PCB Piezotronics ICP 483C30 Manual de usuario

Model 483C50

ICP® Sensor Signal Conditioner

Installation and Operating Manual

For assistance with the operation of this product,

contact PCB Piezotronics, Inc.

Toll-free: 800-828-8840

24-hour SensorLine: 716-684-0001

Fax: 716-684-0987

E-mail: [email protected]

Web: www.pcb.com

The information contained in this document supersedes all similar information that

may be found elsewhere in this manual.

Total Customer Satisfaction –PCB

Piezotronics guarantees Total Customer

Satisfaction. If, at any time, for any

reason, you are not completely satisfied

with any PCB product, PCB will repair,

replace, or exchange it at no charge.

You may also choose to have your

purchase price refunded in lieu of the

repair, replacement, or exchange of the

product.

Service –Due to the sophisticated

nature of the sensors and associated

instrumentation provided by PCB

Piezotronics, user servicing or repair is

not recommended and, if attempted,

may void the factory warranty. Routine

maintenance, such as the cleaning of

electrical connectors, housings, and

mounting surfaces with solutions and

techniques that will not harm the

physical material of construction, is

acceptable. Caution should be observed

to insure that liquids are not permitted to

migrate into devices that are not

hermetically sealed. Such devices

should only be wiped with a dampened

cloth and never submerged or have

liquids poured upon them.

Repair –In the event that equipment

becomes damaged or ceases to

operate, arrangements should be made

to return the equipment to PCB

Piezotronics for repair. User servicing or

repair is not recommended and, if

attempted, may void the factory

warranty.

Calibration –Routine calibration of

sensors and associated instrumentation

is recommended as this helps build

confidence in measurement accuracy

and acquired data. Equipment

calibration cycles are typically

established by the users own quality

regimen. When in doubt about a

calibration cycle, a good “rule of thumb”

is to recalibrate on an annual basis. It is

also good practice to recalibrate after

exposure to any severe temperature

extreme, shock, load, or other

environmental influence, or prior to any

critical test.

PCB Piezotronics maintains an ISO-

9001 certified metrology laboratory and

offers calibration services, which are

accredited by A2LA to ISO/IEC 17025,

with full traceability to SI through

N.I.S.T. In addition to the normally

supplied calibration, special testing is

also available, such as: sensitivity at

elevated or cryogenic temperatures,

phase response, extended high or low

frequency response, extended range,

leak testing, hydrostatic pressure

testing, and others. For information on

standard recalibration services or

special testing, contact your local PCB

Piezotronics distributor, sales

representative, or factory customer

service representative.

Returning Equipment –Following

these procedures will insure that your

returned materials are handled in the

most expedient manner. Before

Warranty, Service, Repair, and

Return Policies and Instructions

returning any equipment to PCB

Piezotronics, contact your local

distributor, sales representative, or

factory customer service representative

to obtain a Return Warranty, Service,

Repair, and Return Policies and

Instructions Materials Authorization

(RMA) Number. This RMA number

should be clearly marked on the outside

of all package(s) and on the packing

list(s) accompanying the shipment. A

detailed account of the nature of the

problem(s) being experienced with the

equipment should also be included

inside the package(s) containing any

returned materials.

A Purchase Order, included with the

returned materials, will expedite the

turn-around of serviced equipment. It is

recommended to include authorization

on the Purchase Order for PCB to

proceed with any repairs, as long as

they do not exceed 50% of the

replacement cost of the returned

item(s). PCB will provide a price

quotation or replacement

recommendation for any item whose

repair costs would exceed 50% of

replacement cost, or any item that is not

economically feasible to repair. For

routine calibration services, the

Purchase Order should include

authorization to proceed and return at

current pricing, which can be obtained

from a factory customer service

representative.

Warranty –All equipment and repair

services provided by PCB Piezotronics,

Inc. are covered by a limited warranty

against defective material and

workmanship for a period of one year

from date of original purchase. Contact

PCB for a complete statement of our

warranty. Expendable items, such as

batteries and mounting hardware, are

not covered by warranty. Mechanical

damage to equipment due to improper

use is not covered by warranty.

Electronic circuitry failure caused by the

introduction of unregulated or improper

excitation power or electrostatic

discharge is not covered by warranty.

Contact Information –International

customers should direct all inquiries to

their local distributor or sales office. A

complete list of distributors and offices

can be found at www.pcb.com.

Customers within the United States may

contact their local sales representative

or a factory customer service

representative. A complete list of sales

representatives can be found at

www.pcb.com. Toll-free telephone

numbers for a factory customer service

representative, in the division

responsible for this product, can be

found on the title page at the front of this

manual. Our ship to address and

general contact numbers are:

PCB Piezotronics, Inc.

3425 Walden Ave.

Depew, NY14043 USA

Toll-free: (800) 828-8840

24-hour SensorLineSM: (716) 684-0001

Website: www.pcb.com

E-mail: [email protected]

PCB工业监视和测量设备 - 中国RoHS2公布表

PCB Industrial Monitoring and Measuring Equipment - China RoHS 2 Disclosure Table

部件名称

有害物质

铅(Pb)

汞

(Hg)

镉

(Cd)

六价铬(Cr(VI))

多溴联苯 (PBB)

多溴二苯醚(PBDE)

住房

PCB板

电气连接器

压电晶体

环氧

铁氟龙

电子

厚膜基板

电线

电缆

塑料

焊接

铜合金/黄铜

本表格依据 SJ/T 11364 的规定编制。

O：表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。

X：表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。

铅是欧洲RoHS指令2011/65/ EU附件三和附件四目前由于允许的豁免。

CHINA RoHS COMPLIANCE

DOCUMENT NUMBER: 21354

DOCUMENT REVISION: C

ECN: 45605

Component Name

Hazardous Substances

Lead

(Pb)

Mercury

(Hg)

Cadmium

(Cd)

Chromium VI

Compounds

(Cr(VI))

Polybrominated

Biphenyls

(PBB)

Polybrominated

Diphenyl

Ethers (PBDE)

Housing

PCB Board

Electrical

Connectors

Piezoelectric

Crystals

Epoxy

Teflon

Electronics

Thick Film

Substrate

Wires

Cables

Plastic

Solder

Copper Alloy/Brass

This table is prepared in accordance with the provisions of SJ/T 11364.

O: Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the limit

requirement of GB/T 26572.

X: Indicates that said hazardous substance contained in at least one of the homogeneous materials for this part is above

the limit requirement of GB/T 26572.

Lead is present due to allowed exemption in Annex III or Annex IV of the European RoHS Directive 2011/65/EU.

PCB PIEZOTRONICS, INC. 3425 WALDEN AVENUE DEPEW, NY 14043-2495 PHONE 716-684-0001 FAX 716-684-0987

ICP is a registered trademark of PCB Group, Inc.

Manual # 34896

Rev. A

SIGNAL CONDITIONER

Models 483C30, 483C50, 482M179 and

483M217

GENERAL OPERATION

MANUAL

For powering ICP

, and charge sensors, these signal conditioners provide an effective method for

managing large numbers of sensor channels. A simple command set, entered through industry

standard interface, allows the user to generate powerful application-specific programs to automate

system testing.

Table of Contents

Table of Contents i

Table of Figures ii

1-0.

INTRODUCTION AND SPECIFICATIONS 1

1-1.

Introduction: Safety Considerations 1

1-2.

System Description, Basic Configuration 2

1-2.1.

ICP

Input/Output Mode, All Models 2

1-3.

Block Diagram 3

1-4.

Installation 3

1-4.1.

Grounding Techniques 3

1-5.

Operation: Standard AC Line 4

1-6.

Maintenance and Repair 4

2-0.

THEORY OF OPERATION 4

2-1.

Sensor Excitation 4

2-2.

Input Protection 4

2-3.

Input Fault Detection 5

2-4.

Input Interface 5

2-5.

Gain 5

2-5.1.

Programmable Gain 6

2-6.

Normalized Output Sensitivity 6

2.7. Overload Detection and Autoscaling 6

2-7.1.

Autoscaling 7

2-7.2.

Overload 7

2-8.

Connector Configuration 7

2-9.

Non-Volatile Memory 8

2-10.

Transducer Electronic Data Sheet (TEDS) Interface: 8

2-11.

Filtering 8

2-11.1

Output Filtering 8

2-11.2

Input Filtering 9

2-11.3

Ordering Filters 9

3-0.

COMPUTER INTERFACE PROGRAMMING GUIDE 10

3-1.

Introduction 10

3-2.

Ethernet Communication 10

3-3.

Communication Guidelines 15

MODELS 483C30, 483C50 AND, 482M179 GENERAL OPERATION MANUAL

3-4.

Unit Initialization Procedure 15

3-5.

Command Summary 15

3-6.

Command Format 16

3-7.

Multiple Board Models 16

3-8.

Commands 17

GAIN 17

SENS 17

FSCI 18

FSCO 18

INPT 18

IEXC 19

OFLT 20

OSCL 20

RTED 21

ALLC 21

RBIA 22

STUS 22

UNIT 22

UNID 23

LEDS 24

RSET 24

AUTR 24

SAVS 25

WTED 25

Communication Responses 26

Table of Figures

Figure 1 Typical Block Diagram..............................................................................3

Figure 2 ICP

Sensor Excitation..............................................................................4

Figure 3 Input Fault Window Comparator with LED Indicator...............................5

Figure 4 Input Amplifier Configuration...................................................................5

MODELS 483C30, 483C50 AND, 482M179 GENERAL OPERATION MANUAL

iii

Figure 5 Selectable Gain Amplifier Configuration ...................................................5

Figure 6 Autoscale/Overload Window Comparator .................................................7

MODELS 483C30, 483C50, 482M179 AND 483M217 GENERAL OPERATION MANUAL

1-0. INTRODUCTION AND SPECIFICATIONS

1-1. Introduction: Safety Considerations

WARNING SYMBOLS AND TERMS

The following symbols and terms may be found on the equipment described in this manual.

This symbol on the unit indicates that the user should refer to the operating instructions located in the manual.

This symbol on the unit indicates that high voltage may be present. Use standard safety precautions to avoid

personal contact with this voltage.

This symbol indicates that the test fixture, Model 483C30, 483C50, 482M179 and 483M217, must be connected to

earth ground via the power cord.

The WARNING heading used in this manual explains dangers that might result in personal injury or death. Always

read the associated information very carefully before performing the indicated procedure.

The Caution heading used in this manual explains hazards that could damage the instrument.

WARNING 1: The power supply/signal conditioner should not be opened by anyone other than qualified service

personnel. This product is intended for service by qualified personnel who recognize shock hazards and are familiar

with the safety precautions required to avoid injury.

WARNING 2: This equipment is designed with user safety in mind; however, the protection provided by the equipment

may be impaired if the equipment is used in a manner not specified by PCB Piezotronics, Inc.

Caution 1: Cables can kill your equipment. High voltage ElectroStatic Discharge (ESD) can damage electrical devices.

Similar to a capacitor, a cable can hold a charge caused by triboelectric transfer, such as that which occurs in the

following:

•Laying on and moving across a rug.

•Any movement through air.

•The action of rolling out a cable.

•Contact to a non-grounded person

The solution for product safety: 1) Connect the cables only with the AC power off. 2) Temporarily “short” the end of

the cable before attaching it to any signal input or output.

Caution 2: ESD considerations should be made prior to performing any internal adjustments on the equipment. Any

piece of electronic equipment is vulnerable to ESD when opened for adjustments. Internal adjustments should therefore

be done ONLY at an ESD-safe work area. Many products have ESD protection, but the level of protection may be

exceeded by extremely high voltage that is typically present in normal situations.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de PCB Piezotronics

PCB Piezotronics

PCB Piezotronics 442A103 Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI SENSORS 641B61 Manual de usuario

PCB Piezotronics

PCB Piezotronics M221B05 Manual de usuario

PCB Piezotronics

PCB Piezotronics 356A03/NC Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI SENSORS M641B60 Manual de usuario

PCB Piezotronics

PCB Piezotronics 080A121 Manual de usuario

PCB Piezotronics

PCB Piezotronics 354C10/NC Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI Sensors M080A131 Manual de usuario

PCB Piezotronics

PCB Piezotronics ICP 137B21B Manual de usuario

PCB Piezotronics

PCB Piezotronics TORKDISC 5308D-140-02A Manual de usuario

PCB Piezotronics

PCB Piezotronics PCB LOAD & TORQUE 1102-02A Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI Sensors 080A133 Manual de usuario

PCB Piezotronics

PCB Piezotronics 351B12 Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI SENSORS VO622A11 Manual de usuario

PCB Piezotronics

PCB Piezotronics ICP 103B11 Manual de usuario

PCB Piezotronics

PCB Piezotronics PCB LOAD & TORQUE 1102-04A Manual de usuario

PCB Piezotronics

PCB Piezotronics ICP 137B22B Manual de usuario

PCB Piezotronics

PCB Piezotronics M352C68 Manual de usuario

PCB Piezotronics

PCB Piezotronics M221B02 Manual de usuario

PCB Piezotronics

PCB Piezotronics M209C12 Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI SENSORS EXM641B02 Manual de usuario

PCB Piezotronics

PCB Piezotronics JM352C66 Manual de usuario

PCB Piezotronics

PCB Piezotronics 352C17 Manual de usuario

PCB Piezotronics

PCB Piezotronics 356B20/NC Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario