Panasonic PTL711U - LCD PROJECTOR Manual de usuario

Panasonic

LCD Projector Commercial Use

Operating Instructions

Mqdel No. PT-L71 1U

PT-L701

PT-L501

Read these insirucHons completely bsfore operating this urit.

Dear Panasonic Customer:

This instruction booklet provides all the necessary operating information that

you might require. We hope it will help you to get the most performance out

of your new product, and that you will be pleased with your Panasonic LCD

projector.

The serial number of your product may be found on its back. You should

note it in the space provided below and retain this booklet in case service is

required.

Model number: PT-L71 1U/PT-L701 U/PT-L501

Serial number:

IMPORTANT SAFETY NOTICE

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

Power Supply: This LCD Projector Is designed to operate on 100 V-240 V, 50 Hz/60

Hz AC, house current only.

CAUTION: The AC power cord which is supplied with the projector as an accessory can

only be used for power supplies up to 125 V, 10 A. If you need to use higher

voltages or currents than tiiis, you will need to obtain aseparate 250-V

power cord. If you use the accessory cord in such situations, fire may result.

AVIS: RISQUE DE CHOC ELECTRIQUE.

NEPAS OUVRIR

VORSICHT; zur vermeioung eineselektrischen

SCHLAGESGERATNICHTOFFNEN,

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated "dangerous voltage" within the

product's enclosure that may be of sufficient magnitude to

constitute arisk of electric shock to persons.

The exclamation point within an equilateral triangle is

Intended to alert the user to the presence of important

operating and maintenance (servicing) instructions In the

literature accompanying the product.

CAUTION: This equipment is equipped with a

three-pin grounding-type power

plug. Do not remove the grounding

pin on the power plug. This plug will

only fit agrounding-type power

outlet. This is asafety feature. If you

are unable to insert the plug into the

outlet, contact an electrician. Do not

defeat the purpose of the grounding

plug.

WARNING: This equipment has been tested and found to comply with the

limits for aClass Adigital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in acommercial environment. This equipment

generates, uses, and can radiate radio frequency energy and,

If not installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment in aresidential

area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own

expense.

CAUTION: Any unauthorized changes or modifications to this equipment

will void the users authority to operate.

Contents

Preparation

IMPORTANT SAFETY NOTICE 2

Precautions with regard to safety ....5

Accessories 8

Precautions on handling 9

Location and function of

each part 10

Adjusting the angle of tiit 12

Storing the card remote

control unit 15

Using the remote control unit 16

Inserting the battery 16

Operating range 16

Connections 17

Notes on connections 17

Example of connecting with video

equipments 18

Example of connecting with

computers 19

Setting-up 20

Projection methods 20

Projector position 20

Projection distances 21

Basic Operation

Starting to use 22

Turning on the power 22

Turning off the power 23

About the RGB INPUT monitor 24

About the automatic

setup function 24

On-screen menus 25

Menu screens 25

Menu operation guide 26

White character display of on-screen

items 26

Returning to the previous screen. ...26

Returning asetting to the factory

default 27

Using the freeze function 27

Using the D.ZOOM (digital zoom)

function 28

Correcting keystone distortion 29

Adjusting the picture 30

PICTURE MODE 30

COLOR 30

TINT 30

BRIGHT 30

CONTRAST 30

SHARPNESS 30

TV SYSTEM 31

WHITE BALANCE R/G/B 31

DISPLAY MODE 31

S1 SIGNAL 31

RESIZING 32

Adjusting the position 33

HORIZONTAL POSITION 33

VERTICAL POSITION 33

VIDEO SIZE 33

DOT CLOCK 33

CLOCK PHASE 33

Using the INDEX WINDOW function 34

Using the shutter function 35

Changing the display

language 35

Advanced Operation

Option settings 36

SCREEN DISPUY 36

AUTO KEYSTN 36

AUTO YPB.PR 36

AUTO RGB IN 36

RGB FORMAT 36

BACK COLOR 37

FRONT/REAR 37

DESK/CEILING 37

LAMP POWER 37

WMPTIME 37

FUNC1 37

Using the SERIAL connector 38

Indicators 40

Otiiers

Cleaning and replacing

the air filter 42

Replacing the lamp unit 43

Before asWmg for service 46

Specifications 48

Appendix 50

List of compatible signals 50

Dimensions 51

Trademark acknowledgements 52

NOTES IMPORTANTES

CONCERNANT LA SECURITE 53

Precautions concernant la securite 55

Precautions concernant

la manipulation 59

Remplacement du bloc de lampe...61

Precautions with regard to safety

WARNING

If aproblem occurs (such as no image or no sound) or if you notice

smoke or astrange smell coming from the projector, turn off the power

and disconnect the power cord from the wall outlet.

•Do not continue to use the projector in such cases, othenwise fire or

electric shocks could result.

•Check that no more smoke Is coming out, and then contact an Authorised

Service Center for repairs.

•Do not attempt to repair the projector yourself, as this can be dangerous.

Do not install this projector in aplace which is not strong enough to

take the full weight of the projector.

•If the installation location is not strong enough, it may fall down or tip over,

and severe injury or damage could result.

•Installation work (such as ceiling suspension) should only be carried out

by aqualified technician.

•If installation is not carried out correctly, there is the danger that Injury or

electric shocks may occur.

If foreign objects or water get inside the projector, or if the projector is

dropped or the cabinet is broken, turn off the power and disconnect the

power cord from the wall outlet.

•Continued use of the projector in this condition may result in fire or electric

shocks.

•Contact an Authorised Service Center for repairs.

Do not cover the air filter and the air inlet.

•Doing so may cause the projector to overheat, which can cause fire or

damage to the projector.

Do not overload the wall outlet.

•If the power supply is overloaded (for example, by using too many

adapters), overheating may occur and fire may result.

Do not remove the cover or modify it in any way.

•High voltages which can cause fire or electric shocks are present inside

the projector.

•For any inspection, adjustment and repair work, please contact an

Authorised Service Center.

Clean the power cord plug regularly to prevent it from becoming

covered in dust.

•If dust builds up on the power cord plug, the resulting humidity can

damage the insulation, which could result in fire. Pull the power cord out

from the wall outlet and wipe it with adry cloth.

•If not using the projector for an extended period of time, pull the power

cord plug out from the wall outlet.

Do not do anything that might damage the power cord or the power

cord plug.

•Do not damage the power cord, make any modifications to it, place it near

any liot objects, bend it excessively, twist It, pull It, place heavy objects on

top of it or wrap it into abundle.

•If the power cord is used while damaged, electric shocl<s, short-circuits or

fire may result.

•Ask an Authorised Service Center to carry out any repairs to the power

cord that might be necessary.

Do not handle the power cord plug with wet hands.

•Failure to observe this may result in electric shocks.

Insert the power cord plug securely into the wall outlet.

•If the plug Is not inserted correctly, electric shocks or overheating could

result.

•Do not use plugs which are damaged or wall outlets which are coming

loose from the wall.

Do not place the projector on top of surfaces which are unstable.

•If the projector is placed on top of asurface which is sloped or unstable, it

may fall down or tip over, and injury or damage could result.

Do not place the projector into water or let it become wet.

•Failure to observe this may result in fire or electric shocks.

Do not place liquid containers on top of the projector.

•If water spills onto the projector or gets inside it, fire or electric shocks

could result.

•If any water gets inside the projector, contact an Authorised Service

Center.

Do not insert any foreign objects into the projector.

•Do not insert any metal objects or flammable objects into the projector or

drop them onto the projector, as doing so can result in fire or electric

shocks.

After removing the battery from remote control unit, keep it away from

the reach of children.

•The battery can cause death by suffocation if swallowed.

•If the battery is swallowed, seek medical advice immediately.

Do not allow the -i- and -terminals of the battery to come into contact

with metallic objects such as necklaces or hairpins.

•Failure to observe this may cause the battery to leak, overheat, explode or

catch fire.

•Store the battery in aplastic bag and keep it away from metallic objects.

Insulate the battery using tape or similar before disposal.

•If the battery comes into contact with metallic objects or other batteries, it

may catch fire or explode.

Caution

Do not set up the projector in humid or dusty places or In places where

the projector may come into contact with smoke or steam.

•Using the projector under such conditions may result in fire or electric

shocks.

When disconnecting the power cord, hold the plug, not the cord.

•If the power cord itself is pulled, the cord will become damaged, and fire,

short-circuits or serious electric shocks may result.

Always disconnect all cables before moving the projector.

•Moving the projector with cables still attached can damage the cables,

which could cause fire or electric shocks to occur.

Do not place any heavy objects on top of the projector.

•Failure to observe this may cause the projector to become unbalanced

and fall, which could result in damage or injury.

Do not short-circuit, heat or disassemble the battery or place it into

water or fire.

•Failure to observe this may cause the battery to overheat, leak, explode or

catch fire, and burns or other injury may result.

When inserting the battery, malce sure the polarities (+ and -) are

correct.

•If the battery is inserted incorrectly, it may explode or leak, and fire, injury

or contamination of the battery compartment and surrounding area may

result.

Use only the specified battery.

•If an incorrect battery Is used, it may explode or leak, and fire. Injury or

contamination of the battery compartment and surrounding area may

result.

Do not ioolc into the lens while the projector is being used.

•Strong light is emitted from the projector's lens. If you look directly into this

light, it can hurt and damage your eyes.

Do not bring your hands or other objects close to the air outlet port.

•Heated air comes out of the air outlet port. Do not bring your hands or

face, or objects which cannot withstand heat close to this port, otherwise

burns or damage could result.

Replacement of the lamp unit should only be carried out by aqualified

technician.

•The lamp unit has high internal pressure. It can easily become damaged if

struck against hard objects or dropped, and injury or malfunctions may

result.

Disconnect the power cord plug from the wall outlet as asafety

precaution before carrying out any cleaning.

•Electric shocks can result if this is not done.

Ask an Authorised Service Center to clean inside the projector at least

once ayear.

•If dust is left to build up inside the projector without being cleaned out, It

can result in fire or problems with operation.

•Ills agood idea to clean the inside of the projector before the season for

humid weather arrives. Ask your nearest Authorised Service Center to

clean the projector when required. Please discuss with the Authorised

Service Center regarding cleaning costs.

We are In effort to hold your environment clean. Please bring the non

repairable unit your Dealer or aRecycling Company.

Accessories

Check that all of the accessories shown below have been included with your

projector.

Card remote control unit Lens cover Lithium battery for

(TNQE239 x1 )(TKKL51 39 x1 )remote control unit

(CR2025X1)

Carrying bag (TPEP001 Power cord

x1) (TXFSX02PAEZx1)

Precautions on handling

Cautions regarding transportation

Be sure to attach the lens cover before transporting the projector. ^

The projection iens is extremely susceptible to vibration and shocks. When ^

carrying the projector, use the accessory carrying bag. ^

Cautions regarding setting-up

Observe the following at all times when setting up the projector.

Avoid setting up in places which are subject to vibration or shocks.

If the projector is set up in locations with strong vibration, such as near a

motor, or if it is installed inside avehicle or on board aship, the projector

may be subjected to vibration or shocl^s which can damage the internal parts

and cause malfunctions or accidents. Accordingly, set up the projector in a

place which is free from such vibrations and shocks.

Do not set up the projector near high-voltage power lines or near

motors.

The projector may be subject to electromagnetic interference if it is set up

near high-voltage power lines or motors.

If installing the projector to the ceiling, ask aqualified technician to

carry out all Installation work.

If the projector is to be suspended from the ceiling, you will need to purchase

the separate installation kit {Model No.: ET-PK701). Furthermore, all

installation work should only be carried out by aqualified technician.

Notes on use

In order to get the best picture quality

If outside light or light from indoor lamps is shining onto the screen, the

images projected will not have good contrast. Draw curtains or blinds over

any windows and turn off any fluorescent lights near the screen to prevent

reflection.

Do not touch the surfaces of the lens with your bare hands.

If the surface of the lens becomes dirty from fingerprints or anything else, this

will be magnified and projected onto the screen. Moreover, when not using

the projector, retract the lens and then cover it with the accessory lens cover.

About the screen

If the screen you are using is dirty, damaged or discolored, attractive

projections cannot be obtained. Do not apply any volatile substances to the

screen, and do not let it become dirty or damaged.

Before carrying out cleaning and maintenance, be

sure to disconnect the power cord plug from the

wall outlet.

Wipe the cabinet with asoft, dry cloth.

If the cabinet is particularly dirty, soak the cloth in water with asmall amount

of neutral detergent in it, squeeze the cloth very well, and then wipe the

cabinet. After cleaning, wipe the cabinet dry with adry cloth.

If using achemically-treated cloth, read the instructions supplied with

the cloth before use.

Do not wipe the lens with acloth that is dusty or which produces lint.

If any dust or lint gets onto the lens, such dust or lint will be magnified and

projected onto the screen. Use ablower to clean any dust and lint from the

lens surface, or use asoft cloth to wipe off any dust or lint.

Otros manuales para PTL711U - LCD PROJECTOR

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Proyector de Panasonic

Panasonic

Panasonic PT-LW321 Manual de usuario

Panasonic

Panasonic PTL520U - LCD PROJECTOR Manual de usuario

Panasonic

Panasonic PTL6600U - LCD PROJECTOR Manual de usuario

Panasonic

Panasonic PT-VW430 Guía

Panasonic

Panasonic PTL797U - LCD PROJECTOR Manual de usuario

Panasonic

Panasonic PT-51D31CE Manual de usuario

Panasonic

Panasonic PT-LC50E Manual de usuario

Panasonic

Panasonic PTL758U - LCD PROJECTOR Manual de usuario

Panasonic

Panasonic PT-TW230 Guía

Panasonic

Panasonic PT-51SX60T Manual de usuario

Panasonic

Panasonic VG400LBNS Manual del sistema

Panasonic

Panasonic DLP PT-D12000E Manual de usuario

Panasonic

Panasonic PT-56HX40 Manual de usuario

Panasonic

Panasonic PTL797PXU - LCD PROJECTOR Manual de usuario

Panasonic

Panasonic PT-LB75NTE Manual de usuario

Panasonic

Panasonic PTAE100U - LCD PROJECTOR Manual de usuario

Panasonic

Panasonic PTL711XU - LCD PROJECTOR Manual de usuario

Panasonic

Panasonic PT-AE1000 Manual de usuario

Panasonic

Panasonic PT-AE1000U - LCD Projector - HD 1080p Manual de usuario

Panasonic

Panasonic PT-LZ370U Manual de usuario

Panasonic

Panasonic PT-FZ570U Instrucciones de funcionamiento

Panasonic

Panasonic PT-RZ660 Manual de usuario

Panasonic

Panasonic PT-AE7000U Manual de usuario

Panasonic

Panasonic PTLB80NTU - LCD PROJECTOR Manual de usuario

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Epson

Epson VS400 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

NEC

NEC NP600S EDU Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Epson

Epson PowerLite Pro Cinema 6020UB Manual de usuario

Epson

Epson PowerLite Home Cinema 705HD Manual de usuario

Christie

Christie LHD700 Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario

Asus

Asus ZenBeam Latte Manual de usuario