Panasonic TX-29P150T Manual de usuario
Power Source AC Auto 110-240 V, 50/60 Hz
Power Consumption 197 W
Standby condition : 11 W
Receiving System
Function
Reception of broadcast
transmissions and Playback
from Video Cassette Tape
Recorders
Playback from special VCRs
Playback from Special Disc
Players and Special VCRs
21 Systems
PAL B, G, H
PAL I
PAL D, K
SECAM B, G
SECAM D, K
SECAM K1
NTSC M (NTSC 3.58/4.5 MHz
NTSC 4.43/5.5 MHz
NTSC 4.43/6.0 MHz
NTSC 4.43/6.5 MHz
NTSC 3.58/5.5 MHz
NTSC 3.58/6.0 MHz
NTSC 3.58/6.5 MHz)
SECAM I
PAL 60 Hz/5.5 MHz
PAL 60 Hz/6.0 MHz
PAL 60 Hz/6.5 MHz
SECAM 60 Hz/5.5 MHz
SECAM 60 Hz/6.0 MHz
SECAM 60 Hz/6.5 MHz
NTSC 50 Hz/4.5 MHz
Receiving Channels Regular TV
© 2002 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
TX-29P150T
MD3 Chassis
VHF BAND
UHF BAND
CATV
2-12 (PAL/SECAM B, K1)
0-12 (PAL B AUST.)
1-9 (PAL B N.Z.)
1-12 (PAL/SECAM D)
1-12 (NTSC M Japan)
2-13 (NTSC M U.S.A.)
21-69 (PAL G,H,I/SECAM G,K,K1)
28-69(PALBAUST.)
13-57 (PAL D,K)
13-62 (NTSC M Japan)
14-69 (NTSC M U.S.A.)
S1-S20 (OSCAR)
1-125 (U.S.A. CATV)
C13-C49 (JAPAN)
S21-S41 (HYPER)
Z1-Z37 (CHINA)
5A, 9A (AUST.)
Receiving Stereo System NICAM I, NICAM B/G, NICAM D, A2
(German)
Tuning System Frequency synthesizer
Auto Search Tuning
POSITION : 100 Position
DIRECT : 125 Position
High Voltage 31.0 ± 1.0 kV at zero beam current
Picture Tube Overall Picture tube measured
diagonally : 73 cm
Viewable Picture tube measured
diagonally : 68 cm
CRT Deflection : 104°
Audio Output 8W x 2 (Speaker) 14W (Woofer)
Colour Television
Specifications
Order No. MTV0201145C3
Headphones 3.5 mm Plug
Aerial Impedance 75 ΩUnbalanced Coaxial
Video/Audio/Component
Terminals
AV 1, 2, 3, 4
DVD
Monitor Out
AV1 IN (Rear) : S-Video,
Video, Audio L/R terminals
AV2 IN (Front) : S-Video,
Video, Audio L/R RGB
Terminals
AV3 IN (Rear) : Video, Audio
L/R terminals
AV4 IN (Rear) : Video or
Y/PB/PR, Audio L/R terminals
S-Video In Y:1 Vp-p, 75 Ω
C:0:3 Vp-p 75 Ω
Y1.0Vp-p,75Ω
PB0.7Vp-p, 75Ω
PR0.7Vp-p, 75Ω
Video In 1 Vp-p, 75 Ω
Audio In Approx 0.4 V 47 kΩ
VideoOut1Vp-p,75Ω
Audio Out Approx. 0.4 V 1 kΩ
1 Safety Precautions 3
1.1. General Guide 3
1.2. Leakage Current Cold Check 3
1.3. Leakage Current Hot Check (See Fig. 1) 3
1.4. X-Radiation 4
2 SERVICE HINTS 5
2.1. HOW TO REMOVE THE REAR COVER 5
2.2. HOW TO MOVE THE CHASSIS INTO SERVICE
POSITION 5
2.3. HOTEL MODE 5
3 SELF CHECK 6
4 SERVICE MODE FUNCTION 7
4.1. HOW TO ENTER SERVICE 1 7
4.2. HOW TO ENTER SERVICE 2 7
5 ADJUSTMENT PROCEDURE 11
5.1. VOLTAGE CONFIRMATION 11
5.2. E.H.T CHECK 11
5.3. SUB CONTRAST 11
5.4. SUB TINT 12
5.5. SUB COLOUR 12
5.6. VRS ADJUSTMENT 13
5.7. COLOUR PURITY 14
5.8. CONVERGENCE 14
5.9. CUT OFF 15
5.10. WHITE BALANCE 16
5.11. FOCUS 16
RGB Input High-DENSITY D-sub 15 pin
31.5 kHz/60 Hz (640 x 480 dot) and
31.5kHz/70Hz(640x400dot)
Remote Control Transmitter R6 (AA) Battery x 2
75 Ωcoaxial aerial plug
Dimensions (W x D x H) 699 mm x 509 mm x 584 mm
Weight (Mass) 53 kg (Net)
Note:
Design and Specifications are subject to change without notice.
Weight and Dimensions shown are approximate.
5.12. GEOMAGNETIC 16
5.13. SUB BRIGHT 16
6 DEFLECTION ADJUSTMENT 17
6.1. V-ADJUSTMENT/CONFIRMATION (4:3 MODE) 17
6.2. H-DEFLECTION CONFIRMATION/ADJUSTMENT (4:3
MODE) 18
6.3. EW ADJUSTMENT/CONFIRMATION (4:3 MODE) 18
6.4. V LINIALITY ADJUSTMENT / CONFIRMATION (4:3
MODE) 20
6.5. DEFLECTION (16:9 MODE) ADJUSTMENT /
CONFIRMATION 21
6.6. 525p DEFLECTION ADJUSTMENT / CONFIRMATION
21
6.7. 625p DEFLECTION ADJUSTMENT 22
6.8. VGA480 / 60 Hz DEFLECTION ADJUSTMENT /
CONFIRMATION 22
6.9. VGA400 / 70 Hz DEFLECTION ADJUSTMENT /
CONFIRMATION 23
6.10. TABLE 1 23
7 CONDUCTOR VIEWS 25
7.1. A-Board 25
8 SCHEMATIC DIAGRAMS 27
8.1. SCHEMATIC DIAGRAM NOTES 27
9 PARTS LOCATION 37
10 Replacement Parts List 39
10.1. Replacement Parts List Notes 39
10.2. Replacement Part List 40
CONTENTS
Page Page
2
TX-29P150T
1 Safety Precautions
1.1. General Guide
1. It is advisable to insert an isolation transformer in the AC
supply before servicing a hot chassis.
2. When servicing, observe the original lead dress, especially
the lead dress in the high voltage circuits. If a short circuit is
found, replace all parts which have been overheated or
damaged by the short circuit.
3. After servicing, see to it that all the protective devices such
as insulation barriers, insulation papers, shields and
isolation R-C combinations, are properly installed.
4. When the receiver is not to be used for a long period of
time, unplug the power cord from the AC outlet.
5. Potential, as high as 32.0 kV is present when this receiver
is in operation. Operation of the receiver without the rear
cover involves the danger of a shock hazard from the
receiver power supply. Servicing should not be attempted
by anyone who is not thoroughly familiar with the
precautions necessary when working on high voltage
equipment. Always discharge the anode of the picture tube
to the receiver chassis before handling the tube.
6. After servicing make the following leakage current checks to
prevent the customer from being exposed to shock
hazards.
1.2. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two
prongs on the plug.
2. Turn on the receiver’s power switch.
3. Measure the resistance value, with an ohmmeter, between
the jumper AC plug and each exposed metallic cabinet part
on the receiver, such as screw heads, aerials, connectors,
control shafts, etc. When the exposed metallic part has a
return path to the chassis, the reading should be between 4
MΩ
ΩΩ
Ωand 20 MΩ
ΩΩ
Ω. When the exposed metal does not have a
return path to the chassis, the reading must be infinite.
1.3. Leakage Current Hot Check
(See Fig. 1)
1. Plug the AC cord directly into the AC outlet. Do not use an
isolation transformer for this check.
2. Connect a 2kΩ, 10 W resistor in series with an exposed
metallic part on the receiver and an earth such as a water
pipe.
3. Use an AC voltmeter, with high impedance type, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the
voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the
above measurements.
6. The potential any point should not exceed 1.0 V rms. In the
case of a measurement being outside of the limits specified,
there is a possibility of a shock hazard, and the receiver
should be repaired and rechecked before it is returned to
the customer.
3
TX-29P150T
1.4. X-Radiation
Warning :
1. The potential sources of X-Radiation in TV sets are the EHT
section and the picture tube.
2. When using a picture tube test rig for service, ensure that
the rig is capable of handling 32.0 kV without causing X-
Radiation.
Note: It is important to use an accurate periodically calibrated
high voltage meter.
1. Set the brightness to minimum.
2. Measure the High Voltage. The meter reading should
indicate 31.0 ± 1 kV. If the meter indication is out of
tolerance, immediate service and correction is required to
prevent the possibility of premature component failure.
3. To prevent the possibility of X-Radiation, it is essential to
use the specified picture tube.
4
TX-29P150T
2 SERVICE HINTS
2.1. HOW TO REMOVE THE REAR
COVER
1. Remove the 9 screws as shown in Fig. 1.
Fig. 1
2.2. HOW TO MOVE THE CHASSIS
INTO SERVICE POSITION
1. Hold and lift the rear of the chassis and gently pull the
chassis towards you as shown in Fig. 3.
2. Release the respective wiring clips and rotate the chassis
vertically through 90° anticlockwise.
3. After servicing replace the bead clamper and ensure all
wiring is returned to its original position before returning the
receiver to the customer.
2.3. HOTEL MODE
Purpose
1. At Hotels, this Mode prevents the customer from changing
the TV preset data such as Channel preset data.
Note: This Mode is useful for Hotels. You should not get
into “Hotel mode” with Normal use.
Operation
1. To get into “Hotel Mode”, press the remote control “Recall”
button and Channel up “[+/ ]” key on the TV set
simultaneously, after setting the “Off-Timer” mode.
2. In this mode, the Channel up and down Function will be
enabled as normal and the maximum volume level for this
mode is set at the current volume level, i.e. the setting at
the level before entering the mode. However, other
functions will be disabled.
3.
To exit this mode, exit “Off-Timer” mode and the “Volume
Down [-/ ]” key simultaneously.
* This information is informed by Service Manual only.
5
TX-29P150T
3 SELF CHECK
1. Self-Check is used to automatically check the bus lines and hexadecimal code of the TV set.
2. To get into the Self-Check mode, press the down n [-/ ] button on the customer controls at the front of the set, at the same
time pressing the HELP button on the remote control and the screen will show:
If the CCU ports have been checked and found to be incorrect or not located then “--” will appear in place of “O.K.”.
6
TX-29P150T
4 SERVICE MODE FUNCTION
MPU controls the functions switching for each IIC through IIC bus in this chassis. The following setting and adjustment can be
adjusted by remote control in Service Mode.
4.1. HOW TO ENTER SERVICE 1
1. In sound menu, set BASS to MAX and set TREBLE to MINIMUM.
2. Simultaneously press INDEX button on remote control and VOLUME DOWN button [ - ] on the TV set.
4.2. HOW TO ENTER SERVICE 2
1. Set the channel to CH99.
2. Press HOLD button on remote control.
Note:
To exit Service mode, press N or Power button on remote control.
7
TX-29P150T
Options
Model
Description
option1 00
0E0 b0 1 Colour system (TV) PAL(1)
b1 1 SECAM(1)
b2 1 NTSC(1)
b3 1 M.NTSC(1)
b4 0 Colour system (AV) PAL(1)
b5 0 SECAM(1)
b6 1 NTSC(1)
b7 1 M.NTSC(1)
option2 00
0E1 b0 1 CH Plan ASIA/M.E/HK/UK/CHINA(1)
b1 1 NZ/INDNES(1)
b2 1 AUSTRALIA(1)
b3 1 E.EUROPE(1)
b4 1 SPECIAL(1)
b5 1 AMERICA(1)
b6 1 CATV(1)
b7 1 JAPAN(1)
option3 00
0E2 b0 1 A2 enable 4.5(1)
b1 1 5.5(1)
b2 1 6.0(1)
b3 1 NICAM enable 6.5(1)
b4 0 4.5(1)
b5 0 5.5(1)
b6 0 6.0(1)
b7 0 6.5(1)
option4 00
0E3 b0 0 A2 select 6.5MHz 5.742MHz(0) 6.742MHz(1)
b1 1 NICAM priority ASIA/M.E.(1)
b2 0 HK/UK(1)
b3 0 CHINA(1)
b4 0 NZ/INDONESIA(1)
b5 1 AUSTRALIA(1)
b6 1 E.EUROPE(1)
b7 1 SPECIAL(1)
option5 00
0E4 b0 0 Virtual Dolby Surround enable(1)
b1 1 NICAM C4 bit enable(1)
b2 1 Noise mute Noise mute enable(1)
b3 1 Monitor out AV1 mute Monitor out AV1 mute(1)
b4 1 SIF 4.5(1)
b5 1 5.5(1)
b6 1 6.0(1)
b7 1 6.5(1)
8
TX-29P150T
Options
Model
Description
option6 00
0E5 b0 1 Reserved Geomagnetic Enable (1)
b1 0 Geomagnetic Sensor Geomagnetic sensor enable (1)
b2 0 Geomagnetic Polarity Geomagnetic polarity Plus+(0), Minus-(1)
b3 0 P.NR. Enable(1)
b4 1 SASO enable SASO enable(1)
b5 0 Search speed Slow(1) Fast(0)
b6 1 VCR/GAME in search On(0) Off(1)
b7 0 Tuner MACO tuner (0), ALPS tuner (1)
option7 00
0E6 b0 0 TEXT enable(1)
b1 1 TEXT TOP TOP enable (1)
b2 1 TEXT language English(1)
b3 1 Cyrillic(1)
b4 1 E.Europe 1(1)
b5 0 E.Europe 2(1)
b6 1 Arabic(1)
b7 0
option8 00
0E7 b0 1 VGA enable(1)
b1 1 Reserved 1080i Enable(1)
b2 0 Reserved ID-1 Enable(1)
b3 0 Australia enable(1)
b4 1 OSD language ARABIC(1)
b5 0 RUSSIAN(1)
b6 1 CHINESE(1)
b7 0 free
option9 00
0E8 b0 1 Panasonic LOGO Display(1)
b1 1 MPX status Display(1)
b2 0 Scan mode AUTO for P-NTSC Progressive2(0), Progressive(1)
b3 0 free
b4 0 free
b5 0 free
b6 1 X-ray protection Enable(1)
b7 1 5V detect protection Enable(1)
option10 00
0E9 b0 1 free enable(1)
b1 1 OSD language enable(1)
b2 1 Noise mute enable(1)
b3 1 Monitor out AV1 mute(1)
b4 1 free 4.5(1)
b5 1 free 5.5(1)
b6 1 free 6.0(1)
b7 1 Protect 5V detect 6.5(1)
9
TX-29P150T
Options
Model
Description
option11 4E
0EA b0 0 Shop mode enable(1)
b1 1 Full/16.9 display Reserved
b2 1 Sub Headphone enable(1)
b3 1 Scan mode Blanking Blanking enable(1)
b4 0 User aspect 14:9 enable(1)
b5 0 NICAM C4 bit enable(1)
b6 1 ID-1 enable(1)
b7 0 1080i enable(1)
option12 41
0EB b0 1 Asia Asia(1), Europe(0)
b1 0
b2 0 Ireland not use
b3 0 UK not use
b4 0
b5 0 (Reserved for 29 inch etc)
b6 1 Large size 52(1) / 42(0) for PTV, 36(1) / 32(0) for wide, 34(1) / 29(0) for 4:3
b7 0 PTV PTV (1)
option13 7A Temporary
0EC b0 0 VDU Version A21 (0), A12 (1)
b1 1 GC Version ES5(0), ES6(1)
b2 0 UV Swap Swap(1)
b3 1 TEXT Enable(1)
b4 1 Main GC ES7 ES7(1), ES5/6(0)
b5 1 Sub GC ES7v ES7(1), ES5/6(0)
b6 1
b7 0 CIP2 without CIP1(0), with CIP1(1)
10
TX-29P150T
Tabla de contenidos
Otros manuales de TELEVISOR de Panasonic
Panasonic
Panasonic TX58DX800E Instrucciones de montaje
Panasonic
Panasonic CT-32SL32 Manual de usuario
Panasonic
Panasonic CT-G2973 Manual de usuario
Panasonic
Panasonic VIERA TX-40CX700E Manual de usuario
Panasonic
Panasonic TX-28DK2 Manual de usuario
Panasonic
Panasonic TX-25SL1FZ Manual de usuario
Panasonic
Panasonic TC-60AS530U Instrucciones de montaje
Panasonic
Panasonic TX-28SLB1F Manual de usuario
Panasonic
Panasonic TX-W28R3F Manual de usuario
Panasonic
Panasonic VIERA TX-P42S10B Manual de usuario
Panasonic
Panasonic TX-32F250A Manual de usuario
Panasonic
Panasonic TX-W32D2DP Manual de usuario
Panasonic
Panasonic TX-28DK1L Manual de usuario
Panasonic
Panasonic CT-F2936LC Manual de usuario
Panasonic
Panasonic QuintrixF TX-21AP2 Manual de usuario
Panasonic
Panasonic TX-21FG50M-SINGAPORE Manual de usuario
Panasonic
Panasonic TX-28F250A-AUSTRALIA Manual de usuario
Panasonic
Panasonic CT-36G24 Manual de usuario
Panasonic
Panasonic CT-32E14 Manual de usuario
Panasonic
Panasonic TX-32DS600E Instrucciones de montaje
Manuales populares de TELEVISOR de otras marcas
Philips
Philips Colour Television Manual de usuario
Toshiba
Toshiba 27A10 Manual de usuario
Philips
Philips 42PF9630A/37 Manual de usuario
Hitachi
Hitachi 32FX48B Manual de usuario
DAEWOO ELECTRONICS
DAEWOO ELECTRONICS DTQ-14V1FC Manual de usuario
Changhong Electric
Changhong Electric uhd55b6000is Manual de usuario
