Passione 3D MB339 Guía del usuario
MB339 – Mounting instruction
Materials / items required for assembly:
- Bonding/glue: Cyanoacrylate medium, activator for cyanoacrylate and cyan spouts dispensers;
- Finishing sandpaper 500/3 0
- Carbon tube diameter 8 mm
- Carbon tube diameter 4 mm
- Carbon tube diameter mm
- Alcol etilico
- Ethyl alcohol
- Cloth for ethyl alcohol (for cleaning surfaces to be bonded)
Preparative surfaces before bonding:
The MB339 model is composed of several sections, which need to be glued together
Each section before being glued must be sanded very quickly to further refine the plan already created by
the press, so that it is smooth and free of debris that might not do well pave surfaces. (Use abrasive paper
500/3 0).
Afterwards degrease with cloth soaked in ethyl alcohol the surfaces before bonding.
The above operations are very fast to perform, are indications to make the perfect job for the KIT assembly.
Use the cyanoacrylate medium to glue the sections between them, to avoid frittering of glue, use the cyan
spouts dispensers for medium cyan and apply the glue in the edge inside of the plane (not to exaggerate
with the amount, the cyanoacrylate on this type of materile has a strong seal and performs as a weld
between the glued parts) use the activator to accelerate the drying of the glue. It is important to use the
activator and nebulize in small quantities to avoid too rapid drying of the glue.
Once pasted section, in the inner part of the fuselage wipe across the board always with cyanoacrylate
medium, the sections have been designed to allow the creation of this bonding also internally in the fuselage.
For facilitate the gluing of fusolsgr, divide the fuselage into two parts as in the following picture:
And then successively glue the two sections as follows:
A practical tip is to drilling the first front section for the front carriage before gluing, see the following photo:
In the particular photo of the assembly of the front retractable machine.
N.B. The kit used by Turnigy for reach trucks has a 45mm diameter wheel on the front landing gear, I
recommend replacing it with a 40mm diameter wheel to give the model the right trim. I also recommend
changing the shock absorber spring because it is very stiff and tends to make the nose bounce too much, so
I recommend using a softer one (in any case, you can still try with the original spring, then consider changing
it).
Assembly of the wings :
Before inserting and gluing the wing sections, I recommend drilling the holes to screw the machines onto
the wing section. It is very important to use a flat head screw of the right length in order to use the entire
internal thickness of the wing where there is the structure that guarantees the right seal to the machine
and the correct anchorage of the carriage. Use screws max 3.5x 5 mm.
Before screwing the machine, insert a washer between the wing hole and the machine, in order to correctly
align the machine with the surface of the wing (see red circles in the photo above).
For convenience, also screw the servos into the housing in the wing, use the cable gland inside the wing for
the wires.
Once the assembly of the two wings is complete, insert them in the central section of the fuselage using a
carbon tube with a diameter of 8mm with a length of 75 cm, and use a carbon tube with a diameter of
mm for the coupling and alignment of the wing, see example in the photo:
The 8mm carbon shaft naturally passes through and takes both wings, if the tube does not pass well in the
hole in the main section, use an 8mm iron drill bit to widen the hole (carbon rods are not all the same, so
the hole can consequently be too precise)
While as regards the mm carbon tube, it must not pass through and must be inserted up to the internal
housing of the main section, in order to avoid it being forward of the fan mouth. The mm tube is
only.used for aligning the wings with respect to the fuselage.
Carbon tube
2mm
C
arbon
tube
8mm
As reported in the previous photo, it is very important to glue all the sections of the wings together and also
on the support surface of the central section of the fuselage, this guarantees the correct functioning of the
whole structure of the wing. servos / landing machines are guaranteed by the internal passage of the cables
in the wing, so there is no need to disassemble the wing.
- Assembly of moving parts :
All the moving parts of the model are designed to house the nylon hinges type 16x 8.5 or alternatively also
the elastic ribbon ones, below a series of illustrative photos:
N.B. lue the wing sections
together and also on the
fuselage with medium cyan
Hinge detail for top photo above and hinge detail wing photo below.
The gluing of the hinges can also be reinforced from the lower part of the moving parts
Glue the two section
s of the
ailerons
Assembly of elevation plane and rudder:
For the mounting of the platforms and the rudder, a 4mm diameter carbon tube (which will pass through
both shelves) and a mm diameter tube which will only be used exclusively for aligning the parts to the
rest of the fuselage, therefore not passing through, are required, see photo:
All parts must be glued together successively with medium cyan.
Aileron and flap glued and aligned
The brackets are already printed on the moving parts, it
is only
necessary to prepare the
servo
tie rod
Otros manuales de Juguete de Passione 3D
