Panasonic TH-42PX20U/P Operating Manual de usuario

ORDERNO. ITD0309035C1

B19 Canada: B07

High Definition Plasma Television

TH-42PX20U-P

GPH6DU Chassis

SPECIFICATIONS

Specifications

Power

Source AC 120 V, 50 / 60 Hz

Power

Consumption Maximum:595 W

Stand-bycondition :0.9W

Plasma

Displaypanel Drivemethod :AC type42-inch, 16 :9aspect ratio

Screen

Size 36.22 “ (920 mm) (W) × 20.39 “ (518 mm) (H) × 41.57 “ (1056 mm) (diagonal)

Dimensions

× H × D ) 44.88 “ (1140mm) × 29.8“ (757 mm) × 5.47 “ (139 mm)

Mass

(Weight) 90.4lb.(41 kg)Net

Channel

Capability-181 VHF-12 :UHF-56 :Cable-125

Sound

Speaker Woofer 80mm × 2, Tweeter 16mm × 73mm × 8

AudioOutput 26 W[ 5W+ 5W, 8W+ 8W] (10 %THD )

Headphone M3(3.5mm) Jack × 1

FEATURES

Twoscreendisplayfuctions 3D Y / C FILTER

BBE VIVA LINEAR PIP

CLOSED CAPTION V-Chip

Accessories

Supplied Remotecontrol Transmitter EUR7603ZB0

AA Battery× 2 Ferritecores (large× 5, small × 5)

AC Cord F typeAntennaAdaptor(3C-2V × 2, 5C-2V × 2)

Pedestal

Operating

Conditions Temperature : 34 ° F- 104 ° F(0° - 40 ° C)

Humidity: 20 %- 80 %(non-condensing)

Connection

Terminals RGB input D-SUB 15pin R, G, B / 0.7Vp-p(75 )

HD, VD / 1.0-5.0Vp-p(high

impedance)

AV INPUT1-3 VIDEO

(Phono Jack Type) 1.0Vp-p(75 )

S-VIDEO

(Mini DIN 4-pin) Y :1.0Vp-p(75 ), C : 0.286

(75 )

AUDIO L-R

(Phono Jack Type× 2) 0.5Vrms

AV PROG.OUT VIDEO

(Phono Jack Type) 1.0Vp-p(75 )

AUDIO L-R

(Phono Jack Type× 2) 0.5Vrms

TO AUDIO AMP AUDIO L-R

(Phono Jack Type× 2) 0.5Vrms

COMPONENTVIDEO Y 1.0Vp-p(including

synchronization)

INPUT1-2 PB / PR ±0.35 Vp-p

AUDIO L-R

(Phono Jack Type× 2) 0.5Vrms

HDMI INPUT HDMI typeAconnector

AUDIO L-R

(Phono Jack Type× 2) 0.5Vrms

Note

Design

and Specifications are subject tochange without notice.Weight and Dimensions shownare

approximate.

Unauthorized copying and distribution isaviolation of law.

1. Applicable signals

2. Safety Precautions

2.1. General Guidelines

1. When servicing, observe the original lead dress. Ifashort circuit

isfound, replace all parts which have been overheated or

damaged bythe short circuit.

2. After servicing, see to itthat all the protective devices such as

insulation barriers, insulation papers shields are properly

installed.

3. After servicing, make the following leakage current checks to

prevent the customer from being exposed to shock hazards.

2.1.1. Leakage Current ColdCheck

1. Unplug the AC cord and connect ajumper between the two

prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between the

jumpered AC plug and each exposed metalliccabinet part on the

equipment such as screwheads, connectors, control shafts, etc.

When the exposed metallicpart has areturn path to thechassis,

the reading shouldbe between 1M and 5.2M . / When the

exposed metal does not have areturn path to the chassis, the

reading must be . Figure 1

2.1.2. Leakage Current Hot Check (See Figure 1 .)

1. Plug the AC cord directlyinto the AC outlet. Donot use an

isolation transformer for thischeck.

2. Connect a1.5k , 10 watts resistor, inparallel with a0.15 F

capacitors, between each exposed metallicpart on the set and a

good earth ground such as awater pipe, as shownin Figure 1.

3. Use an AC voltmeter, with 1000 ohms/voltor more sensitivity, to

measure the potential across the resistor.

4. Check each exposed metallicpart, and measure the voltage at

each point.

5. Reverse the AC plug inthe AC outlet and repeat each of the above

measurements.

6. The potential at anypoint shouldnot exceed 0.75 volts RMS. A

leakage current tester (Simpson Model 229 or equivalent) maybe

used to make the hot checks, leakage current must not exceed 1/2

milliamp. Incase ameasurement isoutsideof the limits specified,

there isapossibilityof ashock hazard, and the equipment should

be repaired and rechecked before itisreturned to the customer.

3. Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices

Some semiconductor(solidstate) devices canbe damagedeasilybystatic electricity. Such

components commonlyare calledElectrostaticallySensitive (ES) Devices. Examples of typical

ES devices are integratedcircuits and some field-effect transistorsand semiconductor"chip"

components. The following techniques shouldbe usedtohelpreduce the incidence of

component damage causedbyelectrostatic discharge (ESD).

1. Immediatelybefore handling anysemiconductor component or

semiconductor-equipped assembly, drainoff anyESDon your

bodybytouching aknownearth ground. Alternatively, obtainand

wear acommerciallyavailabledischarging ESDwrist strap,

whichshouldbe removed for potential shock reasons prior to

applying power to the unitunder test.

2. After removing an electrical assemblyequipped with ES devices,

place the assemblyon aconductive surface such as alminum foil,

to prevent electrostaticcharge buildup or exposure of the

assembly.

3. Use onlyagrounded-tipsoldering iron to solder or unsolder ES

devices.

4. Use onlyan anti-staticsolder removal device. Some solder

removal devices not classified as "anti-static(ESDprotected)"

can generate electrical charge sufficient to damage ES devices.

5. Donot use freon-propelled chemicals. These can generate

electrical charges sufficient to damage ES devices.

6. Donot remove areplacement ES device from its protective

package until immediatelybefore you are readyto install it. (Most

replacement ES devices are packaged with leads electrically

shorted together byconductive foam, alminum foil or

comparableconductive material).

7. Immediatelybefore removing the protective material from the

leads of areplacement ES device, touch the protective material to

the chassisor circuitassemblyinto which the device will be

installed.

Caution

Besure no power isapplied to the chassisor circuit, and observe

all other safetyprecautions.

8. Minimize bodilymotions when handling unpackaged replacement

ES devices. (Otherwise hamless motion such as the brushing

together of your clothes fabricor the lifting of your foot from a

carpeted floor can generate staticelectricity(ESD)sufficient

todamage an ES device).

4. About lead free solder (PbF)

Note: Leadis listedas (Pb) inthe periodic table of elements.

Inthe information below, Pbwill refertoLeadsolder, and PbF will refertoLeadFree Solder.

The LeadFree Solderusedinourmanufacturing process and discussedbelowis (Sn+Ag+Cu).

That is Tin(Sn), Silver(Ag) and Copper(Cu) although othertypes are available.

This model uses PbFree solderinit’s manufacture due toenvironmental conservation issues.

Forservice and repairwork, we’dsuggest the use of Pbfree solderas well, although Pbsolder

maybe used.

PCBs manufacturedusing leadfree solderwill have the PbF withina leaf Symbol

stampedon the back of PCB.

Caution

-Pb free solder has ahigher melting point than standard solder.

Typicallythe melting point is50 ~ 70 °F (30~40 °C)higher. Please

use ahigh temperature soldering iron and set itto 700 ± 20 °F (370

± 10 °C).

-Pb free solder will tend to splash when heated too high (about 1100

°F or 600 °C).

Ifyou must use Pb solder, please completelyremove all of the Pb

free solder on the pins or solder area before applying Pb solder. If

thisisnot practical, be sure to heat the Pb free solder until it

melts, before applying Pb solder.

-After applying PbF solder to doublelayered boards, please check

the component side for excess solder which mayflow onto the

opposite side. (see figure below)

SuggestedPbfree solder

There are several kinds of Pbfree solderavailable forpurchase. This product uses Sn+Ag+Cu

(tin, silver, copper) solder. However, Sn+Cu(tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder

canalsobeused.

5. Service Hint

BoardName Function BoardName Function

C1 DATA DRIVER (UPPER

RIGHT) PF LINE FILTER

C2 DATA DRIVER (UPPER

LEFT) SC SCAN DRIVE

D DIGTALSIGINALPROCESS SD SCAN OUT(DOWN)

DG DIGTALCORE MICOM SS SUSTAIN DRIVE

GFRONTTERMINAL, SWITCH SS2 SUSTAIN CONNECTION (UP)

H REAE TERMINAL SS3 SUSTAIN CONNECTION

(DOWN)

KLED, REMOTE, SU SCAN OUT(UP)

P POWER SUPPLY TA MAIN TUNER

PA DC/DC, AUDIO TB SUB TUNER

C3 DATA DRIVER (LOWER

RIGHT) JG PC/SD CARD

C4 DATA DRIVER (LOWER

LEFT) DV HDMI

S POWER SW

6. Location of Lead Wiring

6.1. Lead of Wiring (1)

6.2. Lead of Wiring (2)

6.3. Lead of Wiring (3)

Otros manuales para TH-42PX20U/P Operating

Tabla de contenidos

Otros manuales de Televisor de plasma de Panasonic

Panasonic

Panasonic Viera TC-P55S60 Manual de usuario

Panasonic

Panasonic TH-58PX60U Manual de usuario

Panasonic

Panasonic VIERA TH-42PZ700A Manual de usuario

Panasonic

Panasonic Viera TH-50PH11 Guía del usuario

Panasonic

Panasonic TH-P58V10M Manual de usuario

Panasonic

Panasonic Viera TH-42PX74EA Manual de usuario

Panasonic

Panasonic Viera TH-P42X50D Manual de usuario

Panasonic

Panasonic TX-P50GT60E Manual de usuario

Panasonic

Panasonic VIERA TC-P42S30 Manual de usuario

Panasonic

Panasonic VIERA TH-58PZ800U Manual de usuario

Panasonic

Panasonic TX-P42ST60B Manual de usuario

Panasonic

Panasonic TC-P42X60 Manual de instrucciones

Panasonic

Panasonic Viera TC-P58VT25 Manual de usuario

Panasonic

Panasonic TH-42PV8DA Manual de usuario

Panasonic

Panasonic TC-P50G20 Quick Setup Guide (English Guía de configuración

Panasonic

Panasonic TC-P42U1 - 42" Plasma TV Manual de usuario

Panasonic

Panasonic Viera TC-P42S1 Manual de usuario

Panasonic

Panasonic Viera TH-37PV60E Manual de usuario

Panasonic

Panasonic Viera TC-P60UT50 Manual de usuario

Panasonic

Panasonic Viera TC-46PGT24 Manual de usuario

Panasonic

Panasonic Viera TX-P65VT50E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Guía de configuración

Panasonic

Panasonic TH-50PY850H Manual de usuario

Panasonic

Panasonic TH-42PX6U Manual de usuario

Manuales populares de Televisor de plasma de otras marcas

Hitachi

Hitachi 50PD9800TA Manual de usuario

Pioneer

Pioneer PDP-LX508G Manual de usuario

LG 60PM9700 Manual de usuario

LG 50PX4D Manual de usuario

LG 60PA5500 Manual de usuario

Sony

Sony WEGA KE-P42M1 Manual de usuario

VESTEL

VESTEL PL2000 Manual de usuario

VisionQuest

VisionQuest PVQ-32VGB Manual de usuario

Maxent

Maxent MX-5020HPM Manual de usuario

XOCECO

XOCECO PH-42T8 Manual de usuario

Maxent

Maxent MX-42VM7 Manual de usuario

Sampo

Sampo PME-42S6 Manual de usuario

Hitachi

Hitachi 32PD7800 Manual de usuario

LG 50PK550 Manual de usuario

Haier

Haier P42A1-AK Manual de usuario

Insignia

Insignia NS-42P650A11 Manual de usuario

Hitachi

Hitachi 42PD3200A Manual de usuario

LG 50PS70FD-AA Manual de usuario