PCW Microsystems SBC2516 Manual de usuario
Single Board Computer
SBC2516
User's Manual
1
Preface
Copyright
This document contains information protected by copyright. No part of this manual
may be reproduced, copied, translated or transmitted in any form or by any means
without the prior written consent from PCW Microsystems Inc.
Disclaimer
The information in this document is subject to change without prior notice and does
not represent commitment from PCW Microsystems Inc. However, users may
update their knowledge of any product in use by constantly checking its manual
posted on our website: www.rackmount.com
PCW shall not be liable for direct, indirect, special, incidental, or consequential
damages arising out of the use of any product, nor for any infringements upon the
rights of third parties which may result from such use. Any implied warranties of
merchantability or fitness for any particular purpose is also disclaimed.
Acknowledgements
SBC2516 is a trademark of PCW Microsystems Inc. All other product names
mentioned herein are registered trademarks of their respective owners.
Regulatory Compliance Statements
This section provides the FCC compliance statement for Class A devices and
describes how to keep the system CE compliant.
FCC Compliance Statement for Class A Devices
The product(s) described in this user’s guide has been tested and proved to com-
ply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against harmful inter-
ference when the equipment is operated in a commercial environment. This equip-
ment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the user’s guide, may cause harmful interference to
radio communications. Operation of this equipment in a residential area (domestic
environment) is likely to cause harmful interference, in which case the user will be
required to correct the interference (take adequate measures) at their own
expense.
CE Certification
The product(s) described in this user’s guide complies with all applicable
European Union (CE) directives if it has a CE marking.
2
Table of Contents
Chapter 1 General Information......................................... 4
1.1 Features..................................................................................5
1.2 Specifications ..........................................................................5
1.3 Board Layout ..........................................................................8
1.4 Checklist & Mechanical Drawing .................................................9
Chapter 2 Jumper Setting ........................................................10
2.1 Functions of Jumpers..............................................................12
2.2 Setting Jumpers.....................................................................13
2.3 Location of Jumpers ..............................................................14
2.4 Jumping Setting.....................................................................15
2.5 Connector Pin Definition .........................................................16
Chapter 3 Expanded Capabilities ............................................22
3.1 System Memory ....................................................................23
3.2 Installing DIMM .....................................................................24
3.3 Changing CPU ......................................................................26
3.4 Installing Fan Heatsink ...........................................................27
3.5 Serial ATA .............................................................................30
4
Chapter 1
General Information
5
1.1Features
oSocket 478 Intel® Pentium® 4 processor up to 3.2GHz with 800MHz FSB
oIntel® 865G/ICH5 chipsets
oMax. 2GB DDR 400/dual channel memory in 2 DIMM slots
oIntegrated VGA, CRT connector x 1
oIntel 82547EI gigabit Ethernet controller in CSA port and Intel 82551QM
10/100 Ethernet controller
oSerial ATA port (150MB/s) x 2/USB 2.0 port (480Mbps) x 2
1.2 Specifications
System Architecture
- Full size SBC with PCI/ISA golden finger.
- DVI 1.0 compliant (optional)
- PICMG 1.0 (Rev.2.0) compliant
- USB 2.0 compliant
CPU Support
- Intel® Pentium®4 processor with 256K/512K L2 cache on die
- mPGA478 socket supports 400/533/800MHz system bus; CPU speed up to
3.2GHz – Support Hyper-ThreadingTM technology
Main Memory
- DDR SDRAM DIMM x 2 support maximum 2GB (DDR 266/333/400) of
memory – Support two 64-bit DDR channels, 3.2GB/s bandwidth per channel
- Supports no Registered /non-ECC DIMMs only
BIOS - Award System BIOS
- Plug & Play support
- Advanced power management support
- ACPI 1.0b compliant
- 4M bits flash ROM
6
Chipsets
- Intel®865G (GMCH) chipsets
- Intel ICH5 for south bridge (I/O controller hub)
- Firmware hub (FWH) 4Mbits flash ROM x 1
- PCI V2.3 compliant
On Board LAN
- Intel 82547EI gigabit Ethernet controller (dedicated by CSA port directly from the Intel
865G GMCH) and Intel 82551QM 10/100 Ethernet controller x 1 for SBC2516
- Compliant with PCI V2.1/V2.2, IEEE802.3, IEEE 802.3u, IEEE802.3x, IEEE802.3y,
IEEE8023ab – WfM 2.0, PC2001 compliant
- RJ45 with LED connector x 2
On Board VGA
- Intel 865G (GMCH) chipset integrated with graphics controller
- Hardware motion compensation assist for software MPEG/DVD decode
- Access system memory
- Fully PC 98 and PC 99 compliant
- 15 pin CRT connector x 1
On Chip I/O (ICH5)
- On board USB port x 2, USB 2.0 compliant
- Ultra ATA100/66/33 support, 40 pin connector x 2. 2-pin power connector for DOM (Disk
On Module)
- Serial ATA support, SATA connector x 2 ; data transfer bandwidth up to 150MB
On Board I/O
- ITE 8712F-A Super I/O
- SIO x 2, with 2x16C550 UARTs, 10 pin header x 2
- PIO x 1, bi-directional, EPP/ECP support, 26 pin connector x 1
- Floppy disk controller: 34 pin connector x 1
- 6-pin mini DIN connector x 1 for PS/2 keyboard/mouse, and 5-pin connector x 1 for external
keyboard
- On board buzzer x 1
- GPIO (4 in 4 out )
- On board 2 –pin header for I2C
- On board 5-pin header for IrDA
- On board 2-pin header for reset SW, 4-pin for speaker, 5-pin for keylock, 2-pin for IDE active
LED, and 2-pin ATX power SW
- One 3-pin power header for 3-pin power cable connected to backplane board
to support ATX Power On function.
- On board 4-pin additional power source input
. - AC’97 output, 10 pin header x 1
7
System Monitor
-Derived from Super IO ITE 8712F-A to support system monitor
-8 voltage (For +1.5V, +3.3V, +5V, -5V, +12V, -12V, Vcore and +5VSTBY)
-Fan speed connector x 2 (one is for CPU, while the other is for system)
-Temperature sensor x 2 (one is for internal CPU, while the other is for external system)
Real Time Clock
-On-chip RTC with battery back-up
-External Li battery x 1
Watchdog Timer
-Watchdog timeout programmable by software from 1, 2, 4, 8, 16, 32... to 128 seconds
PCI to ISA Bridge & ISAMAX Support
-ITE 8888F x1 PCI to ISA Bridge –Provide 64mA driving capability to
maximize ISA signals for supporting ISA cards up to 20 on the
backplane ISA slot
Dimensions
-338.58mm(L) x 122mm(W) (13.3”(L) x 4.8”(W)
Power Requirements
-+5V, +12V, -12V, ATX/AT
Power Consumption:
Model SBC2516 (G)
CPU 3.0G 2.4G
+12V 6.5A 4.5A
+5V 5.4A 4A
+3.3V 0.5A 0.5A
+5Vsb 0.5A 0.5A
Environments
-Operating temperature: up to 60°C, below -20°C (under certain
condition) –Storage temperature: -20°C to 80°C
-Relative humidity: 10% to 90% (Non-condensing)
Certification
-CE approval
–FCC
Intel865G Chipset
w/integrated VG
A
Controller
Socket 478 Intel Pentium 4 processor
up to 3.2GHz+ with 800MHz FSB
A
TX 5V Standby
Power Connector
S
er
i
a
l
ATA
C
onnec
t
or x
2
Intel 82551QM
10/100 Ethernet
Controller
D
ua
l
LAN
I
Intel 82547EI Gigabit/CS
A
Ethernet Controller or Intel
82562EX 10/100 LCI
Ethernet Controller
Max2GB DDR 400/Dual
Channel Memory in 2
DIMM Slots
8
1.3 Board Layout
Figure 1-1: SBC2516 Front Layout
9
1.4 Checklist
After opening the package of SBC2516 Series, please check and make sure
you have all of the following items:
✍
One SBC2516 series SBC
(A mechanical drawing of this model is shown below.)
✍
One SBC2516 Manual Guide
✍
One 50CM Cable JST 2.5mm 3 pin to 3 pin (5V standby ATX Power-on
Cable)
✍
One Y Cable for Keyboard and Mouse
✍
One 180 mm AUX Power Cable (for J2)
✍
One Cable Set (FDD x1, SIO+PIO x1, SIO x1/Keyboard x1/IDE66 x1)
✍
One USB Cable with Bracket
✍
One Driver / Manual CD
Figure 1-1 : Mechanical Drawing of SBC2516 Series
Chapter 2
Jumper & Switch Settings
Tabla de contenidos
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
