Panmobil smartSCANNDY II Manual de usuario
SCANNDY USER GUIDE
Page 1
smartSCANNDY
Quick Reference Guide
SCANNDY USER GUIDE
Page 2
© 2014 by advanced PANMOBIL systems GmbH & Co. KG
This manual contains proprietary information of advanced PANMOBIL systems GmbH &
Co. KG. It is intended solely for the information and use of parties operating and
maintaining the equipment described herein. Such proprietary information may not be
used, reproduced, or disclosed to any other parties for any other purpose without the
expressed written permission of advanced PANMOBIL systems GmbH & Co. KG.
Software and product improvement
The software is provided strictly on an “as is” basis. The user shall not modify, merge,
or corporate any form or portion of a licensed program with other program material,
create a derivative work from a licensed program, or use a licensed program in a
network without written permission from PANMOBIL. The user agrees not to
decompile, disassemble, decode, or reverse engineer any program delivered to the
user or any portion thereof. PANMOBIL reserves the right to make changes to any
software or product to improve reliability, function, or design. PANMOBIL does not
assume any product liability arising out of, or in connection with, the application or use
of any product, circuit, or application described herein. No license is granted, either
expressly or by implication, estoppel, or otherwise under any PANMOBIL intellectual
property rights. An implied license only exists for equipment, circuits, and subsystems
contained in PANMOBIL products.
Trademarks
PANMOBIL and smartSCANNDY are registered trademarks. Bluetooth is a registered
trademark of Bluetooth SIG. Microsoft and Windows are either registered trademarks
or trademarks of Microsoft Corporation. All other product or service names are the
property of their respective owners.
advanced PANMOBIL systems GmbH & Co. KG
Hansestraße 91
D-51149 Cologne, Germany
Warranty
For the complete PANMOBIL hardware product warranty statement,
go to: www.PANMOBIL.com
SCANNDY USER GUIDE
Page 3
PRODUCT REFERENCE
smartSCANNDY II
Introduction
PANMOBIL smartSCANNDY devices capture and store barcode and RFID data for a
variety of uses, and transmit barcode and RFID data to a host via USB connection,
Bluetooth or Wi-Fi. This document provides basic instruction using the smartSCANNDY
device. For information about settings and configurations, please refer to the product
user manual on www.PANMOBIL.com
1
2
3
4
7
5
6
8
4
7
SCANNDY USER GUIDE
Page 4
No.
Description
Function
1
Left LED (green)
Left LED (red)
Green LED: Lights up green when the device is turned ON.
When the battery level is empty, it flashes every 2 sec
(Further function can be user defined with the programming
interface)
Red LED: Lights up red if connected to a battery charger (USB
or power adapter)
2
Right LED (yellow)
Right LED (blue)
Yellow LED:
Lights up yellow if a barcode or RFID tag was read
successfully.
Is flashing yellow (500ms) when connected to USB (USB
Memory stick mode)
(Further function can be user defined with the programming
interface)
Blue LED:
Lights up blue if Bluetooth connection is established
(Further function can be user defined with the programming
interface)
3
Key 1 (Trigger Barcode or
RFID reader)
Default: Triggers the barcode and/or the RFID reader
(This function can be configured by using Universal
Configurator or
with the programming interface)
4
Key 2 (custom)
(This function can be configured by using Universal
Configurator or
with the programming interface)
5
Key Power ON/OFF
Default: ON/OFF button
Device OFF: press this button to switch ON
Device ON: press for 3 sec. to switch the device OFF
(This function can be configured by using Universal
Configurator or
with the programming interface)
6
Configuration Mode
Alternative configuration mode
Follow the instructions below to set the configuration mode
1. Switch Off the device
2. Press and hold button 4 and button 5 until you hear a
beep. (this may take a few seconds)
3. Connect the device to a computer via USB
4. The device will be mounted as a removable drive
“SCANNDY”
5. Open the fie “config.ini” or use the Universal
Configurator to modify the settings
SCANNDY USER GUIDE
Page 5
6. Press button 3 (Trigger) until a beep sound appears
7. The device restarts with the new settings
7
USB protection cap
Protects the USB interface from damages.
Press both PANMOBIL logos on both sides to release the USB
cap and access the USB connector
No.
Description
Function
8
Battery cover
Turn the button 90° to open the battery cover and access the
battery compartment
9
Clip holder (accessories)
Holder to fix the shirt clip, belt clip or neck belt (accessories)
10
PDA stylus
Stylus for the touch panel
8
9
10
11
12
13
SCANNDY USER GUIDE
Page 6
11
Contacts AAA batteries
Battery contacts for standard AAA batteries.
DO NOT USE RECHARGEABLE AAA BATTERIES!
WATCH OUT FOR THE POLARITY
12
Contacts for charging the
Li-Ion battery
Battery contacts for charging the Li-Ion battery
BE CAUTION TO NOT DAMAGE THIS PINS WHEN INSERTING
THE RECHARGEABLE BATTERIES WATCH OUT FOR THE
POLARITY
13
Product Label
Product and serial number label (under the batteries)
No.
Description
Function
14
RFID Antenna (option)
Antenna for RFID reader/writer
15
Protection glass for
barcode and RFID
reader
Protection glass for the barcode and RFID reader. To have the
best reading performance, keep the glass clean and free of
scratches.
16
USB (device) interface
USB (device) interface
2
14
15
16
SCANNDY USER GUIDE
Page 7
CHARGING THE BATTERY
Before the first operation, the main battery should be charged by using the
included power adapter or through the USB interface of the computer. As long
as the battery is charging, the red LED (1) lights solid red. After the battery is
fully charged the red LED (1) turns off.
Please insert the
rechargeable batteries
with this site first
SCANNDY USER GUIDE
Page 8
1. Remove the USB protection cap (7) from the device
2. Connect the device to the USB port of a computer or to the USB power
adapter (accessories)
3. As long as the battery is charging, the red LED (1) lights solid red
4. After the battery is fully charged the red LED (1) turns off.
A full recharge of the battery takes approximately 4 to 5 hours when using the
included power adapter. Recharging the battery from a USB interface of a
computer may take longer.
SCANNDY USER GUIDE
Page 9
SCANING BARCODE (1D Laser)
1. Aim the scanner on the barcode
2. Press the Trigger button (3)
3. Ensure that the scanning line is directed straight on the barcode
The device beeps and the right LED (2) turns green to indicate a successful decode.
Take a look at the smartSCANNDY user guide to see how to define beeps and vibrate
alerts by using the Universal Configurator.
SCANNDY USER GUIDE
Page 10
SCANING BARCODE (1D/2D Imager)
1. Aim the scanner on the barcode
2. Press the Trigger button (3)
3. The device decodes the code nearest to the cross centre unless you
disable the Pick-List mode (see below) in the 2D cameras.
1. Replace the Config.INI
Please download the following file
(Right click and "save as"):
Config.INI
Please copy it to the device and replace the existing .After restart of
the device the Pick List Mode is now turned off.
2. Manually change the config file:
a. Connect the device to your computer
b. Open drive "SCANNDY"
c. Open "Config.INI" on the drive
d. Set Pick list Mode=0
e. Save the changes
f. Disconnect device from USB and reboot
Tabla de contenidos
Otros manuales de Lector de código de barras de Panmobil
