Parkside PSS 310 Manual de usuario

PSS 310

2003

4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 1

Kompernaß Handelsgesellschaft mbH

Burgstraße 21 · D-44867 Bochum Germany)

4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 2





















4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 3

PSS 310 ORBITAL SANDER

For effortless sanding of metal, wood and varnish/paint …

Dear Customer! We are delighted that you have decided to purchase our high quality PSS 310 orbital sander.

Please make sure you familiarise yourself fully with the way the equipment works before you use it for the first

time and that you understand how to handle electrical power tools correctly. Please read the operating

instructions below and the accompanying safety advice carefully. Use the equipment only as

described and for the indicated purposes. By doing this you will be able to work in complete safety and produce

better results. We hope you enjoy using your sander.

PROPER USE

The orbital sander is intended for sanding wood, metal and paint. Always use a sanding sheet and grade that are

suitable for the particular surface you are sanding. The speed selected should also be appropriate.

FEATURES OF THE PSS 310

Clip Handle

Sanding sheet ON / OFF switch

Base Adjuster wheel

Air vents Dust extraction nozzle (Fig.)

Dust bag adapter ,,,= accessories supplied

Paper dust bag

TECHNICAL INFORMATION

Nominal power: 310 W Nominal voltage: 230 V ~ 50 Hz

Low load speed: n 7,000 – 11,000/min Dust extraction system: built-in extraction system /

Orbits: max. approx. 22,000/min or with exterior suction device

Pad size: 225 x 115 mm Weight: 2.25 kg

Orbit: 2.1 mm

Sanding sheet size max: approx.: 280 x 115 mm The A weighted noise level of the equipment is

Protection class: II typically:

Sound pressure level: 70.0 dB(A)

The acceleration value is typically 2.5 m/s2(vibration)

IMPORTANT SAFETY ADVICE

• To be read in conjunction with the advice in the accompanying booklet on safety.

• The sander is not designed for wet sanding and therefore is only to be used for dry sanding

• Do not use the sander on materials containing asbestos

• Look after your health: Wear ear defenders - also wear safety glasses and a breathing /dust mask

• Take note that working with stone and wood can give rise to dusts that can damage your health.

• Always keep the power cable well out of the sander's working area and fed to the rear of the machine.



www.kompernass.com +++ www.kompernass.com +++ www.kompernass.com +++ w

4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 4

OPERATION

Take note of the mains voltage. The voltage must agree with that shown on the identification plate (equipment

shown as 230 V can also be used with 220 V).

SWITCHING ON AND OFF

SWITCH ON SANDER = press switch 

SWITCH OFF SANDER = press switch again

SETTING THE SPEED

You can set the required speed using the adjuster wheel (see Fig ) as required. As the setting depends on

what kind of material you are working with, use the recommendations and examples given in Tips and Tricks.

FITTING THE SANDING SHEETS

Note: before fitting a new sanding sheet, remove dust and dirt from the base .

1. Lift both clips to open them to insert a new sanding sheet or change the sanding sheet for

use on a different material.

2. Push the sanding sheet under the open clip at one end and clamp it securely on the base by

moving the clip down again.

3. Do the same at the other end. Make sure that the sanding sheet is tight against the base. See Figures and .

4. Important! - The holes in the sanding sheet and the base must align for the dust to be extracted through the

base. See Figure .

Different materials need different grades of sanding sheets. To determine which grade is suitable for your work,

please read our recommendation in Tips and Tricks.

DUST EXTRACTION

• DUST EXTRACTION WITH PAPER DUST BAG

Push the paper dust bag on to the adapter . Ensure that the adapter fits correctly into the holder.

Clip the dust bag with the adapter to the side of the sander.

• DUST EXTRACTION WITH VACUUM CLEANER

For dust extraction using a vacuum cleaner use the appropriate connector – see Figure . Attach the adapter to

the end of the vacuum cleaner hose and clip it to the side of the equipment.

MAINTENANCE OF THE ORBITAL SANDER

1. Clean the sander regularly. For the best results do this straight after the work has been completed.

2. Do not allow liquids to get inside the sander. Use a soft cloth for cleaning the housing. Do not use petrol,

solvents or cleaners that may attack the plastic.

3. Air vents must always be clear and clean.



+ www.kompernass.com +++ www.kompernass.com +++ www.kompernass.com +++

4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 5

ADVICE ON WORKING METHODS, TIPS AND TRICKS

• You can use the PSS 310 orbital sander for effortless sanding even on large areas, see Fig. .

• Move the orbital sander in parallel broad circles or in alternate longitudinal and transverse directions.

• Do not press on the orbital sander. This damages the sanding sheets and adversely affects sanding performance.

• From time to time clean the sanding sheet with a vacuum cleaner.

• You do not have to resand any areas when working up to edges. The orbital sander works right into the corners

because its housing is continuous with the edge of the sanding sheet, see Fig. .

• The integrated dust extraction system allows you to work cleanly overhead. Use the integrated dust extraction

system or your vacuum cleaner wherever possible when sanding.

• The choice of speed and grade of sanding sheet determines the sanding performance and therefore the results

of your work.

• Never use the same sanding sheet on different materials (e.g. wood and then metal).

•* For metals we recommend 60 grade (steel) or 80 grade (aluminium) – with a medium to high speed.

•* For wood we recommend 60 grade (hardwood) or 60 – 80 grade (soft wood) with a medium to high speed. If you

are sanding veneered surfaces we recommend 240 grade – with a low to high speed depending on the

smoothness of the finish.

•* When working on varnished/painted surfaces we recommend 120 grade e.g. for smoothing out scratches

(medium to high speed), 180 grade for sanding down (low speed) and 40 grade e.g. for removing rust

(low to middle speed).

• The PSS 310 orbital sander uses HIGH TECHNOLOGY FIXING.

This no-tool quick change feature allows you to work more easily

and quickly. One hand is all that is needed.

•* These are advisory recommendations only. Before you start work, you should carry out a test to see which grade

and speed is most suitable for your work.

Further practical tips for power tools can be found in the accompanying booklet on safety advice.

We reserve the right to make technical modifications in the course of further development.



www.kompernass.com +++ www.kompernass.com +++ www.kompernass.com +++

4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 6

www.kompernass.com +++ www.kompernass.com +++ www.kompernass.com +++

STATEMENT OF CONFORMITY

We, Kompernaß Handelsgesellschaft mbH, Burgstr. 21, D-44867 Bochum, Germany, hereby declare

that this product conforms with the following EC regulations:

(98/37 EWG)

EC low voltage regulations: (73/23/EEG), (93/68 EEG)

Electromagnetic compatibility: (89/336 EEG), (92/31 EEG), (93/68 EEG)

Applicable harmonised standards:

Type: Orbital sander PSS 310

Bochum, 31.05.2003

Hans Kompernaß

- Managing Director -



4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 7





WARRANTY

This piece of equipment is covered by a 3-year warranty as of the date of purchase. The equipment was produced

with the greatest of care and underwent thorough testing before delivery. In the unlikely event of detecting a

functional defect, please return the equipment in its original packaging with the proof of purchase to the closest

service address. Damage caused due to improper handling as well as regular wear of the parts are not covered by

this warranty.

Beaver Electronic Services · The Lodge, Premier Business Park

Long Street, Walsall · West Midlands, WS2 9DY

Tel.: 08707876177 · Fax: 01922/725417

WARRANTY

This piece of equipment is covered by a 3-year warranty as of the date of purchase. The equipment was produced

with the greatest of care and underwent thorough testing before delivery. In the unlikely event of detecting a

functional defect, please return the equipment in its original packaging with the proof of purchase to the closest

service address. Damage caused due to improper handling as well as regular wear of the parts are not covered by

this warranty.

Irish Web Specialists · 1 Verbena Avenue · Dublin 13

Tel.: 01/8320492 · Fax: 01/8396829

4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 8

www.kompernass.com

ORFGEN Marketing & Communication

Essen · Germany

4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 9

www.kompernass.com

ORFGEN Marketing & Communication

Essen · Germany

4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 10

Tabla de contenidos

Otros manuales de Lijadora de Parkside

Parkside

Parkside PMFS 200 B2 Manual de usuario

Parkside

Parkside PMS 130 Manual de usuario

Parkside

Parkside PDEXS 150 C2 Manual de usuario

Parkside

Parkside KH 3020 BELT SANDER Manual de usuario

Parkside

Parkside PSR 310 A1 Manual de usuario

Parkside

Parkside PDAP 75 A1 Manual de usuario

Parkside

Parkside PDS 290 A1 Manual de usuario

Parkside

Parkside PEXS 270 C3 Manual de usuario

Parkside

Parkside PAEXS 20-Li A1 Manual de usuario

Parkside

Parkside PBS 900 C3 Manual de usuario

Parkside

Parkside PAEXS 20-Li A1 Manual de usuario

Parkside

Parkside PPMA 20-Li B2 Manual de usuario

Parkside

Parkside PDS 290 B2 Manual de usuario

Parkside

Parkside PDS 290 AI Manual de usuario

Parkside

Parkside PDS 290 B2 Manual de usuario

Parkside

Parkside XQ90 - MANUEL 2 Manual de usuario

Parkside

Parkside PHS 160 A1 Manual de usuario

Parkside

Parkside KH 3032 BELT SANDER 600 WATT Manual de usuario

Parkside

Parkside PHS 160 B2 Manual de usuario

Parkside

Parkside PEXS 270 Al Manual de usuario

Parkside

Parkside PBS 600 A1 Manual de usuario

Parkside

Parkside 315148 Guía rápida

Parkside

Parkside 373087 2104 Manual de usuario

Parkside

Parkside PEXS 270 C3 Manual de usuario

Manuales populares de Lijadora de otras marcas

Oliver

Oliver 6305 Manual de usuario

Jet

Jet 22-44 Pro-3 Manual de servicio

Makita

Makita M9204 Manual

Makita

Makita M9204 Manual de usuario

Craftsman

Craftsman 351.215131 Manual de usuario

Clarke

Clarke Woodworker CBS1-5B Manual de instrucciones

Chicago Pneumatic

Chicago Pneumatic CP9778 Manual de usuario

Nitto Kohki

Nitto Kohki BB-20 Manual de usuario

Ferm

Ferm FEOS-135 Manual de usuario

Unior

Unior 1510 Manual de usuario

stayer

stayer ls1200 Manual de usuario

Jet

Jet JSG-96 Manual de servicio

Status

Status XPA Series Manual de usuario

Clarke

Clarke EZ Sand Manual de usuario

Craftsman

Craftsman 113.22521 Manual de usuario

Craftsman

Craftsman 113.225831 Manual de usuario

CLAS

CLAS OP 1429 Manual de usuario

Makita

Makita 9207SPB Manual de usuario