Panasonic NV-FJ603EL-K Manual de usuario

ORDERNO. VRD0002003C2

Video Cassette Recorder

NV-FJ603EL-K / NV-FJ603EP-K / NV-FJ603EPYK / NV-

FJ604EG-K / NV-FJ604ECMK / NV-FJ606EG-K / NV-

FJ606EGYK / NV-FJ606EC-K / NV-FJ606ECMK / NV-FJ611B-

Z-MECHANISM

SPECIFICATIONS

Unauthorized copying and distribution isaviolation of law.

1. INTRODUCTION

This service manual contains technical information whichwill allowservice personnel to

understand and service this model.

If the circuit is changedormodified, this information will be followedbysupplementaryservice

manual tobe filedwithoriginal service manual.

Note 1 :

Adjustment procedures, DisassemblyProcedures and AssemblyProcedures forMechanism

Chassis are separate volume fromthis service manual. / Please refertothe service manual forZ-

MechanismChassis. (OrderNo. VRD9802005C2)

Note 2 :

The Model No. is indicatedon the Schematic Diagramand Circuit BoardDiagrams as follows.

Model No. FJ604EG-K FJ606EG-K FJ610EG-S/

KFJ606EGYK FJ610EGYS/

KFJ610B-S/K

FJ611B

Indication

Mark (A) (A) (A) (B) (B) (C)

(

Model No. FJ604ECMK FJ606EC-K FJ606ECMK FJ610EC-S/

KFJ610ECMS

/K FJ610ECYS/

FJ610BL

Indication

Mark (D) (D) (D) (D) (D) (E)

Model No. FJ603EL-K FJ603EP-K FJ603EPYK

Indication

Mark (G) (H) (J)

2. GENERAL DESCRIPTIONS

2.1. SERVICEINFORMATION

2.1.1. CHANNELMEMORY IC INITIALIZATION

Whenreplacing the MemoryIC7704 and/orOscillatorX6001, MemoryIC7704 has tobe initialized

due tothe setting value changes.

Note:

1. When replacing the memoryIC7704, the OSDmicroprocessor

IC7703 shouldbe replaced together.

2. Ithas to be performed before tuning.

3. Meaning of “MEMORYICINITIALIZATION"isto make dependency

indifferent modelsand to distinguish between different features.

4. Itdoes not need to perform when replacing the System Control

IC6001.

PROCEDURES FIP Display Monitor

Screen

Press the FF and EJECTkeys simultaneouslyfor3

seconds. None

Press the FF and EJECTkeys simultaneouslymore

twice. None

Press the EJECTkeyfor3 seconds. None

Press the CH UP keytwice. None

Press the POWER key.

(Colon starts flashing)

Service Screen(

See

Service Screen (

Sample)

Press the REC keyon the Remote ControllerUnit. Service Screen(

See

Service Screen (

Sample)

Set the Model Code and Option Code bypressing 10

-keyor[RIGHT] [LEFT] [UP] [DOWN] keys on the

Remote ControllerUnit. (See Fig. S2)

Service Screen(

See

Service Screen (

Sample)

To release Service Mode, press POWER keyand

thenpress FF orturnthe shuttle ring tothe FF and

press EJECTkeysimultaneously6 times until the

normal indication on the FIP.

None

Fig. S1 Service Screen(Sample)

Caution :

Since the “Clock adjust” and “VPS/PDC default” are future

expansion, do not change the initial settings.

Just incase, ifthese initial setting values had been changed

accidentally, itcan be recovered bypressing [UP] [DOWN]keyson

the Remote Controller.

Model No. Suffix Model

CodeOption

Code

Option

Code

Option

Code

NV-FJ603 EL-K 41 253 64 140

NV-FJ603 EP-K/EPYK 45 253 64 140

NV-FJ604 ECMK 45 141 64 140

NV-FJ604 EG-K 41 141 64 140

(To be continuedon next page.)

Model No. Suffix Model

CodeOption

Code

Option

Code

Option

Code

NV-FJ606 EC-K/ECMK 45 141 64 140

NV-FJ606 EG-K/EGYK 41 141 64 140

NV-FJ610 B-K/B-S 49 161 64 140

NV-FJ610 BL-S 4D 161 64 140

NV-FJ610 EC-S/EC-K/

ECMS/ECMK/

ECYS/ECYK

45 137 64 140

NV-FJ610 EG-S/EG-K/

EGYS/EGYK 41 137 64 140

NV-FJ611 B-K 49 165 64 140

Fig. S2 Model Code & Option Code

2.1.2. CAUTION FOR AUTO TUNING

PROCEDURE

AutoTuning will start bythe following procedure.

1. Connect the DIN-RFCable.

2. Connect the AC Mains Lead.

3. Turn on the VCR. / Auto Tuning will start. / Auto Tuning searches

for TV stations from VHFminimum to UHFmaximum and

memorizes everytuned program position. Other program

positions are skipped.

Auto Tuning takes five or more minutes to complete its search.

Donot touch the VCR during Auto Tuning.

Auto Tuning will stop halfway, ifthe VCR isoperated or the aerial

lead and/or the mains lead are disconnected.

Incase the VCR stopped during Auto Tuning, the VCR have to be

reset and restarted. See the following item 2.

NOTE

1. Ifthe VCR isturned on with the antenna not connected, all

channelsare skipped. Therefore, firmlyconnect the antenna and

then turn the VCR off and on againto execute Auto tuning.

2. When Auto Tuning iscanceled halfway, Auto Tuning isnot

executed even ifthe VCR isturned off and then turned on again. /

Inthiscase, Auto Tuning have to be restarted bythe following

procedure.

A. Press EJECTand remove the Video cassette.

B. Keep UPand DOWNon the VCR pressed simultaneouslyfor 3

seconds or more during the VCR on. / The channel displayed

on the VCR displaydisappears for amoment then changes to 2.

C. Turn off the VCR and then turn iton. Auto Tuning commences.

3. Ifyou turn the VCR off during Auto Tuning, Auto Tuning will stop

halfway.

The VCR shouldbe reset and restarted bythe item 2inorder to

execute Auto Tuning.

4. Ifthe VCR starts playback during Auto Tuning, Auto Tuning will

stop halfway.

The VCR shouldbe reset and restarted bythe item 2inorder to

execute Auto Tuning.

5. To cancel Auto Tuning Mid-operation, press POWERduring Auto

Tuning (The VCR isturned off).

6. When the VCR ismoved to the other area or country, TV

broadcasts shouldbe stored again.

2.1.3. CHECKING OFMAIN C.B.A.

Whenservicing the MAIN C.B.A., take out the MAIN C.B.A. and mechanismfromthe frame and

turnover.

And thenconnect the Extension Cable (VFK2744) betweenthe POWER C.B.A. connector(P1103)

and the MAIN C.B.A. connector(P1001) as shownin Fig. S3.

Fig. S3

2.1.4. REMOVALOFCASSETTE TAPE

There are 2 ways toremove a cassette tape.

1. Removal of compulsoryloading.

A. Press FF and EJECTbuttons simultaneouslyand set the

Service Mode 7.

B. Press STOPbutton inorder to unload the mechanism. (Payan

attention of tape slack)

Service Mode Indication:

7** ** (STOP) 700 ** (EJECT)

2. Removal of manual operation of Maincam gear.

A. Disconnect the AC power cord and remove Top Panel.

B. Rotate MainCam Gear to the clockwise and unload the

mechanism (Tape isremaining) (Fig. S4).

Fig. S4

C. Rotate the Poleof Capstan motor to the clockwise the from the

bottom inorder to remove the tape slag.

Fig. S5

D. Rotate MainCam Gear to the clockwise inorder to eject the

cassette tape.

2.1.5. CYLINDER UNITREPLACEMENT

1. CYLINDERUNITREPLACEMENT

A. Remove the Mechanism unitfrom MAINC.B.A./Chassisby

referring “SECTION2.DisassemblyProcedure”.

B. Remove the 3screws(A)of the CYLINDERUNITwith ascrew

driver.

C. Unlock the 4locking tabs (B)and disconnect the Cylinder

flexiblecard from the FPCHolder.

D. Remove the CYLINDERUNIT.

CAUTION

Handlethe Cylinder flexiblecard with care. When itdamaged, you

shouldreplace wholeCylinder unit.

Fig. S6

2. UPPERCYLINDERDISASSEMBLY

A. Remove 2screws(A).

B. Remove the Cylinder Stator Unit.

C. Remove 2screws(B).

D. Remove the Cylinder Rotor Unit.

E. Loose Hex screw (C)(1.5mm) and remove the CYLINDER

RETAINER.

F. Remove the Upper Cylinder. Fig. S7

3. UPPERCYLINDERASSEMBLY

When reassembling, perform the steps inthe reverse order.

Notes :

A. Install the Cylinder Retainer so that the 2holes on top of the

Cylinder Retainer are at right angles with the P3502 Connection.

B. Tighten the Hex screw (C)(1.5mm) whilepressing downon top

of the Cylinder Retainer. Fig. S8

C. Install the Cylinder Rotor Unitso that the inner holeof the

Cylinder Rotor Unitfits to the small projection (D)on top of the

Upper Cylinder.

D. Tighten 2screws(B). Fig. S9

E. Install the Cylinder Stator Unit.

F. Tighten 2screws(A). Fig. S10

G. Confirm the PG SHIFTERADJUSTMENTwith the alignment

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de VCR de Panasonic

Panasonic

Panasonic NV-HD650 Series Manual de usuario

Panasonic

Panasonic NV-HD70EA Manual de usuario

Panasonic

Panasonic Omnivision PV-V4611 Manual de usuario

Panasonic

Panasonic NV-HV60EB Manual de usuario

Panasonic

Panasonic NV-P05REE Manual de usuario

Panasonic

Panasonic AJ-HD130 Manual de usuario

Panasonic

Panasonic Omnivision PV-S4690 Manual de usuario

Panasonic

Panasonic NV-FJ730 Series Manual de usuario

Panasonic

Panasonic Omnivision PV-9668 Manual de usuario

Panasonic

Panasonic AG-DV2000P Manual de usuario

Panasonic

Panasonic PV-V4623S-K Manual de usuario

Panasonic

Panasonic Omnivision PV-C2023 Manual de usuario

Panasonic

Panasonic PV-V4622-K Manual de usuario

Panasonic

Panasonic NV-SD230 Manual de usuario

Panasonic

Panasonic NV-SD200BA Manual de usuario

Panasonic

Panasonic Omnivision PV-4666 Manual de usuario

Panasonic

Panasonic Omnivision PV-V4611 Manual de usuario

Panasonic

Panasonic NV-FJ620EG Manual de usuario

Panasonic

Panasonic Quasar Omnivision PV-V4021-K Manual de usuario

Panasonic

Panasonic Omnivision PV-7200 Manual de usuario

Panasonic

Panasonic AG-DTL1 Manual de usuario

Panasonic

Panasonic AG-6740P Manual de usuario

Panasonic

Panasonic AJ-HD150 Manual de usuario

Panasonic

Panasonic NV-FJ620 Manual de usuario

Manuales populares de Sistema de VCR de otras marcas

Toshiba

Toshiba M-662 Manual de usuario

Sony

Sony GV-500 Primary Manual de usuario

JVC

JVC HR-J282EU Manual de usuario

Sony

Sony HDCAM-SR SRW5800 Manual de usuario

Magnavox

Magnavox VRU242AT Manual de usuario

Sony

Sony HVR-M10C Manual de usuario

RCA

RCA VR634HF - Hi-Fi VCR Manual de usuario

JVC

JVC HR-5910U Manual de usuario

JVC

JVC HR-S8600EU Manual de usuario

JVC

JVC HR-FS1U Manual de usuario

Sharp

Sharp VC-H9888U Manual de usuario

FUNAI

FUNAI LC-950 Manual de usuario

Sharp

Sharp VC-S2000GM Manual de usuario

Sony

Sony Video8 EV-A60 Manual de usuario

Aiwa

Aiwa HV-E212 Manual de usuario

JVC

JVC HR-J3006UM Manual de usuario

GE VG4271 Manual de usuario

RCA

RCA VR678HF Manual de usuario