PDi PDI-P23LCD Manual de usuario

Owner’

s Manual

Model:

PDI-P23LCD

23" WIDE HOSPI

AL GRADE LCD TV

Document Number PD196-086 Rev 2

nings

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION :

To reduce the risk of electric shock do not remove

cover (or back). No user serviceable parts inside. Refer servicing

to qualified service personnel.

This symbol is intended to alert the user of the presence of uninsulated

‘dangerous voltage’ within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user of the presence of important

operating and maintenance (servicing) instructions in the literature

accompanying the appliance.

NOTE TO CABLE TV INSTALLER

This reminder is provided to call the cable TV systems installer’s attention

to Article 820-40 of the National Electrical Code. The code provides

guidelines for proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the building, as

close to the point of the cable entry as practical.

MAINTENANCE AND SERVICING

Never remove the back cover of the TV; this can expose you to high

voltage and other hazards. If the TV does not operate properly, unplug it

and call an authorized service center or PDI .

CLEANING AND DISINFECTION

Clean the exterior of this television by removing dust with a lint-free

cloth. CAUTION: To avoid damage to the surface of the television, do

not use abrasive or chemical cleaning agents.

RAIN AND MOISTURE

WARNING: To avoid the hazards of fire or electrical shock, DO NOT

expose this television to rain or moisture.

OXYGEN ENVIRONMENT

WARNING: Do not use in any oxygen tent or oxygen chamber. Such use

may cause a fire hazard.

WET LOCATION

Apparatus shall not be exposed to dripping or splashing and no objects

filled with liquids, such as vases, shall be placed on the apparatus.

Document Number PD196-086 Rev 2

nings

SERVICE INSTRUCTIONS

CAUTION: These servicing instructions are for use by qualified service personnel

only. To reduce the risk of electric shock, do not perform any servicing other than

contained in the operating instructions unless you are qualified to do so.

PRODUCT MODIFICATION

Do not attempt to modify this product in any way without written authorization.

Unauthorized modification could void the user’s authority to operate this product.

POWER

This television operates from nominal 115 Volt AC line voltage. Do not attempt to

power this TV using a coaxial cable that carries low voltage power as damage may

result to the TV. Never remove the back cover of the TV; this can expose you to high

voltage and other hazards. If the TV does not operate properly, unplug it and call an

authorized service center or PDI.

REGULATORY INFORMATION

FCC

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a residential or commercial installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one of more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Underwriters Laboratories

The model PDI-P23LCD Hospital Grade LCD TV is a specialized LCD television. This

TV is intended for entertainment and educational purposes for use in a hospital, a

nursing home, a medical-care center, or a similar health-care facility in which

installation is limited to a non-hazardous area in accordance with the National

Electrical Code, ANSI/NFPA70.

This device is safety tested and listed by the Underwriters

Laboratories as a

product suitable for use in health care

facilities in both the United States and

Canada.

Document Number PD196-086 Rev 2

IMPOR

ANT SAFETY INSTR

UCTIONS

11. Only use attachments/accessories

specified by the manufacturer.

12. Use only with the

cart, stand, tripod,

bracket or table

specified by the

manufacturer, or

sold with the

apparatus. When

a cart is used, use

caution when

moving the

cart/apparatus

combination to

avoid injury from

tip-over.

PORTABLE

CART WARNING

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near

water.

6. Clean only with dry cloth.

7. Do no block any ventilation

openings. Install in accordance with

the manufacturer’s instructions.

8. Do not install near any heat source

such as radiators, heat registers,

stove, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of

the hospital grounding-type plug. A

hospital plug has two blades and a

third grounding prong. The third

prong is provided for your safety. If

the provided plug does not fit into

your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being

walked on or pinched particularly at

plugs, convenience receptacles, and

the point where they exit from the

apparatus.

13. Unplug this apparatus during lightning

storms or when unused for long period of

time.

14. Refer all servicing to qualified service

personnel. Servicing is required when

the apparatus has been damaged in any

way, such as power-supply cord or plug

is damaged, liquid has been spilled or

objects have fallen into the apparatus,

the apparatus has been exposed to rain

or moisture, does not operate normally,

or has been dropped.

PDI Communication Systems, Inc. claims proprietary right to the material disclosed in this user

manual. This manual is issued for user information only and may not be used to manufacture

anything

DISCLAIMER

The author and publisher have used their best efforts in preparing this manual. PDI Communication

Systems, Inc. makes no representation or warranties with respect to the accuracy or completeness of

the contents of this manual and specifically disclaims any implied warranties or merchantability or

fitness for any particular purpose and shall in no event be liable for any loss of profit or any other

damages. The information contained herein is believed accurate, but is not warranted, and is

subject to

change without notice or obligation.

TRADEMARKS

All brand names and product names used in this manual are trademarks, registered trademarks, or

trade names of their respective holder. PDI and Better Solutions Are Within Reach are registered

trademarks of PDI Communication Systems, Inc., Springboro, Ohio.

Document Number PD196-086 Rev 2

Contents

Warnings 2,3 Parental Control 24

Important Safety Instructions 4 TV Rating 25

Contents 5 MPAA Rating 25

Supplied Accessories… 6 Block Hour 25

Controls 7,8,9 Parental Lock 25

Installation Change Password 25

Locations Guidelines 10 Glossary and Rating 26

OSHPD (State of California Only) 10 Other Functions

Cable System Grounding 10 PIP Function 27

Wall Mounting TV with the Supplied Bracket 11 Viewing the PIP Picture 27

Exploded View 12 Selecting the PIP Picture Mode 27

Across-Room Wiring 13 Moving the PIP Picture 27

Basic Operation Switching between Main and Sub Picture 27

Turning the TV On and Off 14 Closed Caption 27

Channel Selection 14 Power On Channel 28

Volume Adjustment 14 Copy Service Level 28

Quick View 14 Clear Service Level 28

Sound Mute Function 14 Service Level 29

On Screen Menu Language Selection 14 Channel Lock 29

On Screen Menus and Displays Channel Memory Override 29

Menu Navigation 15 Power On Captions Mode 29

Setting Up TV Channels Radio Control

Auto Program 16 Mode 30

Manual Program 17 Frequency 30

Program List 17 Program 30

Picture Controls Memorize 30

Picture 18 Delete 30

PSM (Picture Status Memory) 18 Radio Auto Program 31

Sound Controls Off Time 31

Equalizer 19 Radio Edit Name 31

SSM (Sound Status Memory) 19 External Equipment Connection

Balance 19 Antenna Connection 32

AVL (Automatic Volume Level) 20 Component Input 32

Sound Mode 20 DTV Input 33

Maximum Volume 20 S-Video Input 33

Minimum Volume 20 A/V Input 34

Power On Volume 20 A/V Output 34

Special Functions Computer Video In 35

Clock 21 Picture Adjust 35

Blue Back (Background) 21 ARC (Aspect Ratio Control) 36

Auto Sleep 22 Sound Adjustment 36

Lock 22 Position Adjustment 37

Radio (Enabling) 22 Auto 37

ARC (Aspect Ratio Control) 22 Reset 37

Auto Power On 23 Resolution 37

Power Management 23 Product Specification 38

Bed A/B 23 Troubleshooting 39

Limited Warranty 40

Document Number PD196-086 Rev 2

Supplied Accessor

ies

The following accessories are provided with the product.

1. AC Cord

Owner’s manual

3. Mounting Brackets & Hardware

(Not included with the “-NB”model)

4. Pillow Speaker Jumper

(Not included with the “-NB”model)

Document Number PD196-086 Rev 2

Controls

1. ON/OFF

Switches TV set on or off.

2. MENU

Displays a menu.

3. + CH -

(Program Up/Down) Selects a channel or menu item.

4. + VOL -

(Volume Up/Down)

Adjusts the volume or menu settings.

5. TV/AV

Selects TV, VIDEO, S-VIDEO, RADIO (Only when

the Radio is set to On),

PC ANALOG, PC DIGITAL or DTV mode. Clears the menu

from the screen.

Remote Control Sensor

Accepts the IR signal of remote control.

7. Power Indicator

Illuminates in red when the TV is OFF. Illuminates in green when the

TV is ON. Illuminates in amber when the power save mode is active

(only PC mode).

1. PC DIGITAL IN (DVI-D)

2. PC ANALOG IN (D-SUB)

3. AV OUT

Connect these

outputs to the Audio/Video inputs

of external equipment.

4. AV IN

Connect the

Audio/Video outputs of external

equipment to these inputs.

5. DTV IN

6. COMPONENT IN

7. S-VIDEO IN

Connect the

output of the S -VIDEO on the

VCR to the S-VIDEO input.

Connect the audio outputs of the

S-VIDEO on the VCR to the Audio

IN (L(MONO), R).

8. PC AUDIO IN

Connect the

audio cable from the PC to the

PC AUDIO IN of the set.

9. PILLOW

Pillow Speaker Port.

10. COMM

CCI/Cloner Comm

Port.

11. SPK

On Off switch for the internal TV speakers and H/P jack.

228

ON/OFF MENU CH▲CH▼VOL▲VOL▼TV/AV

1 2 3 4 5 6 7

9 10 11

Document Number PD196-086 Rev 2

Controls

All the functions can be controlled with the remote control. Some functions can

also be adjusted with the buttons on the front panel of the set. NOTE: A remote control

is NOT packed with each TV. The remote control must be ordered separately.

Remote contr

Before you use the remote control, please

install the batteries.

1. POWER

Turns the TV ON or OFF.

2. MUTE

Turns the sound on and off.

3. NUMBER buttons

Selects channel numbers.

4. TV/AV

Selects TV,

COMPONENT

, VIDEO, S-

VIDEO,

RADIO(Only with the Radio enabled),

PC ANALOG, PC DIGITAL or DTV mode.

Clears menu from the screen.

5. MENU

Displays a main menu.

6. LIST

Displays the program list menu.

7. SAP

Adjusts the MTS-STEREO, MONO, SAP.

8. SLEEP

Sets the sleep timer.

9. Q.VIEW

Returns to the previously viewed channel.

10. CH▲▼

(Channel Up/Down)

Selects next Channel or a menu item.

11. OK

Accepts your selection or displays the current

mode.

Document Number PD196-086 Rev 2

Controls

12. VOL▲▼

(Volume Up/Down)

Adjusts the sound level. Adjusts menu settings.

13. TV/PC

Selects TV or PC mode directly.

14. PSM (Picture Status Memory)

Recalls your preferred picture setting.

15. SSM (Sound Status Memory)

Recalls your preferred sound setting.

16. ARC

You can watch TV in various picture

formats;

16:9,

14:9, 4:3, 16:9 Zoom, 14:9 Zoom, 4:3

Zoom.

Repeatedly press the

ARC

button to select

your desired picture format.

Note:

In PC mode only

16:9 and 4:3 sized displays available.

17. CC

Set the closed caption function.

18. INPUT

Selects the AV source for sub picture in PIP mode.

19. PIP

Displays a PIP(Picture In Picture) screen.

The PIP function is available in PC Analog, PC Digital

or DTV mode.

20. POSITION Selects a position of PIP screen.

21. SWAP

Switches a main picture for sub picture in

PIP mode.

The PIP screen will disappear after

pressing the SWAP button.

22. MODE

Selects a PIP screen size – 16:1, 9:1 and

3:1 mode.

23. ▲

▼

Selects a channel when TV signal is

displayed in PIP window

mode.

Battery installation

Inserting batteries

1. Remove the battery cover by pulling it

upward in the direction shown by the

arrow.

2. Insert the batteries with correct polarity

( "+" to "+", and "-" to "-" ).

3. Replace the battery compartment cover.

Install two high-quality 1.5V "AAA" alkaline batteries. Don't mix old batteries

with new batteries.

Remove batteries when you won't use the remote controller for a long time. Liquid

leakage from old batteries may cause operation failure.

Notes for using remote controller

•

Make sure there are no objects between the remote controller and its sensor.

•

Don't place the remote control near a heater or in damp place. Strong impact

to the remote control may cause operation failure.

•

Signal from the remote control may be disturbed by sunlight or other bright

lights. In

this case, darken the room or move the TV.

2210

Document Number PD196-086 Rev 2

INSTALLATION

Location Guidelines

The model PDI-P23LCD Hospital Grade LCD TV is a specialized LCD

television. This TV is intended for entertainment and educational purposes for

use in a hospital, a nursing home, a medical-care center, or a similar health-

care facility in which installation is limited to a non-hazardous area in

accordance with the National Electrical Code, ANSI/NFPA 70.

The PDI-P23LCD is capable of being mounted with several commercially

available mounting brackets utilizing the 100 mm VESA hole pattern. The PDI-

P23LCD TV mounts at the foot of a patient’s bed with the supplied bracket.

Select a location that is near an AC wall outlet and that does not expose the TV

to bright room lights or sunlight if possible. The LCD TV also requires

connection of both CATV cable signal and across-room wiring for the pillow

speaker.

OSHPD (State of California Only)

The combined weight of the PDI-P23LCD TV and wall mount totals less than 20

pounds. At the time of this writing, the involvement of a written, submitted,

reviewed, and approved plan by OSHPD is not required to install the PDI-

P23LCD TV in the state of California.

Cable System Grounding

The coax cable system connected to the PDI-P23LCD TV should be grounded

in accordance with the National Electrical Code, ANSI/NFPA 70. The code

provides guidelines for proper grounding and, in particular, specifies that the

cable ground shall be connected to the grounding system of the building, as

close to the point of the cable entry as practical.

Otros manuales para PDI-P23LCD

Tabla de contenidos

Otros manuales de Televisor LCD de PDi

Manuales populares de Televisor LCD de otras marcas

LG 32LC4R* Manual de usuario

ViewSonic

ViewSonic N4200w-1 VS10945-1M Manual de usuario

Salora

Salora 22LED1600 Manual de usuario

Samsung

Samsung LA32E420 Guía

Dell

Dell W1900 19 Instrucciones de uso

Samsung

Samsung LN40C670M1F Manual de usuario

Samsung

Samsung Series 4+ Manual de usuario

Samsung

Samsung 5 Series Manual de usuario

Grundig

Grundig 40 VLE 8230 BP Manual de usuario

Philips

Philips 43PFL4901/F7 Manual de usuario

Sony

Sony Bravia XBR-43X830C Manual de usuario

LG 32LS350 Manual de usuario

VIORE

VIORE LED32VF60 Manual de usuario

Toshiba

Toshiba Regza 42HL167 Manual de usuario

JVC

JVC LT-32A220 Manual de usuario

Philips

Philips 20TA1000/93 Manual de usuario

Philips

Philips 32PFL3158T/12 Manual de usuario

Sony

Sony Bravia KDL-V32XBR2 Manual de usuario