Panasonic PVDM2092 - MONITOR/DVD COMBO Manual de usuario

ORDERNO. MKE0207607C1

B22

TV/DVD/VCR Combination

PV-DM2092 / PV-DM2092-K

SPECIFICATIONS

2002 Matsushita Kotobuki Electronics Industries LTD. All rights

reserved. Unauthorized copying and distribution isaviolation of

law.

1. SAFETY PRECAUTIONS

1.1. GENERALGUIDELINES

1. IMPORTANTSAFETY NOTICE

There are special components used inthisequipment which are

important for safety. These parts are marked byinthe

SchematicDiagrams, CircuitBoard Layout, Exploded Viewsand

Replacement Parts List. Itisessential thatthese critical parts

shouldbe replaced with manufacturer’sspecified parts to prevent

X-RADIATION, shock, fire, or other hazards. Donot modifythe

original design without permission of manufacturer.

2. AnIsolation Transformer shouldalwaysbe used during the

servicing of Combination DVDVCR whose chassisisnot isolated

from the AC power line. Use atransformer of adequate power

rating as thisprotects the technician from accidents resultingin

personal injuryfrom electrical shocks. Itwill also protect

Combination DVDVCR from being damaged byaccidental

shorting that mayoccur during servicing.

3. When servicing, observe the original lead dress, especiallythe

lead dress inthe high voltage circuits. Ifashort circuitisfound,

replace all parts which have been overheated or damaged bythe

short circuit.

4. After servicing, see to itthat all the protective devices such as

insulation barriers, insulation papers, shield, and isolation R-C

combinations are properlyinstalled.

5. Before turning the receiver on, measure the resistance between B+

line and chassisground. Connect (-) side of an ohmmeter to the B

+ lines, and (+)side to chassisground. Each line shouldhave

more resistance than specified,as follows:

B+ Line

Minimum Resistance

130 V

1k (Coldchassisground)

27 V

180 (Coldchassisground)

210 V

1k (Coldchassisground)

6. When the TV set isnot used for along period of time, unplug the

power cord from the AC outlet.

7. Potentials, as high as 30.0kV are present when thisTV set isin

operation. Operation of the TV set without the rear cover involves

the danger of ashock hazard from the TV set power supply.

Servicing shouldnot be attempted byanyone who isnot

thoroughlyfamiliar with the precautions necessarywhen working

on high voltage equipment. Alwaysdischarge the anode of the

picture tube to the CRTground of receiver before handling the

tube.

8. After servicing make the following leakage current checks to

prevent the customer from being exposed to shock hazards.

1.2. LEAKAGECURRENTCOLDCHECK

1. Unplug the AC cord and connect ajumper between the two

prongs on the plug.

2. For physicallyoperated power switches, turn power on. Otherwise

skipstep 2.

3. Measure the resistance value, with an ohmmeter, between the

jumpered AC plug and each exposed metalliccabinet part on the

receiver, such as screwheads, connectors, etc. When the exposed

metallicpart has areturn path to the chassis, the readingshould

be between 1M and 12 M . When the exposed metal does not

have areturn path to the chassis, the reading must be infinity.

1.3. LEAKAGECURRENTHOTCHECK

1. Plug the AC cord directlyinto the AC outlet.

Donot use aisolation transformer for thischeck.

2. Connect a1.5k , 10 Wresistor, inparallel with a0.15 F

capacitor, between each exposed metallicpart on the set and a

good earth ground, as showninFigure 1.

3. Use an AC voltmeter, with 1k /Vor more sensitivity, to measure

the potential across the resistor.

4. Check each exposed metallicpart, and measure the voltage at

each point.

5. Reverse the AC plug inthe AC outlet and repeat each of the above

measurements.

6. The potential at anypoint shouldnot exceed 0.75 VRMS.

Aleakage current tester (Simpson Model 229 equivalent) maybe

used to make the hot checks. Leakage current must not exceed 1/

2mA. Incase ameasurement isoutside of the limits specified,

there isapossibilityof shock hazard, and thereceiver shouldbe

repaired and rechecked before itisreturned to the customer.

Figure 1

2. X-RADIATION

WARNING :

1. The potential source of X-Radiation inTV sets isthe High Voltage

section and the picture tube.

2. When using apicture tube test fixture for service, ensure that the

fixture iscapableof handling 34.5kV without causing X-Radiation.

NOTE:

Itisimportant to use an accurate periodicallycalibrated high

voltage meter.

1. Reduce the brightness to minimum.

2. Set the SERVICEswitch to SERVICE.

3. Measure the High Voltage. The meter reading shouldindicate 28.5

kV±1.5kV.

Ifthe meter indication isout of tolerance, immediate service and

correction isrequired to prevent the possibilityof premature

component failure.

4. To prevent an X-Radiation possibly, itisessential to use the

specified picture tube.

2.1. HORIZONTALOSCILLATORDISABLE CIRCUITTEST

SERVICE WARNING :

The test must be made as a final check before set is returnedtothe customer.

1. With the rear cover removed, supplyabout a120 VAC power

source to the set, turn on the set.

2. Set the customer controlsto normal operating positions.

3. Short between TP891 and TP892 on the Maincircuitboard with a

jumper wire. Confirm that the picture goes out of horizontal sync.

4. Ifthisdoes not occur, the horizontal oscillator disablecircuitis

not operating. Follow the RepairProcedures of horizontal

oscillator disablecircuitbefore the set isreturned to customer.

2.2. REPAIRPROCEDURES OFHORIZONTALOSCILLATOR

DISABLE CIRCUIT

1. Connect aDC voltmeter between capacitor C513 (+)on the Main

circuitboard and chassisground.

2. Ifapproximately+21.5Visnot present at that point when 120 V

AC isapplied, find the cause. Check R503, R5505, C5507, C513

and D503.

3. Carefullycheck above specified parts and related circuits and

parts. When the circuitisrepaired, trythe horizontal oscillator

disablecircuittest again.

2.3. CIRCUITEXPLANATION

2.3.1. HORIZONTALOSCILLATOR DISABLE CIRCUIT

The positive DC voltage, suppliedfromthe D503 cathode formonitoring high voltage, is applied

tothe IC5301 Pin11 through R503 and R5504. Undernormal conditions, the voltage at IC5301

Pin11 is less thanapprox. 3 V. If the high voltage at FlybackTransformerPin5 exceeds the

specifiedvoltage, the positive DC voltage whichis suppliedfromthe D503 cathode also

increases. The increasedvoltage is appliedtoIC5301 Pin11 through R503 and R5504. Due tothe

increasedvoltage at IC5301 Pin11,the horizontal oscillatorfrequencyincreases, the picture goes

out of horizontal sync, the beamcurrent decreases and the picture become dark inorderto

keepX-radiation underspecification.

Figure 2

2.4. LASERPRODUCT

CLASS I LASER PRODUCT

-Thisequipment iscertified to complywith DHHSRules 21 CFR

Chapter 1, Subchapter Jineffect as of date of manufacture. (Only

for U.S.A.)

This equipment is classifiedas a Class I (Class 1) level LASER Product and there is no

hazardous LASER radiation withthe safetyprotection.

Caution:

Use of controlsor adjustments or performance of procedures other

than those specified hereinmayresultinhazardous radiation

exposure.

Nevertouchthe internal parts inordertoavoidEXPOSURE TO VISIBLE LASER RADIATION.

Unplug the AC powercordtothe equipment whenopening the top cover.

Whenthe powerswitchis On, do not place youreyes close tothe front panel opening dooror

the otheropenings tolook intothe interiorunit.

LASER Specification

Class I level A LASER Product (Class 1 level A LASER Product)

Wave Length:

647 -677 nm (at DVD)

775 -815 nm (at CD)

Laser Power:

Nohazardous radiation isemitted with the safetyprotection.

2.5. PRECAUTIONOFLASERDIODE

CAUTION:

Thisunitutilizes aclass III alaser. Visiblelaser radiation isemitted

from the optical pickup lens when the unitisturned on:

1. Donot look directlyinto the pickup lens.

2. Donot use optical instruments to look at the pickup lens.

3. Donot adjust the preset variableresistor on the optical pickup.

4. Donot disassemblethe optical pickup unit.

5. Ifthe optical pickup isreplaced, use the manufactures specified

replacement pickup only.

6. Use of control or adjustment or performance of procedures other

than those specified hereinmayresultinhazardous radiation

exposure.

3. PREVENTION OF ELECTROSTATIC DISCHARGE

(ESD) TO ELECTROSTATICALLY SENSITIVE (ES)

DEVICES

Some semiconductor(solidstate) devices canbe damagedeasilybystatic electricity. Such

components commonlyare calledElectrostaticallySensitive (ES) Devices. Examples of typical

ES devices are integratedcircuits and some field-effect transistorsare semiconductor"chip"

components. The following techniques shouldbe usedtohelpreduce the incidence of

component damage causedbyelectrostatic discharge (ESD).

1. Immediatelybefore handling anysemiconductor component or

semiconductor-equipped assembly, drainoff anyESDon your

bodytouching aknownearth ground. Alternatively, obtainand

wear acommerciallyavailabledischarging ESDwrist strap,

whichshouldbe removed for potential shock reasons prior to

applying power to the unitunder test.

2. After removing an electrical assemblyequipped with ES devices,

place the assemblyon aconductive surface such as aluminum

foil, to prevent electrostaticcharge buildup or exposure of the

assembly.

3. Use onlyagrounded-tipsoldering iron to solder or unsolder ES

devices.

4. Use onlyan anti-staticsolder removal device. Some solder

removal devices not classified as "anti-static(ESDprotected)"

can generate electrical charge sufficient to damage ES devices.

5. Donot use freon-propelled chemicals. These can generate

electrical charges sufficient to damage ES devices.

6. Donot remove areplacement ES device from its protective

package until immediatelybefore you are readyto install it. (Most

replacement ES devices are packaged with leads electrically

shorted together byconductive foam, aluminum foil or

comparableconductive material).

7. Immediatelybefore removing the protective material from the

leads of areplacement ES device, touch the protective material to

the chassisor circuitassemblyinto which the device will be

installed.

CAUTION:

Besure no power isapplied to the chassisor circuit, and observe

all other safetyprecautions.

8. Minimize bodilymotions when handling unpackaged replacement

ES devices. (Otherwise harmless motion such as the brushing

together of your clothes fabricor the lifting of your foot from a

carpeted floor can generate staticelectricity(ESD)sufficient to

damage an ES device).

"NOTE toCATV systeminstaller:

Thisreminder isprovided to call the CATV system installer’s

attention to Article820-40 of the NECthat provides guidelines for

proper grounding and, inparticular, specifies that the cableground

shall be connected to the grounding systemof the building, as

close to the point of cableentryas practical."

4. OPERATION GUIDE

5. SERVICE NOTES (PLEASE READ)

5.1. SERVICENOTES

5.1.1. SIMPLIFIED FAULT FINDING DATA

SimplifiedSelf-Diagnostic Systemfacilitates finding the cause of the fault. A 4 digit fault code

and communication forI2C bus code will be displayedon TV screen.

The SimplifiedFault finding data is storedinthe MemoryIC (IC6004). This data is clearedafterit

is displayed, and thenthe POWER button is pressedback on.

1. With power turned off, press FF and REW buttons on unit

together for over 3seconds. Fig. 1-1

2. TV power comes on and the unitgoes into service mode.

4digitfor faultcode and communication for I2Cbus code will be

displayed. Fig. 1-2

Fig. 1-3

Fig. 1-4

Fig. 1-5

Otros manuales para PVDM2092 - MONITOR/DVD COMBO

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de TELEVISOR de Panasonic

Panasonic

Panasonic CT27D10B - 27" COLOR TV Manual de usuario

Panasonic

Panasonic CT-36D32 Manual de usuario

Panasonic

Panasonic TX-34P800R Manual de usuario

Panasonic

Panasonic TX-P42VT30Y Manual de usuario

Panasonic

Panasonic TX-76PW05A Manual de usuario

Panasonic

Panasonic TX-W32D4DP Manual de usuario

Panasonic

Panasonic TX-21JT2P Manual de usuario

Panasonic

Panasonic TX-25V70T Manual de usuario

Panasonic

Panasonic TX-21AD2F Manual de usuario

Panasonic

Panasonic AG527DVDE - DVD/VCR/MONITOR Manual de usuario

Panasonic

Panasonic CT-36G23 Manual de usuario

Panasonic

Panasonic CT-35G21 Manual de usuario

Panasonic

Panasonic TH-50PF20U Manual de usuario

Panasonic

Panasonic QuintrixF TX-28PS10D Manual de usuario

Panasonic

Panasonic TX-L32E5E Manual de usuario

Panasonic

Panasonic TX-W28R4 Manual de usuario

Panasonic

Panasonic TX-29AK1F Manual de usuario

Panasonic

Panasonic TX-28LD4DPL Manual de usuario

Panasonic

Panasonic CT-Z2146L Manual de usuario

Panasonic

Panasonic CT-25L8 Manual de usuario

Panasonic

Panasonic TX-W28R4F Manual de usuario

Panasonic

Panasonic TX-28MK1F Manual de usuario

Panasonic

Panasonic TX-55CW324 Manual de usuario

Panasonic

Panasonic TX-W32R4F Manual de usuario

Manuales populares de TELEVISOR de otras marcas

Philips

Philips Colour Television Manual de usuario

Toshiba

Toshiba 27A10 Manual de usuario

Philips

Philips 42PF9630A/37 Manual de usuario

Hitachi

Hitachi 32FX48B Manual de usuario

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Manual de usuario

Changhong Electric

Changhong Electric uhd55b6000is Manual de usuario

Philips

Philips Matchline 21CE7551 Manual de usuario

Toshiba

Toshiba 19A20 Manual de usuario

Philips

Philips 25PT4523-16 Manual de usuario

Sony

Sony XBR-100Z9D Manual de usuario

Philips

Philips PR0930X3 Manual de usuario

Philips

Philips Brilliance 231P4QPY Manual de usuario

Samsung

Samsung 55S9 B Series Manual de usuario

Philips

Philips 32HF9385D Guía de solución de problemas

Sharp

Sharp LC-40FI5012E Manual de usuario

Loewe

Loewe Table Stand Reference 55 Manual de usuario

Philips

Philips 32PFH5300 Manual de usuario

Sylvania

Sylvania 6427FB Manual de usuario