Panasonic TH-42PE55E Manual de usuario

ORDERNO.PCZ0509087C2

Digital Progressive Wide Plasma Television

TH-42PE55E / TH-37PE55E

GP8DEChassis

SPECIFICATIONS

Specifications

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Power

Source AC 220-240 V, 50 / 60 Hz

Power

Consumption Averageuse : 253 W(TH-37PE55E)

Averageuse : 323 W(TH-42PE55E)

Standbycondition : 0.3W(Without Tuner Lock On)

Standbycondition : 16 W(WithTuner Lock On)

Plasma

Displaypanel

Drivemethod AC type

Aspect Ratio 16:9

Contrast Ratio 4000:1

Visiblescreensize

(No.of pixels) 818 mm (W) × 461 mm (H) × 939 mm (diagonal) (37-inch)

920 mm (W) × 518 mm (H) × 1,056 mm (diagonal) (42-inch)

408,960 (852 (W) × 480 (H)) [2,556 × 480 dots]

Sound

Speaker 12 cm × 6cm × 2pcs, 6

AudioOutput 16 W(8W+ 8W), 10%THD

Scanning

format 480i(60Hz), 480p(60Hz), 576i(50Hz), 576p(50Hz), 720p(50Hz), 720p(60Hz), 1080i(50Hz), 1080i(60Hz)

Receiving

Systems

Band name PALB, G

VHFE2- E12 UHFE21 - E69

CATV (S01 - S05) CATV S1- S10 (M1- M10)

CATV S11 - S20 (U1- U10) CATV S21 - S41 (Hyperband)

PAL525/60

Playback of NTSC tapefromsome PALVideorecorders (VCR)

DVB

Digital terrestrial services viaVHF/ UHFaerial input.

M.NTSC

Playback fromM. NTSC Videorecorders (VCR)

NTSC (AV input only)

Playback fromNTSC Videorecorders (VCR)

Aerial

- Rear UHF/ VHF

Operating

Conditions Temperature : 0°C - 40 °C

Humidity: 20 %- 80 %RH (non-condensing)

Connection

Terminals

AV1(Scart connector) 21 Pinterminal (Audio/Videoin, Audio/Videoout, RGB in)

AV2(Scart connector) 21 Pinterminal (Audio/Videoin, Audio/Videoout, S-Videoin, Q-Link)

AV3(Scart connector) 21 Pinterminal (Audio/Videoin, Audio/Videoout, RGB in, S-Videoin, Q-Link)

Other Inputs

COMPONENT Y 1.0Vp-p(including synchronization)

PB, PR±0.35 Vp-p

HDMI TYPE AConnector

AUDIO L- R RCAPIN Type× 2 0.5Vrms

Output

AUDIO L- R RCAPIN Type× 2 0.5Vrms (high impedance)

Dimensions

( W× H × D ) 968 mm × 641 mm × 96.5mm (37-inch)

1,068 mm × 701 mm × 96.5mm (42-inch)

Weight

28.5kgNet (37-inch)

33 kgNet (42-inch)

Notes

-Design and Specifi cationsaresubject to changewithoutnotice. Weightand Dimensionsshown areapproximate.

-Thisequipmentcomplies with theEMC standardslisted below.

EN55013, EN61000-3-2, EN61000-3-3, EN55020

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Unauthorized copying and distribution isaviolation of law.

1. Applicable signals

2. Safety Precautions

2.1. General Guidelines

1. When servicing, observe the original lead dress. Ifashort circuit

isfound, replace all parts which have been overheated or

damaged bythe short circuit.

2. After servicing, see to itthat all the protective devices such as

insulation barriers, insulation papers shields are properly

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

installed.

3. After servicing, make the following leakage current checks to

prevent the customer from being exposed to shock hazards.

2.2. Touch-Current Check

1. Plug the AC cord directlyinto the AC outlet. Donot use an

isolation transformer for thischeck.

2. Connect ameasuring network for touch currents between each

exposed metallicpart on the set and agood earth ground such as

awater pipe, as shownin Figure 1.

3. Use Leakage Current Tester (Simpson 228 or equivalent) to

measure the potential across the measuring network.

4. Check each exposed metallicpart, and measure the voltage at

each point.

5. Reserve the AC plug inthe AC outlet and repeat each of the above

measure.

6. The potential at anypoint (TOUGHCURRENT) expressed as

voltage U1and U2, does not exceed the following values:

For a. c.:U1= 35 V(peak) and U2= 0.35 V(peak);

For d. c.:U1= 1.0V,

Note:

The limit value of U2= 0.35 V (peak) fora. c. and U1= 1.0 V ford. c. correspond tothe values 0.7

mA (peak) a. c. and 2.0 mA d. c.

The limit value U1= 35 V (peak) fora. c. correspond tothe value 70 mA (peak) a. c. for

frequencies greaterthan100 kHz.

7. Incase ameasurement isout of the limits specified, there isa

possibilityof ashock hazard, and the equipment shouldbe

repaired and rechecked before itisreturned to the customer.

Figure 1

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

3. Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices

Some semiconductor(solidstate) devices canbe damagedeasilybystatic electricity. Such

components commonlyare calledElectrostaticallySensitive (ES) Devices. Examples of typical

ES devices are integratedcircuits and some field-effect transistors and semiconductor"chip"

components. The following techniques shouldbe usedtohelpreduce the incidence of

component damage causedbyelectrostatic discharge (ESD).

1. Immediatelybefore handling anysemiconductor component or

semiconductor-equipped assembly, drainoff anyESDon your

bodybytouching aknownearth ground. Alternatively, obtainand

wear acommerciallyavailabledischarging ESDwrist strap, which

shouldbe removed for potential shock reasons prior to applying

power to the unitunder test.

2. After removing an electrical assemblyequipped with ES devices,

place the assemblyon aconductive surface such as alminum foil,

to prevent electrostaticcharge buildup or exposure of the

assembly.

3. Use onlyagrounded-tipsoldering iron to solder or unsolder ES

devices.

4. Use onlyan anti-staticsolder removal device. Some solder

removal devices not classified as "anti-static(ESDprotected)"

can generate electrical charge sufficient to damage ES devices.

5. Donot use freon-propelled chemicals. These can generate

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

electrical charges sufficient to damage ES devices.

6. Donot remove areplacement ES device from its protective

package until immediatelybefore you are readyto install it. (Most

replacement ES devices are packaged with leads electrically

shorted together byconductive foam, alminum foil or comparable

conductive material).

7. Immediatelybefore removing the protective material from the

leads of areplacement ES device, touch the protective material to

the chassisor circuitassemblyinto which the device will be

installed.

Caution

Besure no power isapplied to the chassisor circuit, and observe

all other safetyprecautions.

8. Minimize bodilymotions when handling unpackaged replacement

ES devices. (Otherwise hamless motion such as the brushing

together of your clothes fabricor the lifting of your foot from a

carpeted floor can generate staticelectricity(ESD)sufficient to

damage an ES device).

4. About lead free solder (PbF)

Note: Leadis listedas (Pb) inthe periodic table of elements.

Inthe information below, Pbwill refertoLeadsolder, and PbF will refertoLeadFree Solder.

The LeadFree Solderusedinourmanufacturing process and discussedbelowis (Sn+Ag+Cu).

That is Tin(Sn), Silver(Ag) and Copper(Cu) although othertypes are available.

This model uses PbFree solderinit’s manufacture due toenvironmental conservation issues.

Forservice and repairwork, we’dsuggest the use of Pbfree solderas well, although Pbsolder

maybe used.

PCBs manufacturedusing leadfree solderwill have the PbF withina leaf Symbol

stampedon the back of PCB.

Caution

-Pb free solder has ahigher melting point than standard solder.

Typicallythe melting point is50 ~ 70 °F (30~40 °C)higher. Please

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

use ahigh temperature soldering iron and set itto 700 ± 20 °F (370

± 10 °C).

-Pb free solder will tend to splash when heated too high (about 1100

°F or 600 °C).

Ifyou must use Pb solder, please completelyremove all of the Pb

free solder on the pins or solder area before applying Pb solder. If

thisisnot practical, be sure to heat the Pb free solder until it

melts, before applying Pb solder.

-After applying PbF solder to doublelayered boards, please check

the component side for excess solder which mayflow onto the

opposite side. (see figure below)

SuggestedPbfree solder

There are several kinds of Pbfree solderavailable forpurchase. This product uses Sn+Ag+Cu

(tin, silver, copper) solder. However, Sn+Cu(tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder

canalsobe used.

5. Service Hint

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

BoardName Function BoardName Function

PPowerSupply D Format Converter, Plasma AI

Processor

PA DC-DC Converter, PowerSOS Z SpeakerAMP

PB AudioPower C1 Data Driver(Left)

H AV Terminal, AV Switch, MSP C2 Data Driver(Right)

TA Tuner SC ScanDrive

DV HDMI Interface

None serviceable

DV-Boardshouldbe exchanged

forservice.

SU Scanout (Upper)

SD Scanout (Lower)

SS SustainDrive

XV D-TV Interface K Remote receiver, Keyscan

DG Digital Signal Processor S PowerSwitch

6. Plasma panel replacement method

6.1. Remove the Back cover.

1. See Service Hint (Section 5).

6.2. Remove the P-Board.

Caution:

To remove P.C.B., wait1minute after power was off for discharge

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

from electrolisiscapacitors.

1. Disconnect the couplers (P2, P5, P9, P10, P11, P12, P23 and P25).

2. Remove the screws(×5 )and remove the P-Board.

6.3. Remove the PB-Board

1. Unlock the cableclampers to free the cable.

2. Disconnect the couplers (PB5and PB7).

3. Remove the screws(×3 )and remove the PB-Board metal frame.

4. Remove the screws(× 4 )and remove the PB-Board.

6.4. Remove the D-Board

1. Remove the PB-Board.

2. Disconnect the couplers (D3, D5, D20 and D25).

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

3. Disconnect the flexiblecables (D33 and D34).

4. Remove the screws(×4 )and remove the D-Board.

6.5. Remove the rear terminal cover

1. Remove the screws(×4 , ×7 , ×2 ).

2. Remove the rear terminal cover.

6.6. Remove the metal frame

1. Unlock the cableclampers to free the cable.

2. Disconnect the couplers (D3, D5, H7, P10 and PB7) and relay

connector (SP-R, SP-L).

3. Remove the screws(×5 )remove the metal frame.

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Televisor de plasma de Panasonic

Panasonic

Panasonic Viera TH-65PV600A Manual de usuario

Panasonic

Panasonic TH-42PX600U Manual de usuario

Panasonic

Panasonic TH-42PA20U/P Manual de usuario

Panasonic

Panasonic Viera TC-P60UT50 Manual de usuario

Panasonic

Panasonic Viera TC-P42X60H Manual de usuario

Panasonic

Panasonic TH-103PB1U Manual de usuario

Panasonic

Panasonic Viera TH-37PX80B Manual de usuario

Panasonic

Panasonic TC-P60ST50 Series Manual de usuario

Panasonic

Panasonic TH-42PA20A Manual de usuario

Panasonic

Panasonic Viera TC-P42U2 Manual de usuario

Panasonic

Panasonic TH-50PX60U Manual de usuario

Panasonic

Panasonic Viera TC-65PS64 Manual de usuario

Panasonic

Panasonic TX-P50GT60E Manual de usuario

Panasonic

Panasonic TH37PX50U - 37" HD PLASMA TV Guía de inicio rápido

Panasonic

Panasonic TC-58PS14 Manual de usuario

Panasonic

Panasonic TC-P50X60 Manual de usuario

Panasonic

Panasonic TH-50PV80D Manual de usuario

Panasonic

Panasonic Viera TH-42PZ70B Manual de usuario

Panasonic

Panasonic Viera TH-37PV7P Manual de usuario

Panasonic

Panasonic TC-P55VT60 Manual de usuario

Panasonic

Panasonic TC-P54V10 - Viera 54" Full HD 1080p Manual de usuario

Panasonic

Panasonic TH-37PW4 Manual de usuario

Panasonic

Panasonic TC-P50U20P Manual de usuario

Panasonic

Panasonic Viera TH-42PX74EA Manual de usuario

Manuales populares de Televisor de plasma de otras marcas

Hitachi

Hitachi 50PD9800TA Manual de usuario

Pioneer

Pioneer PDP-LX508G Manual de usuario

LG 60PM9700 Manual de usuario

LG 50PX4D Manual de usuario

LG 60PA5500 Manual de usuario

Sony

Sony WEGA KE-P42M1 Manual de usuario

VESTEL

VESTEL PL2000 Manual de usuario

VisionQuest

VisionQuest PVQ-32VGB Manual de usuario

Maxent

Maxent MX-5020HPM Manual de usuario

XOCECO

XOCECO PH-42T8 Manual de usuario

Maxent

Maxent MX-42VM7 Manual de usuario

Sampo

Sampo PME-42S6 Manual de usuario

Hitachi

Hitachi 32PD7800 Manual de usuario

LG 50PK550 Manual de usuario

Haier

Haier P42A1-AK Manual de usuario

Insignia

Insignia NS-42P650A11 Manual de usuario

Hitachi

Hitachi 42PD3200A Manual de usuario

LG 50PS70FD-AA Manual de usuario