarm thresholds, are not viewable or modifiable

on the Monitor.

Power monitoring information as it is stored in each device’s points list (or Modbus register map) is in

each DEVICE READINGS screen.

Alarms and warnings are displayed on these screens:

•ALARM: List of all extant warnings and alarms by device name

•All screens: Warning and alarm summary counts

HELP screen contains Modbus information.

1.4 Entering Data

When you touch a field that requires alphanumeric data, such as device names, passwords, or

version numbers, a touchscreen keyboard will appear, prompting you for information based on

context. You can toggle between LETTERS and SYMBOLS keyboards, for entering text or numbers

(Figure 3).

•The main navigation buttons are present on each screen.

•Touch a button to select that screen.

•

Button turns blue when selected.

Banner, user-specified on SETUP screen

SOFTWARE

VERSIONS button is

only displayed on the

HOME

screen.

Date/Time

Alarm summaries are

given on each page.

Figure 2 HOME Screen and Navigation Buttons

Introduction_____________________________________________________________________

Ctrl Nr: PM375103 Revision: 003 9

Touch here to toggle between Symbol and Letters keyboards as you enter model

information.

Touch

ENTER

to complete the operation. Touch

Cancel

to terminate the operation.

Figure 3 Entering Alphanumeric Data

WaveStar Color Monitor_____________________________________________________________

Ctrl Nr: PM375103 Revision: 003 10

2Color Monitor Networking

2.1 Supported Protocols

All protocols supported by the Color Monitor can be used simultaneously.

Downstream Protocol The downstream device network has fixed parameters of Modbus RTU, 9600

baud, EVEN parity.

Upstream Protocols There are separate upstream ports for Modbus RTU and Ethernet, supporting

these protocols:

•Modbus RTU

•Ethernet port

•TCP/IP, used by the web page server (see Chapter 7, Web Pages)

•Modbus TCP/IP

•SNMP Version 1

2.2 Monitor Network Connections

The Color Monitor’s backpanel has Modbus RTU and Ethernet ports (Figure 4).

For Color Monitors embedded in PDI products (PDUs, RPPs, or JCOMMs), Modbus RTU backpanel

connections are typically made in manufacturing and extended to a terminal block or external panel

for convenient customer access. See 2.5 Customer Modbus RTU Connections.

The customer’s Ethernet cable is connected directly to the Monitor’s Ethernet port.

J2: Modbus RTU

Upstream

RJ12 Connection

(to PDU M4G Board)

J4: Modbus RTU

Downstream

RJ12 Connection

(to PDU M4G Board)

J1: Modbus RTU

Upstream

Connection (except

PDU M4G Board)

J3: Modbus RTU

Downstream

Connection (except

PDU M4G Board)

Ethernet Port

Jumper W1, W2 for

2-wire Modbus upstream

Jumper W3, W4 for

2-wire Modbus

downstream

Figure 4 Color Monitor Network Connections

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Monitor de PDi

PDi

PDi PDI-P19A Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación