Panduit T568B Manual de usuario

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

Page 1 of 4

TX6A Shielded Modular Plug

T568B & T568A

Part Number: SPS6X88-C

• Thread boot and collar onto cable.

• Remove 1.5" of the outer jacket using wire stripping tool

(CJAST).

• Cut foil flush with cable jacket. If cable is braided, form braid

into a drain wire. Bend the drain wire back so it is against the

cable jacket.

• Fan twisted pairs into respective quadrants. The brown pair

should be opposite the orange pair.

• Cut spline flush to fanned pairs using wire snipping tool

(CWST).

1Thread on boot

and collar first!

(Cable ends 1 & 2)

90°

CWST

Specifications

•Cable jacket diameter maximum 0.300 in (7.6mm).

•Solid or stranded conductor maximum insulated diameter

0.047 in (1.2mm).

•Panduit recommends T568B wiring scheme for use with

cable constructed with the brown pair opposing the orange

pair.

•For use with F/UTP, U/FTP and S/FTP type cables, which

meet the dimensional requirements. Cable must have drain

wire or braid.

Conductor holes and contact slots

Strain relief boot

Strain relief collar

Divider

Load bar

Plug housing with shield

Load Bar

Divider

Conductor slots and “V” channel

• Align the conductor divider “V” channel with the green pair.

• Insert divider posts into the cable. If the cable has an internal

spline, insert divider posts into the brown and orange

quadrants of the spline.

BLU

GRN

“V” channel

BRN

ORG

GRN

BLU

BRN

ORG

(Cable end 2)

(Cable end 1)

“V” channel

Drain wire

• Arrange conductors to T568B wiring scheme while minimizing

untwist.

• Seat conductors into proper divider slots while holding divider

flush with cable jacket.

“V” channel

(Cable end 1) (Cable end 2)

T568B Wiring Scheme

T568B BRN

WHT

BRN/

GRN WHT

BLU/

BLU WHT

GRN/

ORG WHT

ORG/

Pin #

(Cable end 2)

(Cable end 1)

“V” channel

Conductor holes

Contact slots Divider post

Pins

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

Page 2 of 4

• Guide conductors into load bar holes while holding

conductors in the divider.

• Slide load bar towards divider until flush.

• Ensure the divider/load bar is centered and perpendicular to

the cable axis.

• Trim conductors flush with load bar face.

(Cable end 1)

• Orient load bar with contact slots facing downward.

Verify

load bar

orientation

(Cable end 1)

(Cable end 2)

Pins

• Straighten and align untwisted conductors using a circular

motion while holding conductors in respective divider slots.

• Maintain grip of conductors in T568B wiring scheme.

• Trim conductors on an angle approximately 1.00" from

divider leading edge.

1.00"

T568B BRN

WHT

BRN/

GRN WHT

BLU/

BLU WHT

GRN/

ORG WHT

ORG/

Pin #

(Cable end 1)

10 MPT5-8AS

Plug

housing

• Grip the strain relief collar and insert cable sub-assembly into

the plug housing. (Fig. 9)

• Push sub-assembly into housing until collar locking tabs

engage the plug housing pocket. Although not required, TX6

PLUS Plug Assembly Tool (CSPT) is available to facilitate this

step.

• Use tool MPT5-8AS to complete plug termination. (Fig. 10)

• Trim or press excess drain wire between the collar latches.

• Push up boot and engage with collar latches.

• Visually check plug. Assembly is complete.

Drain wire

(Cable end 2)

(Cable end 1)

Strain collar

guides

Collar latches

Boot position

when using

CSPT

Pins

Collar barbs

Pins

Collar locking

tabs

• Orient cable so the drain wire is facing up.

• Hold the load bar and divider stationary while sliding the strain

relief collar forward until there is no gap between the collar

and divider.

• Ensure the drain wire is routed through the strain collar

guides.

• Confirm the cable jacket extends beyond the collar barbs.

• Align pin #1 of cable sub-assembly (cable, load bar, divider,

and strain relief collar) with pin #1 of plug housing.

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

Page 3 of 4

T568A Wiring Scheme

T568A BRN

WHT

BRN/

ORG WHT

BLU/

BLU WHT

ORG/

GRN WHT

GRN/

Pin #

• The “V” channel should be aligned with the orange pair.

• Insert divider posts into the cable. If the cable has an internal

spline, insert divider posts into the brown and green quadrants

of the spline.

BLU

ORG

“V” channel

BRN

GRN

ORG

BLU

BRN

GRN

(Cable end 2)

(Cable end 1)

“V” channel

Drain wire

• Arrange conductors to T568A wiring scheme while

minimizing untwist.

• Seat conductors into proper divider slots while holding divider

flush with cable jacket.

“V” channel

(Cable end 1) (Cable end 2)

Conductor holes and contact slots

Load Bar Divider

Conductor slots and “V” channel

“V” channel Divider post

Conductor holes

Contact slots

Pins

Strain relief boot

Strain relief collar

Divider

Load bar

Plug housing with shield

(Cable end 2)

(Cable end 1)

• Thread boot and collar onto cable.

• Remove 1.5" of the outer jacket from the cable end using wire

stripping tool (CJAST).

• Cut foil flush with cable jacket end. If cable is braided, form

into a drain wire. Bend the drain wire back so it is against the

cable jacket.

• Fan twisted pairs into respective quadrants. The brown pair

should be opposite the green pair.

• When a cable spline (X-shaped filler) is present, cut spline

flush to fanned pairs using wire snipping tool (CWST).

1Thread on boot

and collar first!

(Cable ends 1 & 2)

90°

CWST

Specifications

•Cable jacket diameter maximum 0.300 in (7.6mm).

•Solid or stranded conductor maximum insulated diameter

0.047 in (1.2mm).

•Panduit recommends T568A wiring scheme for use with

cable constructed with the brown pair opposing the green

pair.

•For use with F/UTP, U/FTP and S/FTP type cables, which

meet the dimensional requirements. Cable must have drain

wire or braid.

INSTALLATION INSTRUCTIONS

E-mail:

[email protected]m

Phone:

866-405-6654

For Instructions in Local Languages

and Technical Support:

www.panduit.com/resources/install_maintain.asp www.panduit.com

Page 4 of 4

1.00"

T568A BRN

WHT

BRN/

ORG WHT

BLU/

BLU WHT

ORG/

GRN WHT

GRN/

Pin #

(Cable end 1)

• Straighten and align untwisted conductors using a circular

motion while holding conductors in respective divider slots.

• Maintain grip of conductors in T568A wiring scheme.

• Trim conductors on an angle approximately 1.00" from

divider leading edge.

(Cable end 1)

(Cable end 2)

Pins

Verify

load bar

orientation

Pins

• Orient load bar with contact slots facing downward.

(Cable end 1)

• Guide conductors into load bar holes while holding

conductors in the divider.

• Slide load bar towards divider until flush.

• Ensure the divider/load bar is centered and perpendicular to

the cable axis.

• Trim conductors flush with load bar face.

10 MPT5-8AS

housing

Plug

• Grip the strain relief collar and insert cable sub-assembly into

the plug housing. (Fig. 9)

• Push sub-assembly into housing until collar locking tabs

engage the plug housing pocket. Although not required, TX6

PLUS Plug Assembly Tool (CSPT) is available to facilitate this

step.

• Use tool MPT5-8AS to complete plug termination. (Fig. 10)

• Trim or press excess drain wire between the collar latches.

• Push up boot and engage with collar latches.

• Visually check plug. Assembly is complete.

Drain wire

(Cable end 2)

(Cable end 1)

Strain collar

guides

Collar latches

Boot position

when using

CSPT

Pins

Collar barbs

Pins

Collar locking

tabs

• Hold the load bar and divider stationary while sliding the strain

relief collar forward until there is no gap between the collar

and divider.

• Ensure the drain wire is routed through the strain collar

guides.

• Confirm the cable jacket extends beyond the collar barbs.

• Align pin #1 of cable sub-assembly (cable, load bar, divider,

and strain relief collar) with pin #1 of plug housing.

Este manual sirve para los siguientes modelos

Otros manuales de Cables y conectores de Panduit

Panduit

Panduit DPA245E88TV25 Manual de usuario

Panduit

Panduit PND110 Manual de usuario

Panduit

Panduit PAN-SHRINK HSTTT Series Manual de usuario

Panduit

Panduit IAEBH5E Manual de usuario

Panduit

Panduit VeriSafe VSC Series Manual de usuario

Panduit

Panduit KMTRTH Manual de usuario

Panduit

Panduit FS148 Manual de usuario

Panduit

Panduit CHD15HDSC Y Series Manual de usuario

Panduit

Panduit CT-1000 Hoja de especificaciones

Panduit

Panduit FSCMM Series Manual de usuario

Panduit

Panduit CRB6BL Manual de usuario

Panduit

Panduit CM308F Guía de configuración

Panduit

Panduit VeriSafe VS-CKP14-6 Manual de usuario

Panduit

Panduit TX5e Manual de usuario

Panduit

Panduit FK2BJ Manual de usuario

Panduit

Panduit FLCSHMIG Manual de usuario

Panduit

Panduit CJS588T Manual de usuario

Panduit

Panduit FJJGM2.0C Manual de usuario

Panduit

Panduit PN366E Manual de usuario

Panduit

Panduit NetKey 6 Series Manual de usuario

Panduit

Panduit T568A Manual de usuario

Panduit

Panduit DP6 PLUS Manual de usuario

Panduit

Panduit Opti-Core Manual de usuario

Panduit

Panduit FO6CB Manual de usuario

Manuales populares de Cables y conectores de otras marcas

Philips

Philips SWA6310 Manual de usuario

StarTech.com

StarTech.com CRJ4550PK Manual de usuario

Nohau

Nohau EMUL-IP2K-PC Manual de usuario

Foxun

Foxun SX-SP144E-HD4K2K Manual de usuario

Philips

Philips SWA3305W Manual de usuario

opticis

opticis Stretch DVIM1-1P0x Manual de usuario

Volkswagen

Volkswagen VAS 6558A Manual de usuario

NEXIBO

NEXIBO N-13 Manual de usuario

CYP

CYP PU-1H3HBTL Manual de usuario

Allen-Bradley

Allen-Bradley 1784-u2dhp Manual de usuario

Global Caché

Global Caché Flex Link Blaster Manual de usuario

Hauppauge

Hauppauge USB-Live2 Manual de usuario

Fenix

Fenix MPSV 15 Manual de usuario

BEGA

BEGA 71 085 Manual de usuario

Tesla

Tesla HPWC Manual de usuario

GAMERON

GAMERON LUXURY TV CABLE Manual de usuario

molex

molex Milli-Grid Dual row 87568 Series Manual de usuario

Burndy

Burndy Continental Industries thermOweld CRE-7 Manual de usuario