Paul Agnew Ilektro Manual de usuario

U S E R I N S T R U C T I O N S AND

I N S T A L L A T I O N

IMPORTANT NOTE

THE HEATER OUTLET GRILLE BECOMES VERY HOT WHILST IN OPERATION. DO NOT COVER THE OUTLET GRILLE OR

ANY PART OF THE APPLIANCE. FOR USE WITH 110V - 120V 60HZ ELECTRICITY SUPPLY ONLY. PLEASE READ THESE

INSTRUCTIONS CAREFULLY BEFORE INSTALLATION KEEP THE INSTRUCTIONS IN A SAFE PLACE.THEY WILL BE

NEEDED WHEN MAINTENANCE OR SERVICING IS REQUIRED. THIS APPLIANCE MUST BE EARTHED.

Version 1 04/04/23

Contents of manual may be updated without notice.

For the latest version of this manual please refer to our

website: www.paulagnewdesigns.com.au

SLIMLINE RANGE

USER MANUAL

CONTENTS

THIS MANUAL COVERS THE FOLLOWING MODELS

ONLY:

IS50 IS60 & IS72

BOX CONTENTS 3

HOW TO USE YOUR APPLIANCE

HOW TO INSTALL YOUR APPLIANCE

REFERENCE INFORMATION

TERMS AND CONDITIONS WARRANTY

148 COCHRANES ROAD, MOORABBIN,

VICTORIA 3189

FULL TERMS AND CONDITIONS ARE DETAILED

IN THE WARRANTY STATEMENT ON THE

WEBSITE WWW.PAULAGNEWDESIGNS.COM.AU.

IN THE EVENT OF ANY CONFLICT OF

INFORMATION THE WORDING ON THE WEBSITE

SHALL PREVAIL. IMPORTANT NOTE: SHOULD

ANY PROBLEMS BE EXPERIENCED WITH YOUR

PRODUCT, CLAIMS MUST FIRST BE SUBMITTED

TO THE RETAILER WHERE THE APPLIANCE

WAS PURCHASED FROM WHO WILL OFFER

IMMEDIATE ASSISTANCE.

REGISTRATION NUMBER:

IN ACCORDANCE WITH EUROPEAN DIRECTIVE

2012/19/ EU, WASTE ELECTRICAL AND

ELECTRONIC EQUIPMENT (WEEE) MUST NOT

BE DISPOSED OF WITH HOUSEHOLD WASTE.

AT THE END OF ITS USEFUL LIFE PLEASE TAKE

THIS PRODUCT TO AN APPROPRIATE

RECYCLING CENTRE OR COLLECTION POINT.

YOU CAN FIND

YOUR NEAREST RECYCLING CENTRE BY USING

THE BANK LOCATOR AT

WWW.RECYCLE-MORE. CO.UK FOR UK

CUSTOMERS,

WWW.ACOR.ORG.AU FOR AUSTRALIA

CUSTOMERS

WWW.WEEEIRELAND.IE FOR CUSTOMERS

IN THE REPUBLIC OF IRELAND, OR BY

CONTACTING YOUR LOCAL AUTHORITY

1. IMPOTANT SAFETY INFORMATION

2. REMOTE CONTROL INSTRUCTIONS

3. OPERATING INSTRUCTION

4. MAINTENANCE AND CARE 10

5. TECHNICAL SPECIFICATION

6. GENERAL INSTALLATION

7. SETTING THE FUEL BED

8. ELECTRICAL CONNECTION

9. WIRING DIAGRAM

10. EXPLODED DIAGRAM

11. PRODUCT DIMENSION

BOX CONTENTS

PLEASE CHECK THAT THE FOLLOWING COMPONENTS ARE INCLUDED WITHIN THE BOX. IF

ANYTHING IS MISSING OR DAMAGED, PLEASE CONTACT THE RETAILER AND DO NOT USE

THE APPIANCE UNTIL YOU HAVE EVERYTHING.

APPLIANCE WITH POWER LEAD

REMOTE CONTROL HANDSET AND BATTERIES.

FIXING BRACKETS

INSTRUCTION MANUAL.

LOG SET.

EMBER CRYSTALS.

•

READ ALL OF THE INSTRUCTIONS

CAREFULLY BEFORE USING THE APPLIANCE.

INSTRUCTIONS ARE AVAILABLE ONLINE AT

WWW.PAULAGNEWDESIGNS.COM

•

REMOVE ALL PACKAGING AND DISPOSE OF

AT AN APPROPRIATE RECYCLING FACILITY.

•

DO NOT USE THIS APPLIANCE IN THE

IMMEDIATE SURROUNDINGS OF A BATH,

SHOWER, SWIMMING POOL OR ANY OTHER

AREA WHERE THE APPLIANCE COULD COME

INTO CONTACT WITH WATER OR HUMIDITY,

E.G. A BATHROOM.

•

DO NOT ALLOW THE APPLIANCE TO BE

COVERED OR LET THE AIR INLET/OUTLET

BECOME OBSTRUCTED AS THE APPLIANCE

MAY OVERHEAT. PLEASE NOTE THE

WARNING SYMBOL ON THE APPLIANCE.

FOR INDOOR USE ONLY. THIS APPLIANCE IS

NOT SUITABLE FOR USE OUTSIDE THE

HOUSE.

•

KEEP THE POWER CORD AWAY FROM HOT

SURFACES AND HOT CONDITIONS. DO NOT

ROUTE THE POWER LEAD IN FRONT OF THE

APPLIANCE.

•

THIS APPLIANCE MUST BE INSTALLED IN A

PURPOSE BUILT STUD-WORK ENCLOSURE

OR MOUNTED EXTERNALLY

•

ENSURE THE APPLIANCE IS LEVEL AND THAT

FURNITURE, CURTAINS ETC. ARE

POSITIONED NO CLOSER THAN 1M.

•

WHEN THE APPLIANCE HAS BEEN

INSTALLED THE POSITION OF THE PLUG

MUST BE ACCESSIBLE OR AN ISOLATION

SWITCH WILL BE INSTALLED AWAY FROM

THE APPLIANCE.

•

WHERE THE ELECTRICITY SUPPLY CABLE

HAS TO PASS THROUGH A MASONRY WALL,

STONE SURROUND ETC. ENSURE SUITABLE

RUBBER BUSHES ARE FITTED AT POSSIBLE

WEAR POINTS.

•

NEVER

LEAVE CHILDREN

UNSUPERVISED WITH AN

UNGUARDED HEATER.

•

NEVER

OBSTRUCT OR COVER THE

HEATER OUTLET.

•

NEVER INSTALL OR USE THIS

PRODUCT WHERE IT MAY COME

IN CONTACT WITH WATER I.E. A

BATHROOM OR WET ROOM.

•

NEVER

USE AEROSOLS OR STEAM

CLEANERS NEAR THIS PRODUCT.

•

NEVER

ROUTE THE ELECTRIC CABLE

NEAR THE HEATER OUTLET.

•

NEVER

ROUTE THE ELECTRIC

CABLE UNDER CARPETS OR FLOOR

COVERINGS.

•

NEVER

INSTALL THIS PRODUCT

CLOSE TO CURTAINS OR

COMBUSTIBLE MATERIALS.

•

NEVER

USE THE HEATER TO DRY

CLOTHES OR OTHER OBJECTS.

•

NEVER REMOVE THE FIREPLACE

SURROUNDING WITHOUT ISOLATING

THE ELECTRIC SUPPLY.

HOW TO USE YOUR APPLIANCE

1. IMPORTANT SAFETY

INFORMATION

IF YOU ARE INSTALLING YOUR

APPLIANCE IN TO AN EXISTING

CHIMNEY CAVITY

•

IF THE ELECTRICITY SUPPLY CABLE IS

DAMAGED DO NOT USE THE APPLIANCE

UNTIL IT HAS BEEN REPLACED. FOR SAFETY

REASONS THE REPLACEMENT HAS TO BE

CARRIED OUT BY A SERVICE AGENT OR A

SIMILARLY COMPETENT ELECTRICIAN.

•

CAUTION: IN ORDER TO AVOID A HAZARD

DUE TO INADVERTENT RESETTING OF THE

THERMAL CUT OUT, THIS APPLIANCE

MUST NOT BE SUPPLIED THROUGH AN

EXTERNAL SWITCHING DEVICE, SUCH AS A

TIMER, OR CONNECTED TO A CIRCUIT THAT

IS REGULARLY SWITCHED ON AND OFF BY

THE UTILITY

•

DO NOT OPERATE THE APPLIANCE IF IT IS

DAMAGED.

•

REPAIRS OF ELECTRICAL APPLIANCES

MUST ONLY BE PERFORMED BY AN

ELECTRICAL ENGINEER. SHOULD THE

APPLIANCE FAIL TO OPERATE, OR IN CASE

OF ANY DAMAGE, PLEASE CONTACT THE

RETAILER FROM WHOM THE APPLIANCE

WAS PURCHASED.

•

CAUTION: SOME PARTS OF THIS

PRODUCT CAN BECOME VERY HOT AND

CAUSE BURNS. PARTICULAR ATTENTION

MUST BE GIVEN WHERE CHILDREN AND

VULNERABLE PEOPLE ARE PRESENT.

•

CHILDREN AGED FROM 3 YEARS AND LESS

THAN 8 YEARS SHALL ONLY SWITCH ON/

OFF THE APPLIANCE PROVIDED THAT IT HAS

BEEN PLACED OR INSTALLED IN ITS

INTENDED NORMAL OPERATING POSITION

AND THEY HAVE BEEN GIVEN SUPERVISION

OR INSTRUCTION CONCERNING USE OF THE

APPLIANCE IN A SAFE WAY AND

UNDERSTAND THE HAZARDS INVOLVED.

CHILDREN AGED FROM 3 YEARS AND

LESS THAN 8 YEARS SHALL NOT PLUG IN,

REGULATE AND CLEAN THE APPLIANCE OR

PERFORM USER MAINTENANCE

•

ENSURE THE FLOOR AREA THE APPLIANCE

WILL SIT ON IS FLAT AND FREE FROM

LOOSE MATERIAL

•

ENSURE THE FLUE OUT FROM THE

CHIMNEY CAVITY IS SEALED

•

IN ORDER TO INSTALL YOUR APPLIANCE

EFFECTIVELY DISCUSS WITH YOUR

RETAILLER THE SURROUND NEEDED TO

ENCLOSE YOUR APPLIANCE INTO THE

INSTALLATION LOCATION

•

TO PROVIDE POWER TO THE APPLIANCE

INSTRUCT A QUALIFIED ELECTRICIAN TO

INSTALL A POWER SOCKET INSIDE THE

CHIMNEY CAVITY, ENSURING THERE IS AN

ISOLATION SWITCH ACCESSIBLE OUTSIDE

THE CAVITY

HOW TO USE YOUR APPLIANCE

1. IMPORTANT SAFETY

INFORMATION

HOW TO USE YOUR APPLIANCE

2. REMOTE CONTROL BUTTONS

AND DISPLAY

POWER

BUTTON

TEMP +/ PLUS

BUTTON

TEMP -/ MINUS

BUTTON

FLAME PICTURE

BUTTON

HEATER BUTTON

FUEL BED

BUTTON

TIMER MODE

BUTTON

TIME SETTING

BUTTON

TEMP +

BUTTON

TEMP -

BUTTON

HEATER

BUTTON

POWER

BUTTON

FLAME PICTURE

BUTTON

FIG: 05 REMOTE CONTROL BUTTONS

FIG: 06 DISPLAY CONTROL BUTTONS

�ON/OFF: TURNS APPLIANCE ON AND OFF.

�FLAME COLORS:

6 COLORS (1-2-3-4-5-6): 1. YELLOW 2. RED 3. BLUE 4. YELLOW + RED 5. YELLOW + BLUE 6. YELLOW + RED +

BLUE

�(+) (-) FLAME BRIGHTNESS:

5 SETTINGS (F5-F4-F3-F2-F1) FLAME DIMS FROM F5 TO F1. F5 IS THE BRIGHTEST SETTING.

�EMBER BED COLOR:

6 COLORS (1-2-3-4-5-6): 1. ORANGE (DEFAULT) 2. RED 3. PURPLE 4. BLUE 5. SKY BLUE 6. GREEN

�HEATER:

3 SETTINGS (H0-H1-H2): H0-NO HEATER OR BLOWER, H1-HEATER BLOWS WARM AIR 900W, H2-HEATER

BLOWS WARM AIR AT 1800W

�(+) (-) TEMPERATURE SET:

RANGE 15-30 DEGREES: CONTROL (+) TO INCREASE THE TEMPERATURE AND CONTROL (-) TO DECREASE

THE TEMPERATURE. HEATING IS ONLY TURNED ON WHEN THE SET TEMPERATURE IS ABOVE ROOM

TEMPERATURE.

�(+) (-) EMBER BED BRIGHTNESS:

5 SETTINGS (L5-L4-L3-L2-L1): EMBER BED DIMS FROM L5 TO L1. L5 IS THE BRIGHTEST SETTING.

�TIMER:

9 SETTINGS (30MIN, 1HR, 2HR, 3HR, 4HR, 5HR, 6HR, 7HR, 8HR): PRESS BUTTON UNTIL REACH DESIRED

SETTING. REFER FOLLOWING PAGE FOR WEEKLY TIMING SETTINGS.

HOW TO USE YOUR APPLIANCE

2. REMOTE CONTROL BUTTONS

AND DISPLAY

HOW TO USE YOUR APPLIANCE

2. REMOTE CONTROL BUTTONS

AND DISPLAY

SETTING THE TIME & DAY (24 HOUR CLOCK)

1. PRESS THE POWER BUTTON TO TURN THE

APPLIANCE ON.

2. PRESS AND HOLD THE TIME SETTING

BUTTON FOR 2SECS TO DISPLAY THE TIME

AND DAY AS PER FIG XX (NO NUMBERS

SHOWN AS TIME NOT SET).

3. PRESS THE TIME SETTING BUTTON AND

THE DAY YOU ARE SETTING WILL FLASH -

FIG XX

4. ADJUST THE DAY SETTING USING THE +

AND -

5. PRESS THE TIME SETTING BUTTON AND

THE HOUR YOU ARE SETTING WILL FLASH.

ADJUST THE HOUR SETTING USING THE +

AND - BUTTONS.

6. PRESS THE TIME SETTING BUTTON AND

THE MINUTE YOU ARE SETTING WILL

FLASH. ADJUST THE MINUTE SETTING

USING THE + AND - BUTTONS.

7. PRESS THE TIME SETTING BUTTON TO SET

THE TIME AND EXIT THE TIME/DAY SET-UP.

SETTING THE WEEKLY TIMER

THE TIMER ALLOWS FOR TWO ON/OFF PERIODS

(M1/M2) FOR EACH DAY OF THE WEEK AND THE

TIMER CAN BE SET USING THE FOLLOWING

PROCEDURE:

1. PRESS THE POWER BUTTON TO TURN

THE APPLIANCE ON.

2. PRESS AND HOLD THE TIMER MODE

BUTTON FOR 2SECS TO ENTER THE

TIMER SETTINGS. THE SETTINGS FOR

THE 1ST ON/OFF PERIOD (M1) FOR THE

MONDAY WILL BE SHOWN WITH THE 1ST

ON TIME AND HOUR SETTING FLASHING -

FIG xx. THE GREEN "ON" LIGHT BULB

SIGNIFIES THAT YOU ARE SETTING THE

ON TIME.

3. ADJUST THE HOUR SETTING USING THE

+AND - BUTTONS AND PRESS THE TIME

SETTING BUTTON TO SELECT THE

MINUTE SETTING. WITH THE MINUTE

SETTING FLASHING, ADJUST THE

MINUTE SETTING USING + AND -

BUTTONS.

4. PRESS THE TIME SETTING BUTTON AND

THE DISPLAY WILL MOVE TO THE 1ST

OFF TIME SETTING - FIG xx. THE RED

"OFF" LIGHT BULB SIGNIFIES THAT YOU

ARE SETTING THE OFF TIME.

5. REPEAT STEPS 2 AND 3 TO SET THE 1ST

OFF TIME.

FIG: XX

HOW TO USE YOUR APPLIANCE

2. REMOTE CONTROL BUTTONS

AND DISPLAY

SETTING THE WEEKLY TIMER (CONTINUED)

6. PRESS THE TIME SETTING BUTTON AND

THE DISPLAY WILL MOVE TO THE 2ND ON/

OFF PERIOD (M2) WITH THE 2ND ON TIME

SETTING DISPLAYED.

7. REPEAT 2 AND 5 TO SET THE 2ND ON/OFF

PERIOD - FIG xx

8. PRESS THE TIME SETTING BUTTON AND

THE DISPLAY WILL MOVE TO THE 1ST ON/

OFF PERIOD (M1) FOR TUESDAY WITH THE

1ST ON TIME SETTING DISPLAYED.

9. REPEAT STEPS 2 TO 8 FOR TUESDAY'S

SETTINGS AND REPEAT TIHIS PROCESS

FOR WEDNESDAY TO SUNDAY'S SETTINGS.

10. HAVING CONFIRMED SUNDAY'S SETTINGS,

EXIT THE TIMER SETTINGS BY NOT USING

THE REMOTE FOR 10 SECONDS AND THE

APPLIANCE WILL DEFAULT INTO NORMAL

OPERATION MODE. TO ACTIVATE THE

TIMER SETTINGS, PRESS THE TIMER MODE

BUTTON UNTIL THE TIMER SYMBOL IS

DISPLAYED ON THE SCREEN - FIGxx

THERMAL SAFETY CUT OUT

IF THE SAFETY CUT OUT FOR THE HEATER

TRIPS THE APPLIANCE HAS OVERHEATED.

IF THIS HAPPENS:

•

SWITH OFF THE DEVICE FROM THE

ISOLATION SWITCH AND ALLOW IT TO

COOL DOWN FOR A MINIMUM OF 2 HOURS

•

CHECK THE HEATER OUTLET VENTS FOR

ANY OBSTRUCTION AND CLEAR IF

NECESSARY. SEE MAINTENANCE SECTION

FOR GUIDANCE

•

PLUG IN THE APPLIANCE AND SWITCH IT ON.

THE CUT OUT WILL RESET AND THE

APPLIANCE SHOULD FUNCTION NORMALLY.

•

IF THE APPLIANCE CONTINUES TO NOT

FUNCTION CORRECTLY, CONTACT THE

RETAILER OR PLACE OF PURCHASE.

HOW TO USE YOUR APPLIANCE

3. OPERATING INSTRUCTIONS

DISPLAY INFORMATION:

TOP RIGHT CORNER OF THE APPLICANCE; ELEMENTS

OF THE DISPLAY ARE VISIBLE WHEN ILLUMINATED.

FIG: XX

THERMAL SAFETY CUT OUT

IF THE SAFETY CUT OUT FOR THE HEATER

TRIPS THE APPLIANCE HAS OVERHEATED.

IF THIS HAPPENS:

•

SWITH OFF THE DEVICE FROM THE

ISOLATION SWITCH AND ALLOW IT TO

COOL DOWN FOR A MINIMUM OF 2 HOURS

•

CHECK THE HEATER OUTLET VENTS FOR

ANY OBSTRUCTION AND CLEAR IF

NECESSARY. SEE MAINTENANCE SECTION

FOR GUIDANCE

•

PLUG IN THE APPLIANCE AND SWITCH IT ON.

THE CUT OUT WILL RESET AND THE

APPLIANCE SHOULD FUNCTION NORMALLY.

•

IF THE APPLIANCE CONTINUES TO NOT

FUNCTION CORRECTLY, CONTACT THE

RETAILER OR PLACE OF PURCHASE.

THE AIR INLET GRILLES ON THE FRONT OF

THE APPLIANCE SHOULD

UNOBSTRUCTED. FREE AIR NEEDS TO

CIRCULATE IN THIS AREA.

ALWAYS SWITCH OFF THE APPLIANCE

FROM THE ISOLATION SWITCH BEFORE

CLEANING OR

UNDERTAKING AND

MAINTENANCE.

GENERAL CLEANING

•

ONLY CLEAN THE GLASS WHEN ITS COLD

•

DO NOT USE ABRASIVE CLEANERS ON ANY

PART OF THE APPLIANCE

•

USE A LINT FREE CLOTH TO WIPE ANY

SURFACES

•

DO NOT SPRAY CLEANER INTO THE

APPLIANCE

CLEANING THE FUEL BED

TO ACCESS THE FUEL EFFECT IT WILL BE

NECESSARY TO REMOVE THE FRONT GLASS

VIEWING PANEL, SEE SERVICING SECTION

•

ENSURE THE APPLIANCE IS SWITCHED OFF

AT ISOLATION SWITCH.

•

REMOVE THE LOGS AND DUST CLEAN. DO

NOT WET THE LOGS.

•

USE A LINT FREE DUSTER.

•

LIFT ALL FUEL MEDIA OUT OF THE FIRE

AND WIPE FUEL BED DOWN.

•

ENSURE NO MOISTURE REMAINS BEFORE

RETURNING THE LOGS INTO POSITION. SEE

LOG INSTALLATION PROCESS.

•

CAUTION: REPLACE FRONT TRIM WHILE

REMOVING LOGS AND FUEL MATERIAL TO

ENSURE PIECES DO NOT FALL INTO THE

APPLIANCE

•

REPLACE THE GLASS AND TRIM AS

DESCRIBED IN THE SERVICING INSTRUCTION

SECTION.

HOW TO USE YOUR APPLIANCE

3. OPERATING INSTRUCTIONS

HOW TO USE YOUR APPLIANCE

4. MAINTENANCE AND CARE

Tabla de contenidos

Otros manuales de Chimenea de interior de Paul Agnew

Paul Agnew

Paul Agnew i700 Series Manual de usuario

Paul Agnew

Paul Agnew Ilektro 950A Manual de usuario

Paul Agnew

Paul Agnew Aerion Series Guía de instalación

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación

Paul Agnew ilektro Manual de usuario

Manuales populares de Chimenea de interior de otras marcas