Patpet P-collar 310 Guía de configuración

For 1 Dog

p-collar 310

For 2 Dogs

p-collar 310B

PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING

Remote Training Collar

operating and training guide

B-310-TEX-111(3)

Important Safety Information

important that you and your dog remain

safe while learning during on-leash training.

Your dog should be on a strong leash, long enough for him to

attempt to chase an object, but short enough for him not to reach

a road or other unsafe area. You must also be physically strong

Safety during on-leash training. It is vitally

enough to restrain your dog when he tries to chase.

long or made too tight on the pet’s neck may cause skin damage.

commonly known as bed sores.

Risk of skin damage. Please read and follow

the instructions in this manual. Proper ﬁt of

the collar is important. A collar worn for too

Ranging from redness to pressure ulcers; this condition is

behavior. Aggressive dogs can cause severe injury and even

use this Product if your dog is aggressive,

or if your dog is prone to aggressive

Not for use with aggressive dogs. Do not

death to their owner and others. If you are unsure whether this

product is appropriate for your dog, please consult your

veterinarian or certiﬁed trainer.

Avoid leaving the collar on the dog for more than 12 hours per day.

When possible reposition the collar on the pet’s neck every

Check the ﬁt to prevent excessive pressure; follow the

Never connect a lead to the electronic collar; it will cause

excessive pressure on the contacts.

When using a separate collar for a lead, don’t put pressure

1 to 2 hours.

instructions in this manual.

on the electronic collar.

If redness or sores are found, discontinue use until the skin

Millions of pets are comfortable while they wear stainless steel

contacts. Some pets are sensitive to contact pressure. You

collar. If so, you may relax some of these precautions. It is

may ﬁnd after some time that your pet is very tolerant of the

These steps will help keep your pet safe and comfortable.

important to continue daily checks of the contact area.

has fully healed.

Table of Contents

Components...............................................................

Other Items You May Need........................................

Main Features............................................................

Overview....................................................................

Operating Guide.........................................................

How to turn the p-collar 310 on/off..........................

How the transmitter buttons work...........................

Collar fitting.............................................................

How to set the best Vibration/Shock Level.............

To maximize the distance.......................................

The LCD & LED indicator.......................................

Charging the unit....................................................

How to pair the Transmitter and Receiver Collar....

How to use the Test Light............................... ........

Gerneral Training Tips...............................................

Frequently Asked Questions.....................................

Troubleshooting......................................................

Warranty and Repair Informatiion.............................

Reference Size for Difference Dogs..........................

Reference Weight for Dogs.......................................

Wash the dog’s neck area and the contacts of the collar

weekly with a damp cloth.

If the condition persists beyond 48 hours, see your veterinarian.

If a rash or sore is found, discontinue use of the collar until

the skin has healed.

Dog 1/2 Button Function......................................... 11

Main Features

Shock, Vibration, and Tone Commands

100% Waterproof Receiver Collar

2-hour Rapid Charging Lithium Polymer Battery

300M Remote Training Range

User Expandable to a Two-dog System

Blind Operation with Touch Distinguishing Mode Buttons

8 Adjustable Intensity Levels for Vibration and

16 Adjustable Intensity Levels for Shock

For 1 Dog

For 2 Dogs

Backlit LCD Display Shows Intensity Level, Battery

and Dog 1/2.

ŸScrewdriver

ŸScissors

ŸLighter

Test Light

Dog 1 Receiver Collar

Battery Charger

Wrist Strap

Dog 2 Receiver Collar

Collar

for Transmitter

for Receiver

USB Port

conductive

Silicone Jacket

Contact Points

Remote

Transmitter

Components

Other Items You May Need

Collar

Overview

LED Indicator Light

White Backlit

LCD Display

Blind Operation

Identification Point

Easily distinguish

and send the correct

training command

without eyes on by

touching and feeling

on buttons with

different structure.

Selecting Channels

Intensity Level

Adjustment

Antenna

Wrist Strap Pin

Transmitter

Contact

Points

Charging Jack

(with cover)

Receiver Collar

On/Off

Button

Operating Guide

Step

How to turn the p-collar 310 on/off

To turn the Transmitter on

To turn the Receiver Collar off

2. Release the On/Off Button.

light shuts off.(This takes approximately three seconds.)

1. Press and hold the On/Off Button until the Red LED

Note: To extend the life of the batteries, turn the

Receiver Collar off when it is not in use.

2. Backlight will stay for about 30 seconds. if no operation

then, backlight off.

3. LCD display will stay for about 5 minutes. if no operation

then, LCD display shuts off.

1. Press any of to active the Transmitter.

The backlight on.

To turn the Receiver Collar on

Press once, the green light on and will flash every

5 seconds under working mode.

Action Buttons

Avoid the injuryto the

dog’s skin becauseof

the friction of metal

contact points.

Conductive Silicone Jacket

To turn the Transmitter oﬀ

Transmitter DO NOT have turn oﬀ function. In order

to give a rapid reation by pressingTransmitter in

time when dogs have a badbehavior. In this case,

if need to turn on the transmitter, we may miss the

best training time.

Step

How the Transmitter buttons work

TONE

SHOCK

Up/Down

Button

VIBRA

Dog 1/2 Button

10 11

2. Press and hold , Receiver Collar will have a

continuous vibration/shock, and stop after 10 seconds.

Note: Do not suggest to press and hold for long

time to avoid physical or psychological hurt to the dog.

1. Press once to send a vibration, sound,

shock command to Receiver Collar.

1. Press once to switch between Dog 1 and Dog 2.

2. Press and hold until the Vibration digit flashes.

Press “ + - “ to adjust Vibration Level from 1-8.

1/2

3. Press and hold until the Shock digit flashes.

Press “ + - “ to adjust Shock Level from 1-16.

1/2

Step

How to find the best

Vibration/Shock Level

The unit comes with Up and Down buttons to control

the Vibration/Shock Level, with Level 1 being the

The level of Vibration/Shock best suited for your dog

for Vibration/Shock. Always start at the lowest level

and work your way up.

The appropriate level can be found when the dog

/Shock Level may vary depending on the training

situation. When highly distracted, dogs will require a

lowest level for Both Vibration and Shock, Level 8

depends on your dog’s temperament and threshold

higher level of Vibration/Shock.

being the highest for Vibration and Level 16 being

responds to the Vibration/Shock with a mild reaction,

such as a tensing of the neck muscles. The Vibration

the highest for Shock.

Collar fitting

you dog’s skin. When properly fitted, the Receiver/Collar

should not move on the dog. The best location for

A loose fit can allow the Receiver/Collar to move

The Receiver/Collar should be fitted so that the surgical

around on the dog’s neck. When this happens, the

contact points may rub the skin and cause irritation.

If the Receiver/Collar is too tight, the dogs may have

difficulty breathing.

dog’s skin. When properly fitted, you should be able

the Receiver/Collar box is either side of the dog’s

windpipe.

stainless steel contact points press firmly against the

to fit a finger or two snugly in between the collar and

Step

12 13

Step

1/2

1. Press and hold until the Vibration digit flashes.

Press “ + - “ to adjust Vibration Level from 1-8.

2. Press and hold until the Shock digit flashes.

Press “ + - “ to adjust Shock Level from 1-16.

How to switch Between

Vibra Level and Shock Level

Transmitter LED Indicator Light – Function and Response

Button Button Function Transmitter Indicator

Light Response

Delivers audible tone to collar Red LED on for

length of button press

Delivers vibration to collar

base on current level shown

on Digital Display (vibration

will time-out if pressed

continuously for 10 seconds

and will reset after release

the VIBRA button)

Red LED on for

length of button press

Delivers shock to collar base

on current level shown on

Digital Display (shock will

time-out if pressed

continuously for 10 seconds

and will reset after release

the SHOCK button)

Red LED on for

length of button

press

*Avoid touching the antenna or the range may

decrease substantially.

The unit has a 300 meter range. The range may vary

the Transmitter away from your body to receive the

depending on the way the Transmitter is held. Hold

greatest range. For maximum signal strength, keep

the device properly charged.

Maximum range Typical range Minimum range

14 15

To maximize the distance

Step Step

The LCD & LED indicator

Indicates Vibration levels ranging from 1-8,

and appears in the right upper part.

Indicates the active dog receiver and

appear in the left part.

Indicates battery’s power level.

Note: The battery indicator will flash every

second to indicate low battery.

Indicates Shock levels ranging from 1-16,

and appears in the right lower part.

3. Connect the charger connectors to the Transmitter and

1. Plug the charger into a standard wall outlet.

2. Lift the rubber covers protecting the Transmitter/Receiver

Collar Charging Jack.

4. Connect the USB port to the Charging Adapter.

5. Charge the unit for 4 hours for the first charge. Recharges

Receiver Collar Charging Jack, and as shown below.

take only 2-3 hours.

Note: The Battery Indicator on the Transmitter will scroll and

the indicator light in steady red while charging; and the Battery

flashes when fully charged.

The indicator light on the Receiver Collar will be in steady red

Indicator will become steady, and the LED Indicator Light

while charging and green light turned on when fully charged.

6. When charging is completed, remove the charger connector.

Charging the unit

The unit uses Lithium-Polymer batteries.

1. Charge the unit before using the unit for the first time.

2. Do not charge the unit near any flammable

substances.

3. Fully charge if the unit is to be stored without use for

a period of 3 months or more.

Receiver Collar Function

Normal operation

- Low battery

Red LED Response

On for 3 seconds

Flashes rapidlly

On length of VIBRA/SHOCK

button press

On length of charging within

2-3 hours

Power off

Vibration/Shock

Charging

Step

Recharge the unit if:

The indicator light on the collar is emitting a red color

and flashes rapidly.

The 3 bar indicator on the Transmitter LCD shows just

1 bar.

Battery Charging Procedure

NOTE: The unit has a partial charge when it leaves our facility,

upon receipt of the collar, be sure to give it a 4-hour initial charge

before the first use.

The indicator light on the Transmitter or Receiver will not come on.

The indicator light on the Transmitter or Receiver comes on

momentarily when any of the Mode Buttons is pushed.

16 17

Normal operation

- Good battery

Charging Complete

Receiver Collar Function Green LED Response

Flashes once

1 flash every 5 seconds

On length of TONE button press

Flashes once every second

within 15 seconds

Flashes rapidly for five times

On length of the charger connected

Power on

Training tone

In pairing position

Pairing Complete

Receiver Indicator Light – Function and Response

How to use the Test Light

Transmitter.

Save the Test Light for future testing.

Note: If the Test Light does not flash, recharge

Note: At higher Shock Levels, the Test Light

1. Turn the Receiver Collar on.

Points.

4. The Test Light will flash.

will flash brighter.

2. Hold the Test Light Contacts to the Contact

3. Press the SHOCK Button on the Remote

5. Turn the Receiver Collar off.

the Receiver and re-test. If Test Light still does

not flash, contact us for Customer Service.

Step

18 19

Step

How to pair the Remote

Transmitter & Receiver Collar

If your Receiver Collar does not beep when the TONE

Button of the Remote Transmitter is pushed,or if you

feel the Receiver Collar is not responding to the Remote

Transmitter, follow these steps to pair:

Two Dog System

NOTE: If you wish to add another Receiver Collar to

Dog 1/2 Button.

2. Turn on the Receiver Collar for Dog 2, press any

the training system, extra Receiver Collars are available

where you bought your unit.

Remote Transmitter

1. Switch Dog1 to Dog2 by pressing and releasing the

may be needed.Repeat steps in How to pair the Remote

Transmitter & Receiver Collar above.

Mode Buttons to verify function.

3. If Dog 2 Receiver Collar does not respond. Pairing

2. Press any of on the transmitter,

the Green LED Light on the Receiver Collar flashes

rapidly for 5 times which means pairing is completed.

1. With the Receiver Collar off your pet, turn the

Receiver Collar off. Restart, press and hold the On/Off

Button until the Green LED flashes every second on

the Receiver Collar.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Producto para el cuidado de mascotas de Patpet

Patpet

Patpet P-COLLAR 920 Manual de usuario

Patpet

Patpet N50 Manual de usuario

Patpet

Patpet p-collar 651 Manual de usuario

Patpet

Patpet p-collar 320 Guía de configuración

Patpet

Patpet P-COLLAR 920 Manual de usuario

Patpet

Patpet B801 Manual de usuario

Patpet

Patpet p-collar 301 Manual de usuario

Patpet

Patpet T600 Manual de usuario

Patpet

Patpet B470 Manual de usuario

Patpet

Patpet p-collar 650 Manual de usuario

Patpet

Patpet p-collar 640 Manual de usuario

Patpet

Patpet B600 Manual de usuario

Patpet

Patpet p-collar 360 Manual de usuario

Patpet

Patpet PTS-008 Manual de usuario

Patpet

Patpet 620 Series Manual de usuario

Patpet

Patpet p-collar 680 Manual de usuario

Patpet

Patpet p-collar 356 Manual de usuario

Patpet

Patpet A12 Manual de usuario

Patpet

Patpet p-collar 350 Manual de usuario

Patpet

Patpet PTS-008 Guía de configuración

Patpet

Patpet KD-661C Manual de usuario

Patpet

Patpet 772S Manual de usuario

Patpet

Patpet p-collar 301 Manual de usuario

Manuales populares de Producto para el cuidado de mascotas de otras marcas

Schwinn

Schwinn Rascal Manual de usuario

K&H

K&H Small Animal Manual de usuario

SHOR-LINE

SHOR-LINE 006.3230.00 Manual de usuario

Petsafe

Petsafe Stubborn Dog Receiver Collar Manual de usuario

Datamars

Datamars OMNI MAX Manual de usuario

Trixie

Trixie 24444 Manual de usuario

Roverpet

Roverpet 30DDPP Manual de usuario

SportDOG

SportDOG SD-105S-C Manual de usuario

Staywell

Staywell 400 Series Magnetic Manual de usuario

Dogtek

Dogtek Sonic Birdhouse Manual de usuario

Togfit

Togfit Deluxe Trigger Lock Door Gate Manual de usuario

Girafus

Girafus 227PA Manual de usuario

ubbink

ubbink KoiFeeder Solar Manual de usuario

ULTRACOM

ULTRACOM KOIRA-GPS Manual de usuario

CADOCA

CADOCA Deuba 106911 Manual de usuario

Dogtra

Dogtra RR Deluxe Manual de usuario

Carson

Carson CONVERTIBLE PET YARD 2200 Manual de usuario

Creative Cedar Designs

Creative Cedar Designs K-9 Kabin Manual de usuario

Patpet p-collar 310 Guía de configuración

Manuales populares de Producto para el cuidado de mascotas de otras marcas