Panasonic SB-WA340 Manual de usuario

ORDERNO. MD0310441C2

ActiveSubwooferSystem

SB-WA340EBS1

Colour

(S1)...SilverType

SPECIFICATIONS

Specification

Activesubwoofer

Type 1way, 1speakersystem, bass-

ref.

Woofer 17 cm conetype

Impedance 4

Outputsound pressurelevel 80 dB/W (1.0m)

Frequencyrange 40 Hz-220 Hz(-16 dB)

45 Hz-180 Hz(-10 dB)

Dimensions(W xHxD) 160 x450 x424 mm

Mass Approx. 12 kg

General

Powersupply AC230-240 V, 50 Hz

Powerconsumption 250 W

Powerconsumption in standby

mode 0.7W

Note:

Specificationsaresubjectto changewithoutnotice.

Mass and dimensionsareapproximate.

System :SC-HT1000EBS MusicCenter:SA-HT1000EBS

Frontspeakers:SB-PF1000P-S (x2)

Centerspeaker:SB-PC1000P-S (x1)

Surround speakers:SB-PS1000P-S (x2)

ActiveSubwoofer:SB-WA340EBS1

System :SC-HT1000EGS MusicCenter:SA-HT1000EGS

Frontspeakers:SB-PF1000P-S (x2)

Centerspeaker:SB-PC1000P-S (x1)

Surround speakers:SB-PS1000P-S (x2)

ActiveSubwoofer:SB-WA340EBS1

1. SafetyPrecautions

1.1. GENERALGUIDELINES

1. Whenservicing, observetheoriginal leaddress. Ifashortcircuit

isfound, replace all parts whichhavebeenoverheatedor

damagedbytheshortcircuit.

2. Afterservicing, see toitthat all theprotectivedevices suchas

insulation barriers, insulation papersshieldsareproperlyinstalled.

3. Afterservicing, make thefollowing leakagecurrentchecks to

preventthecustomerfrombeing exposedtoshock hazards.

1.1.1. LEAKAGE CURRENTCOLDCHECK

1. Unplug theACcordand connect ajumperbetweenthetwoprongs

on theplug.

2. Measuretheresistance value, withanohmmeter, betweenthe

jumperedACplug and eachexposedmetalliccabinet parton the

equipmentsuchas screwheads, connectors, control shafts, etc.

Whentheexposedmetallicparthas areturnpathtothechassis,

thereading shouldbebetween1M and 5.2 . / Whenthe

exposedmetal does nothaveareturnpathtothechassis, the

reading must be . Fig. 1

1.1.2. LEAKAGE CURRENTHOTCHECK (See Figure1.)

1. Plug theACcorddirectlyintotheACoutlet. Donotuse an

isolation transformerforthischeck.

2. Connect a1.5k , 10 watts resistor, inparallel witha0.15 F

capacitors, betweeneachexposedmetallicparton theset and a

good earthground suchas awaterpipe, as showninFigure1.

3. Use anACvoltmeter, with1000 ohms/voltormoresensitivity, to

measurethepotential across theresistor.

4. Check eachexposedmetallicpart, and measurethevoltageat

eachpoint.

5. Reverse theACplug intheACoutlet and repeat eachoftheabove

measurements.

6. Thepotential at anypointshouldnotexceed0.75 volts RMS. A

leakagecurrenttester(Simpson Model 229 orequivalent) maybe

usedtomake thehotchecks, leakagecurrentmust notexceed1/2

milliamp. Incase ameasurementisoutsideofthelimits specified,

thereisapossibilityofashock hazard, and theequipmentshould

berepairedand recheckedbeforeitisreturnedtothecustomer.

2. Handling the Lead-free Solder

2.1. Aboutleadfree solder(PbF)

Distinction ofPbF P.C.B. :

P.C.B.s(manufactured)using leadfree solderwill have aPbF stampon theP.C.B.

Caution:

-Pbfree solderhas ahighermelting pointthat standardsolder;

Typicallythemelting pointis50 -70°F(30 -40°C)higher. / Please

use ahigh temperaturesoldering iron. Incase ofthesoldering iron

withtemperaturecontrol, please set itto700 ±20°F(370 ±10°C).

-Pbfree solderwill tend tosplashwhenheatedtoo high (about

1100°F/600°C).

-Whensoldering orunsoldering, please completelyremoveall ofthe

solderon thepinsorsolderarea, and besuretoheat thesoldering

points withthePbfree solderuntil itmelts enough.

3. BeforeRepairand Adjustment

DisconnectACpower, dischargePowerSupplyCapacitorsC546, C547, C548, C549 through a10

, 1Wresistor toground.

DONOTSHORT-CIRCUITDIRECTLY(withascrewdriverblade, for instance), as thismay destroy

solidstatedevices.

Afterrepairsarecompleted, restorepowergraduallyusing avariac, toavoidovercurrent.

Currentconsumption atAC230-240V, 50HzinNOSIGNALmodeshouldbe~500 mA.

4. Protection Circuitry

Theprotection circuitrymay have operatedifeitherofthefollowing conditionsarenoticed:

-Nosound isheardwhenthepoweristurnedon.

-Sound stopsduring aperformance.

Thefunction ofthiscircuitryistopreventcircuitrydamageif, for example, thepositive and

negative speakerconnection wires are

“shorted”, or ifspeakersystemswithanimpedance less thantheindicatedratedimpedance of

theamplifierareused.

Ifthisoccurs, followtheprocedureoutlines below:

1. Turnoff thepower.

2. Determinethecause oftheproblemand correct it.

3. Turnon thepoweronce againafteroneminute.

Note:

Whentheprotection circuitryfunctions, theunitwill notoperateunless thepowerisfirstturned

off and thenon again.

5. Connection of the SpeakerCables

-Besuretoconnect speakercables beforeconnecting theACpower

supplycord.

-Theloadimpedance ofanyspeakerusedwiththisunitmust be4 .

-Besuretoconnect thecablefromtherightspeakertotheright

terminal and thecablefromtheleft speakertotheleft terminal.

1. Stripoff theoutercovering, and twist thecenterconductor. Make

surethebareendsofthewires arenotunravelled. (Iftheyare,

twist themtightagain.)

2. Insertthewiretotherearpanel oftheunitand close thelever.

Notes :

-To preventdamagetocircuitry, nevershort-circuitpositive(+)and

negative(-) speakerwires.

-Besuretoconnect onlypositive(red)wires topositive(+)terminals

and negative(black) wires tonegative(-) terminals.

6. DisassemblyProcedure

“ATTENTIONSERVICER”

Somechassiscomponentsmay have sharp edges.

Becareful whendisassembling and servicing.

1. Thissection describes procedures forchecking theoperation of

themajorprintedcircuitboardsand replacing themain

components.

2. Forreassemblyafteroperation checks orreplacement, reverse the

respectiveprocedures.

Special reassemblyprocedures aredescribedonlywhenrequired.

3. Select itemsfromthefollowing index whenchecks orreplacement

arerequired.

Contents

-DisassemblyoftheSpeakerUnit

-MainComponentReplacementProcedures

6.1. DisassemblyoftheSpeakerUnit

Step1:Remove 2screwsfrom therearpanel.

Step2:Remove all screws.

Step3:Remove theStand Base.

Step4:Remove all screwsfrom thespeakerbottom.

Step5:Pull thePower/AmpUnitas shown.

Step6:Release theconnector CN506 and pull outthePower/AmpUnit.

Step7:PushtheNetFramefrom twoholes insidetheunit.

Step8:Remove theNetFrame.

Step9:Remove all thescrews.

Step10:Remove theSpeaker.

Step11 &12:Remove all thescrews.

Step13:Release theconnector CN507.

Step14:Remove the2screws.

Step15 &16:Remove all thescrews.

Step17:Place thePowerPCB as shownfor checking.

Checking for ACInletPCB.

6.2. MainComponentReplacementProcedures

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Subwoofer de Panasonic

Panasonic

Panasonic SB-WA520GC Manual de usuario

Panasonic

Panasonic Ramsa WS-A240 Manual de usuario

Panasonic

Panasonic SB-WA730GCP Manual de usuario

Panasonic

Panasonic SB-W40P Manual de usuario

Panasonic

Panasonic SB-AS35 Manual de usuario

Panasonic

Panasonic SB-WA535EE Manual de usuario

Panasonic

Panasonic SB-WA17E Manual de usuario

Panasonic

Panasonic SB-WA730GCP Manual de usuario

Panasonic

Panasonic SB-WA730 Manual de usuario

Panasonic

Panasonic SB-WA500PP Manual de usuario

Panasonic

Panasonic SB-WA330GCS Manual de usuario

Panasonic

Panasonic SB-WA100 Manual de usuario

Panasonic

Panasonic SB-W340E Manual de usuario

Panasonic

Panasonic SB-WA530EB Manual de usuario

Panasonic

Panasonic SB-WA520EB Manual de usuario

Panasonic

Panasonic SBW500 - SUBWOOFER SYS Manual de usuario

Panasonic

Panasonic SB-WA100K Manual de usuario

Panasonic

Panasonic Ramsa WS-A240 Manual de usuario

Panasonic

Panasonic SB-WA530EB Manual de usuario

Panasonic

Panasonic Ramsa WS-A240 Manual de usuario

Panasonic

Panasonic SB-AS35 Manual de usuario

Panasonic

Panasonic SB-WA05E Manual de usuario

Panasonic

Panasonic SB-WA730PP Manual de usuario

Panasonic

Panasonic SBW500 - SUBWOOFER SYS Manual de usuario

Manuales populares de Subwoofer de otras marcas

Sony

Sony XS-AW8 Manual de usuario

Sony

Sony XS-L836 Manual de usuario

B&C Speakers

B&C Speakers 15 HPL 76W Manual de usuario

Velodyne

Velodyne DD-18+ Manual de usuario

Sonance

Sonance Cinema Series SUB 10-150 Manual de usuario

Hifonics

Hifonics HW-12 Guía de inicio rápido

Magnat Audio

Magnat Audio ADR 130 BP Manual de usuario

Blitz

Blitz BZP106 Manual de usuario

Technics

Technics SB-AS500 Manual de usuario

Lyngdorf

Lyngdorf BW-2 Manual de usuario

Lyngdorf

Lyngdorf BW-3 Manual de usuario

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Manual de usuario

REL Acoustics

REL Acoustics Q Series Manual de usuario

Pioneer

Pioneer Elite S-W1EX Manual de usuario

L-Acoustics

L-Acoustics KIVA SB15M Guía de inicio rápido

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Manual de usuario

KEF

KEF KUBE 200 Manual de usuario

Yamaha

Yamaha SW500 Manual de usuario