Parkside PGG 15 A1 Manual de usuario
POWER ENGRAVING TOOL PGG 15 A1
7
POWER ENGRAVING TOOL
Operation and Safety Notes
Translation of original operation manual
Η
ΛΕΚΤΡΙΚΗ ΣΥΣΚΕΥΗ ΧΑΡΑΚΤΙΚΗΣ
Υποδείξεις χειρισμού και ασφαλείας
Μετάφραση των αυθεντικών οδηγιών λειτουργίας
GRAVIERGERÄT
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
UREĐAJ ZA GRAVIRANJE
Upute za posluživanje i za Vašu sigurnost
Prijevod originalnih uputa za uporabu
APARAT DE GRAVURĂ
Instrucţiuni de utilizare şi de siguranţă
Traducerea instrucţiunilor de utilizare originale
УРЕД ЗА ГРАВИРАНЕ
Инструкции за обслужване и безопасност
Превод на оригиналното ръководство за експлоатация
66133_Mini-Graviergerät_cover_LB7.indd 6 01.06.11 15:28
GB/CY Operation and Safety Notes Page 5
HR Upute za posluživanje i za Vašu sigurnost Stranica 21
RO Instrucţiuni de utilizare şi de siguranţă Pagina 37
BG Инструкции за обслужване и безопасност страница 53
GR/CY Υποδείξεις χειρισμού και ασφαλείας Σελίδα 69
DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 85
Before reading, unfold the page containing the illustrations and familiarise yourself with all
functions of the device.
Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa
svim funkcijama uređaja.
Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.
Преди да прочетете отворете страницата с фигурите и след това се запознайте с
всички функции на уреда.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις
λειτουργίες της συσκευής.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich
anschließend mit allen Funktionen des Gerätes vertraut.
УРЕД ЗА ГРАВИРАНЕ
Инструкции за обслужване и безопасност
Превод на оригиналното ръководство за експлоатация
66133_Mini-Graviergerät_cover_LB7.indd 7 01.06.11 15:28
B
1 2 3
45
6
A
7
66133_Mini-Graviergerät_cover_LB7.indd 8 01.06.11 15:28
66133_Mini-Graviergerät_cover_LB7.indd 9 01.06.11 15:28
5GB/CY
Table of contents
Introduction
Proper use..............................................................................Page 7
Features and equipment.......................................................Page 7
Included items ....................................................................... Page 8
Technical details....................................................................Page 8
General safety advice for
electrical power tools
1. Workplace safety ............................................................. Page 9
2. Electrical safety ................................................................. Page 10
3. Personal safety.................................................................. Page 11
4. Careful handling and use of electrical power tools ....... Page 12
Operation
Switching on/off ..................................................................Page 13
Setting the stroke rate ...........................................................Page 14
Changing the engraving point ............................................. Page 14
Advice on use........................................................................Page 15
Cleaning .............................................................................Page 15
Service.................................................................................Page 15
Warranty...........................................................................Page 16
Disposal..............................................................................Page 17
Manufacturer’s Declaration of
Conformity/Manufacturer................................. Page 18
66133_Mini-Graviergerät_content_LB7.indd 5 03.06.11 16:57
6 GB/CY
Introduction
Introduction
The following pictograms are used in these operating
instructions/on the device:
Read instruction manual!
V~Volt (AC)
AAmps
Observe caution and safety notes!
Risk of explosion!!
Keep children away from electrical power tools!
Caution–electric shock! Danger to life!
Risk of loss of life by electric shock from damaged mains
lead or mains plug!
Wear hearing protection, dust protection mask, protective
glasses and protective gloves.
Dispose packaging and appliance in an environmen-
tally-friendly way!
66133_Mini-Graviergerät_content_LB7.indd 6 03.06.11 16:57
7GB/CY
Introduction
Power engraving tool PGG 15 A1
Introduction
Please make sure you familiarise yourself fully with the way
the device works before you use it for the first time and that
you understand how to handle electrical power tools correctly.
To help you do this please read the accompanying operating instructions.
Keep these instructions in a safe place. If you pass the device on to an-
yone else, please ensure that you also pass on all the documentation.
Proper use
This product is intended for engraving or decorating materials such
as metal, plastic, glass, ceramic, wood and leather. Any other use or
modification to the drill/grinder shall be considered as improper use
and could give rise to considerable dangers. The manufacturer will not
accept liability for loss or damage arising from improper use. Not
intended for commercial use.
Features and equipment
1ON/OFF switch
2Stroke switch
3Hanging eye
4Mains lead
5Engraving point
6Engraving point holder
7Engraving stencils
66133_Mini-Graviergerät_content_LB7.indd 7 03.06.11 16:57
8 GB/CY
Introduction/General safety advice for electrical power tools
Introduction
Included items
1 Power engraving tool PGG 15 A1
2 Engraving stencils
1 Operating instructions
Technical details
Rated voltage: 230V∼ 50Hz
Mode of operation: intermittent operation: S3 20%
Rated current: 0.15A
Stroke rate: 6000min-1
Noise and vibration data:
Measured values for noise are determined in accordance with
EN 60745. The A-weighted noise level of the electrical power tool
are typically:
Sound pressure level: 74.4dB(A)
Sound power level: 85.4dB(A)
Uncertainty K: 3dB
Wear ear protection!
Evaluated acceleration, typical:
Hand/arm vibration: 1.582m/s2
Uncertainty K = 1.5m/s2
The vibration level given in these instructions has
been measured in accordance with a standardised measurement pro-
cedure specified in EN 60745 and can be used to compare devices.
66133_Mini-Graviergerät_content_LB7.indd 8 03.06.11 16:57
9GB/CY
Introduction/General safety advice for electrical power tools
Different uses of the device give rise to different vibration levels and in
many cases they may exceed the values given in these instructions. It is
easy to underestimate the vibration load if the electrical power tool is
used regularly in particular circumstances.
Note: If you wish to make an accurate assessment of the vibration
loads experienced during a particular period of working, you should
also take into account the intervening periods of time when the device
is switched off or is running but is not actually in use. This can result in
a much lower vibration load over the whole of the period of working.
General safety advice for
electrical power tools
Read all the safety advice and instruction
s!
Failure to observe the safety advice and instructions may result in electric
shock, fire and/or serious injury.
Keep all the safety advice and instructions in a safe place
for future reference!
The term “electrical tool” used in the safety advice refers to electrical
tools powered by mains electricity (by means of a mains lead) and elec-
trical tools powered by rechargeable batteries (without a mains lead).
1. Workplace safety
a) Keep your working area clean and well lit. Untidy or
poorly lit working areas can lead to accidents.
66133_Mini-Graviergerät_content_LB7.indd 9 03.06.11 16:57
10 GB/CY
General safety advice for electrical power tools
b) Do not work with the device in potentially
explosive environments in which there are
inflammable liquids, gases or dusts. Electrical
power tools create sparks, which can ignite dusts or fumes.
c) Keep children and other people away while
you are operating the electrical tool. Distrac-
tions can cause you to lose control of the device.
2. Electrical safety
a)
T
he mains plug on the device must match the mains
socket. The plug must not be modified in any way.
Do not use an adapter plug with devices fitted with
a protective earth. Unmodified plugs and matching sockets
reduce the risk of electric shock.
b) Avoid touching earthed surfaces such as pipes, radia-
tors, ovens and refrigerators with any part of your
body. There is an increased risk of electric shock if your body is
earthed
.
c) Keep the device away from rain or moisture. Water en-
tering an electrical device increases the risk of electric shock.
d) Do not use the mains lead for any purpose for
which it was not intended, e.g. to carry the de-
vice, to hang up the device or to pull the mains
plug out of the mains socket. Keep the mains lead
away
from heat, oil, sharp edges or moving parts of the
device. Damaged or tangled mains leads increase the risk of
electric shock.
e) When working outdoors with an electrical power tool
always use extension cables that are also approved
66133_Mini-Graviergerät_content_LB7.indd 10 03.06.11 16:57
Otros manuales para PGG 15 A1
15
Tabla de contenidos
Idiomas:
Otros manuales de Herramientas eléctricas de Parkside
Parkside
Parkside PMNF 1500 A1 Manual de usuario
Parkside
Parkside PMFW 280 A1 - 5 Manual de usuario
Parkside
Parkside PT370 Manual de usuario
Parkside
Parkside PSTKA 12 B3 Manual de usuario
Parkside
Parkside PHKSA 18-Li B2 Manual de usuario
Parkside
Parkside 93548 Manual de usuario
Parkside
Parkside PBSG 95 B1 Manual de usuario
Parkside
Parkside PMNF 1350 A1 Manual de usuario
Parkside
Parkside PDSP 1000 B2 Manual del propietario
Parkside
Parkside PAMFW 10.8 A1 Manual de usuario
Parkside
Parkside 406362 2207 Manual de usuario
Parkside
Parkside PDSP 1000 D5 Manual de usuario
Parkside
Parkside 360583 2010 Manual de usuario
Parkside
Parkside 373198 2104 Manual de usuario
Parkside
Parkside PSSSA 20-Li B2 Manual de usuario
Parkside
Parkside 86585 Manual de usuario
Parkside
Parkside PHLG 2000 B1 Manual de usuario
Parkside
Parkside PEC 200 SE - 4 Manual de usuario
Parkside
Parkside PSTDA 18-Li B2 Guía de inicio rápido
Parkside
Parkside KH 3050 ELECTRIC NAILER Manual de usuario
