Patton electronics 1090 Manual de usuario

SERVICE

MANUAL

Model 1090, Model 1092,

Model 1093, Model 1095,

Model 1185, Model 2500,

Model 2510, Model 2520 &

Model 2703

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

http://www.patton.com

Part# 07M1090SVC-C

Doc# 032010U,

Rev. D

Revised 1/22/08

An ISO-9001

Certified Company

Dear Valued Customer,

Thank you for purchasing Patton Electronics products! We do

appreciate your business. I trust that you find this user manual helpful.

We manufacture one of the widest selections of data communications

products in the world including CSU/DSU's, network termination units,

powered and self-powered short range modems, fiber optic modems, interface

converters, baluns, electronic data switches, data-line surge protectors,

multiplexers, transceivers, hubs, print servers and much more. We produce

these products at our Gaithersburg, MD, USA, facility, and can custom

manufacture products for your unique needs.

We would like to hear from you. Please contact us in any of the

following ways to tell us how you like this product and how we can meet your

product needs today and in the future.

Web: http:www.patton.com

Sales E-mail: [email protected]

Support E-mail: [email protected]

Phone - Sales (301) 975-1000

Phone - Support (301) 975-1007

Fax: (301) 869-9293

Mail: Patton Electonics Company

7622 Rickenbacker Drive

Gaithersburg, MD 20879 USA

We are committed to a quality product at a quality price. Patton

Electronics is ISO 9001 certified. We meet and exceed the highest standards in

the industry (CE, UL, etc.).

It is our business to serve you. If you are not satisfied with any

aspect of this product or the service provided from Patton Electronics or its

distributors, please let us know.

Thank you.

Burton A.Patton

Executive Vice President

P.S. Please tell us where you purchased this product.

_________________________________________________________

_______________________________________________________________

1.0 SCOPE

This manual covers Fuse Replacement and Power Line Voltage

Settings for Patton Models 1090, 1092, 1093, 1095, 1185, 2500, 2510,

2520 and 2703.

1.1 DEFINITION OF SERVICE PERSONNEL

Service Personnel are defined as persons who have the

appropriate technical training and experience necessary to (A) perform

tasks in the SERVICE ACCESS AREA of the equipment, and (B) be

aware of hazards to which they are exposed in performing a task, and

of measures to minimize the danger to themselves or other persons.

WARNING! Only Service Personnel are to access the

area inside the plastic shield marked with the electric

shock symbol. (See 1.1 below.)

2.0 SERVICE PROCEDURES

This section describes the procedures for Power Line Voltage

Settings and Fuse Replacement for Patton Models 1090, 1092, 1093,

1095, 1185, 2500, 2510, 2520 and 2703. Note: These procedures

apply generally to all products listed above, which (products) will

henceforth be referred to as “the unit”.

2.1 PROCEDURE FOR POWER LINE VOLTAGE SETTING

A. Switch the unit OFF.

B. Remove the power plug from the AC wall outlet.

C. Remove the power plug out of the rear of the unit.

D. Switch the unit ON and verify that none of the front panel status

indicators are lit. Switch the unit OFF.

E. Remove the metal screws located on the rear panel bottom left

and bottom right. DO NOT DISCARD THE SCREWS. Gently

slide the PC board and the rear panel out from the metal

enclosure.

F. Remove the nylon screws that hold the clear plastic shield

in place. Lift off the plastic shield. DO NOT DISCARD THE

SCREWS OR THE PLASTIC SHIELD.

G. With a flat blade screw driver, gently select the voltage to the

desired setting.

H. Look at the fuse rating shown on the label near the fuse holder.

The required rating is different for the new voltage setting you have

just selected, change the fuse. (See Section 2.2, Step G.)

I. Reinstall the plastic shield so that all of the holes line up with

the stand-offs. Reinstall the nylon screws. DO NOT

OVERTIGHTEN THE NYLON SCREWS!

J. Line up the PC board with the 2 slots located on the rear panel

bottom left and right. Gently slide the PC board/Rear panel

WARNING! When you change the voltage setting, you

may have to remove the fuse and replace it with a fuse of a

different value. (The proper fuse rating is marked on the

board near the fuse holder.) Operating this equipment

with the wrong fuse rating may result in a fire.

1.0 SCOPE

This manual covers Fuse Replacement and Power Line Voltage

Settings for Patton Models 1090, 1092, 1093, 1095, 1185, 2500, 2510,

2520 and 2703.

1.1 DEFINITION OF SERVICE PERSONNEL

Service Personnel are defined as persons who have the

appropriate technical training and experience necessary to (A) perform

tasks in the SERVICE ACCESS AREA of the equipment, and (B) be

aware of hazards to which they are exposed in performing a task, and

of measures to minimize the danger to themselves or other persons.

WARNING! Only Service Personnel are to access the

area inside the plastic shield marked with the electric

shock symbol. (See 1.1 below.)

2.0 SERVICE PROCEDURES

This section describes the procedures for Power Line Voltage

Settings and Fuse Replacement for Patton Models 1090, 1092, 1093,

1095, 1185, 2500, 2510, 2520 and 2703. Note: These procedures

apply generally to all products listed above, which (products) will

henceforth be referred to as “the unit”.

2.1 PROCEDURE FOR POWER LINE VOLTAGE SETTING

A. Switch the unit OFF.

B. Remove the power plug from the AC wall outlet.

C. Remove the power plug out of the rear of the unit.

D. Switch the unit ON and verify that none of the front panel status

indicators are lit. Switch the unit OFF.

E. Remove the metal screws located on the rear panel bottom left

and bottom right. DO NOT DISCARD THE SCREWS. Gently

slide the PC board and the rear panel out from the metal

enclosure.

F. Remove the nylon screws that hold the clear plastic shield

in place. Lift off the plastic shield. DO NOT DISCARD THE

SCREWS OR THE PLASTIC SHIELD.

G. With a flat blade screw driver, gently select the voltage to the

desired setting.

H. Look at the fuse rating shown on the label near the fuse holder.

The required rating is different for the new voltage setting you have

just selected, change the fuse. (See Section 2.2, Step G.)

I. Reinstall the plastic shield so that all of the holes line up with

the stand-offs. Reinstall the nylon screws. DO NOT

OVERTIGHTEN THE NYLON SCREWS!

J. Line up the PC board with the 2 slots located on the rear panel

bottom left and right. Gently slide the PC board/Rear panel

WARNING! When you change the voltage setting, you

may have to remove the fuse and replace it with a fuse of a

different value. (The proper fuse rating is marked on the

board near the fuse holder.) Operating this equipment

with the wrong fuse rating may result in a fire.

assembly back into the enclosure. Proper installation has been

achieved when the all of the indicators and switches are aligned at

the front panel and the rear panel bezel is fully mated into the

enclosure. DO NOT FORCE THE UNIT INTO THE ENCLOSURE.

THIS USUALLY INDICATES THAT THE PC BOARD WAS NOT

INSERTED INTO THE 2 SLOTS PROPERLY.

K. Reinstall the two metal screws that were removed as instructed in

Step E, above.

L. Inspect the label on the bottom of the unit. A new label must be

added to indicate that the unit is now configured for the new

operating voltage.

M. BEFORE CONNECTING THE POWER CORD, VERIFY THAT

THE LINE VOLTAGE IS WITHIN THE VOLTAGE RANGE

SPECIFIED FOR THE UNIT. THIS RATING IS STATED ON THE

LABEL ON THE BOTTOM OF THE UNIT. AN IMPROPER LINE

VOLTAGE CONNECTION MAY RESULT IN DAMAGE,

IMPROPER FUNCTIONING, OR BOTH. INSTALL THE CIRCUIT

POWER CORD ACCORDING TO THE OPERATORS'

MANUAL INSTRUCTIONS.

2.2 PROCEDURE FOR FUSE REPLACEMENT

Steps A to F and J to N in the instructions below apply to all

models. Step G is different for the Model 2703 than for the other

models.

(Steps A TO F are for all units)

A. Switch the unit OFF.

B. Remove the power plug from the AC wall outlet.

C. Remove the power plug out of the rear of the unit.

D. Switch the unit ON and verify that none of the front panel status

indicators are lit. Switch the unit OFF.

E. Remove the metal screws located on the rear panel bottom left

and bottom right. DO NOT DISCARD THE SCREWS. Gently

slide the PC board and rear panel out from the metal enclosure.

F. Remove the nylon screws that hold the clear plastic shield in

place. Lift off the plastic shield. DO NOT DISCARD THE SCREWS

OR THE PLASTIC SHIELD.

(Step G is for Models 1090, 1092, 1093, 1095, 1185, 2500, 2510 and

2520.)

G.) With a flat blade screw driver, gently pry off the fuse cover. DO

NOT DISCARD THIS COVER! Pull out the fuse. Replace the fuse

and reinstall the fuse cover.

(Steps H and I are for Model 2703.)

H.) With a flat blade screw driver, gently turn the movable section of

the fuse cartridge holder counterclockwise. The spring action

should push out the fuse.

I.) After inserting the correct fuse in the fuse cartridge holder, re-

insert the movable section of the fuse cartridge holder with the new

fuse into the fixed section of the fuse holder. Gently push and

rotate clockwise while pushing until some resistance is felt and the

cover is aligned with the fuse holder.

(Steps J to O apply to all units.)

J.) BEFORE CONNECTING THE POWER CORD, VERIFY THAT

THE LINE VOLTAGE IS WITHIN THE VOLTAGE RANGE

SPECIFIED FOR THE UNIT. THIS RATING IS STATED ON THE

LABEL ON THE BOTTOM OF THE UNIT. AN IMPROPER LINE

VOLTAGE CONNECTION MAY RESULT IN DAMAGE,

IMPROPER FUNCTIONING, OR BOTH. INSTALL THE CIRCUIT

POWER CORD ACCORDING TO THE OPERATORS'

MANUAL INSTRUCTIONS.

K.) Reinstall the plastic shield so that all of the holes line up with

the stand-offs. Reinstall the nylon screws. DO NOT

OVERTIGHTEN THE NYLON SCREWS!

WARNING! Replace the fuse only with one that has

the correct voltage and current rating for the voltage

setting of the unit (the proper fuse ratings is marked on

the board near the fuse holder). Replacing the fuse with

one having an incorrect rating can result in a fire!

WARNING! Replace the fuse only with one that has

the correct voltage and current rating for the voltage

setting of the unit (the proper fuse rating is marked on

the board near the fuse holder). Replacing the fuse with

one having an incorrect rating can result in a fire!

assembly back into the enclosure. Proper installation has been

achieved when the all of the indicators and switches are aligned at

the front panel and the rear panel bezel is fully mated into the

enclosure. DO NOT FORCE THE UNIT INTO THE ENCLOSURE.

THIS USUALLY INDICATES THAT THE PC BOARD WAS NOT

INSERTED INTO THE 2 SLOTS PROPERLY.

K. Reinstall the two metal screws that were removed as instructed in

Step E, above.

L. Inspect the label on the bottom of the unit. A new label must be

added to indicate that the unit is now configured for the new

operating voltage.

M. BEFORE CONNECTING THE POWER CORD, VERIFY THAT

THE LINE VOLTAGE IS WITHIN THE VOLTAGE RANGE

SPECIFIED FOR THE UNIT. THIS RATING IS STATED ON THE

LABEL ON THE BOTTOM OF THE UNIT. AN IMPROPER LINE

VOLTAGE CONNECTION MAY RESULT IN DAMAGE,

IMPROPER FUNCTIONING, OR BOTH. INSTALL THE CIRCUIT

POWER CORD ACCORDING TO THE OPERATORS'

MANUAL INSTRUCTIONS.

2.2 PROCEDURE FOR FUSE REPLACEMENT

Steps A to F and J to N in the instructions below apply to all

models. Step G is different for the Model 2703 than for the other

models.

(Steps A TO F are for all units)

A. Switch the unit OFF.

B. Remove the power plug from the AC wall outlet.

C. Remove the power plug out of the rear of the unit.

D. Switch the unit ON and verify that none of the front panel status

indicators are lit. Switch the unit OFF.

E. Remove the metal screws located on the rear panel bottom left

and bottom right. DO NOT DISCARD THE SCREWS. Gently

slide the PC board and rear panel out from the metal enclosure.

F. Remove the nylon screws that hold the clear plastic shield in

place. Lift off the plastic shield. DO NOT DISCARD THE SCREWS

OR THE PLASTIC SHIELD.

(Step G is for Models 1090, 1092, 1093, 1095, 1185, 2500, 2510 and

2520.)

G.) With a flat blade screw driver, gently pry off the fuse cover. DO

NOT DISCARD THIS COVER! Pull out the fuse. Replace the fuse

and reinstall the fuse cover.

(Steps H and I are for Model 2703.)

H.) With a flat blade screw driver, gently turn the movable section of

the fuse cartridge holder counterclockwise. The spring action

should push out the fuse.

I.) After inserting the correct fuse in the fuse cartridge holder, re-

insert the movable section of the fuse cartridge holder with the new

fuse into the fixed section of the fuse holder. Gently push and

rotate clockwise while pushing until some resistance is felt and the

cover is aligned with the fuse holder.

(Steps J to O apply to all units.)

J.) BEFORE CONNECTING THE POWER CORD, VERIFY THAT

THE LINE VOLTAGE IS WITHIN THE VOLTAGE RANGE

SPECIFIED FOR THE UNIT. THIS RATING IS STATED ON THE

LABEL ON THE BOTTOM OF THE UNIT. AN IMPROPER LINE

VOLTAGE CONNECTION MAY RESULT IN DAMAGE,

IMPROPER FUNCTIONING, OR BOTH. INSTALL THE CIRCUIT

POWER CORD ACCORDING TO THE OPERATORS'

MANUAL INSTRUCTIONS.

K.) Reinstall the plastic shield so that all of the holes line up with

the stand-offs. Reinstall the nylon screws. DO NOT

OVERTIGHTEN THE NYLON SCREWS!

WARNING! Replace the fuse only with one that has

the correct voltage and current rating for the voltage

setting of the unit (the proper fuse ratings is marked on

the board near the fuse holder). Replacing the fuse with

one having an incorrect rating can result in a fire!

WARNING! Replace the fuse only with one that has

the correct voltage and current rating for the voltage

setting of the unit (the proper fuse rating is marked on

the board near the fuse holder). Replacing the fuse with

one having an incorrect rating can result in a fire!

L.) Line up the PC board with the two slots located on the rear panel

bottom left and bottom right. Gently slide the PC board/rear panel

assembly back into the enclosure. It is properly installed when the

all of the indicators and switches are aligned at the front panel and

the rear panel bezel is fully mated into the enclosure. DO NOT

FORCE THE UNIT INTO THE ENCLOSURE. THIS USUALLY

INDICATES THAT THE PC BOARD WAS NOT INSERTED INTO

THE TWO SLOTS PROPERLY.

M.) Reinstall the two metal screws that were removed as instructed in

Step E, above.

N.) Reinstall the power cord according to the Operator's Manual

instructions.

3.0 REPLACEMENT FUSES

The following replacement fuses are available directly from Patton

Electronics. You may also use the reference part numbers to order

directly from the manufacturer.

Patton Part Number Part Description

Patton Models 1090, 1092, 1093, 1185, 2500, 2510, 2520, 2703

and 2703-X21 (120/230V switch-selectable

units)

08242........................ Fuse 5x20mm, 100mA, 250V, Time-lag

Littelfuse P/N 218.100

Patton Models 1090-DC, 1090-UI, 1092-DC, 1093-DC, 1095-DC,

1095-UI, 1185-DC, 2703-DC, 2703-UI,

2703-UI, 2703-X21-DC and 2703-X21-UI:

0821R2....................... Fuse 5x20mm, 200mA, 250V, Time-lag

Littlelfuse P/N 239.200

L.) Line up the PC board with the two slots located on the rear panel

bottom left and bottom right. Gently slide the PC board/rear panel

assembly back into the enclosure. It is properly installed when the

all of the indicators and switches are aligned at the front panel and

the rear panel bezel is fully mated into the enclosure. DO NOT

FORCE THE UNIT INTO THE ENCLOSURE. THIS USUALLY

INDICATES THAT THE PC BOARD WAS NOT INSERTED INTO

THE TWO SLOTS PROPERLY.

M.) Reinstall the two metal screws that were removed as instructed in

Step E, above.

N.) Reinstall the power cord according to the Operator's Manual

instructions.

3.0 REPLACEMENT FUSES

The following replacement fuses are available directly from Patton

Electronics. You may also use the reference part numbers to order

directly from the manufacturer.

Patton Part Number Part Description

Patton Models 1090, 1092, 1093, 1185, 2500, 2510, 2520, 2703

and 2703-X21 (120/230V switch-selectable

units)

08242........................ Fuse 5x20mm, 100mA, 250V, Time-lag

Littelfuse P/N 218.100

Patton Models 1090-DC, 1090-UI, 1092-DC, 1093-DC, 1095-DC,

1095-UI, 1185-DC, 2703-DC, 2703-UI,

2703-UI, 2703-X21-DC and 2703-X21-UI:

0821R2....................... Fuse 5x20mm, 200mA, 250V, Time-lag

Littlelfuse P/N 239.200

USER

MANUAL

MODEL 503S

Serial Surge Protector

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

http://www.patton.com

Part# 07M503S-D

Doc# 074201UD,

Rev. E

Revised 1/21/08

CERTIFIED

An ISO-9001

Certified Company

Dear Valued Customer,

Thank you for purchasing Patton Electronics products! We do

appreciate your business. I trust that you find this user manual helpful.

We manufacture one of the widest selections of data communications

products in the world including CSU/DSU's, network termination units,

powered and self-powered short range modems, fiber optic modems, interface

converters, baluns, electronic data switches, data-line surge protectors,

multiplexers, transceivers, hubs, print servers and much more. We produce

these products at our Gaithersburg, MD, USA, facility, and can custom

manufacture products for your unique needs.

We would like to hear from you. Please contact us in any of the

following ways to tell us how you like this product and how we can meet your

product needs today and in the future.

Web: http://www.patton.com

Sales E-mail: [email protected]

Support E-mail: [email protected]

Phone - Sales (301) 975-1000

Phone - Support (301) 975-1007

Fax: (301) 869-9293

Mail: Patton Electronics Company

7622 Rickenbacker Drive

Gaithersburg, MD 20879 USA

We are committed to a quality product at a quality price. Patton

Electronics is ISO 9001 certified. We meet and exceed the highest standards

in the industry (CE, UL, etc.).

It is our business to serve you. If you are not satisfied with any

aspect of this product or the service provided from Patton Electronics or its

distributors, please let us know.

Thank you.

Burton A.Patton

Vice President

P.S. Please tell us where you purchased this product:

_________________________________________________________

Otros manuales para 1090

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de Patton electronics

Patton electronics

Patton electronics RocketLink-G 3088/I Manual de usuario

Patton electronics

Patton electronics ACC-S02 Manual de usuario

Patton electronics

Patton electronics RocketLink-G 3008/I Manual de usuario

Patton electronics

Patton electronics Model 2604 Manual de usuario

Patton electronics

Patton electronics 2710RC Series Manual de usuario

Patton electronics

Patton electronics ForeFront 2616RC Manual de usuario

Patton electronics

Patton electronics 3095 Manual de usuario

Patton electronics

Patton electronics 450RC24 Manual de usuario

Patton electronics

Patton electronics NetLink 2707C Manual de usuario

Patton electronics

Patton electronics 2500RC Manual de usuario

Patton electronics

Patton electronics NetLink 2701/B Manual de usuario

Patton electronics

Patton electronics OnSite 9100 Manual de usuario

Patton electronics

Patton electronics 2715 Manual de usuario

Patton electronics

Patton electronics NetLink 2960 RAS Manual de usuario

Patton electronics

Patton electronics ForeFront 6081RC EdgeRoute Manual de usuario

Patton electronics

Patton electronics 3101RC Manual de usuario

Patton electronics

Patton electronics OnSite 2884 Manual de usuario

Patton electronics

Patton electronics 3324 Manual de usuario

Patton electronics

Patton electronics 2784 NAU Manual de usuario

Patton electronics

Patton electronics ForeFront 2616RC Manual de usuario

Patton electronics

Patton electronics SmartNode 4654 Series Manual de usuario

Patton electronics

Patton electronics Model 2604 Manual de usuario

Patton electronics

Patton electronics NetLink 2707C Manual de usuario

Patton electronics

Patton electronics 2715RC Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario