Panasonic KX-TDA30 Manual de usuario
Hybrid IP-PBX
Getting Started
1 Before Installation
2 Installation
3 Starting the Hybrid IP-PBX
4 Customising the Hybrid IP-PBX
5 Confirming the Connection
Table of Contents
........................... 2
........................................ 4
............. 11
..... 14
............ 20
Thank you for purchasing the Panasonic Hybrid IP-PBX, KX-TDA30.
Please read this manual carefully before using this product and save this manual for future use.
KX-TDA30: Version 1.0
Model no. KX-TDA30
2 Getting Started
1 Before Installation
1.1 System Connection Diagram
*1 In addition to the supplied AC adaptor, an optional AC adaptor can be connected to the Hybrid IP-PBX.
*2 The Hybrid IP-PBX has 4 super hybrid ports pre-installed.
SLT Wireless Phone Fax Machine
PCKX-T7636/
KX-T7633
DSS
Console
Doorphone & Door Opener
AC Cord & AC Adaptor
*1
IP-type
Private Network
Station Message
Detail Recording (SMDR)
PC
Router
ISDN BRI Line
ISDN BRI Line
(Digital Trunk)
(Digital Trunk)
ISDN BRI Line
(Digital Trunk)
LCOT4
(KX-TDA3180)
DLC8
(KX-TDA3172)
DLC4
(KX-TDA3171)
SLC8
(KX-TDA3174)
SLC4
(KX-TDA3173)
DPH4
(KX-TDA3161)
DPH2
(KX-TDA3162)
ECHO8
(KX-TDA3166)
EXT-CID
(KX-TDA3168)
MSG2
(KX-TDA3191)
IP-GW4
(KX-TDA3480)
Analogue
Analogue
Trunk
Trunk
Analogue
Trunk
Telephone
Company
SLT Wireless Phone Fax Machine
Hybrid IP-PBX
DPT
APT
DPT DSS Console
Voice
Processing
System
Voice
Processing
System
Radio
Amplifier Pager/Speaker
Server PC
CID4
(KX-TDA3193)
CS PS
4 Super Hybrid Ports
*2
CS PS
Batteries
Main Board
RMT
(KX-TDA3196)
KX-T7600 DPT KX-T7600 DPT
for Single Line Device
for Digital Proprietary
Telephone (DPT)
and DSS Console
for Single Line Device,
DPT/Analogue
Proprietary Telephone
(APT), DSS Console,
and Portable Station (PS)
BRI2
(KX-TDA3280)
Getting Started 3
1.2 Unpacking
Check the package contents.
Main Unit ×1
CD-ROM (including manuals, etc.) ×1
Necessary tools (not supplied):
Telephone cable for extension connection:
The maximum length of the cable may vary depending on the type of the cables.
An RS-232C or USB cable for PC connection
Connectors (RJ45/RJ11)* for trunk and extension connections
Note
• Use a twisted pair cable for the RJ45 or RJ11 connector.
AC Cord* ×1 AC Adaptor ×1Screw×5
Washer × 5 Mini Plug (for pager and
music source) ×2
SD Memory Card ×1
Main Strap ×1 Optional Card Label Sheet ×1
* The type of the AC cord may vary depending on the country/area of use.
Diameter of cable
(ø 0.4 mm to ø 0.6 mm)
Maximum length of cable
ø 0.5 mm 1128 m for SLT
ø 0.5 mm 720 m for KX-T7600 series
ø 0.5 mm 229 m for other DPT, APT and DSS Console
* The connector type may be RJ45 or RJ11 depending on the country/area.
4 Getting Started
2Installation
2.1 Opening/Closing the Covers
Opening the Covers
1. Pull the slide button to the right and, holding it, slide the cable cover upwards. Then turn
the cable cover slightly to remove it.
2. Remove the three screws.
3. Holding the protrusions on both sides of the front cover, swing the cover open.
Slide Button
Cable Cover
Screw
Getting Started 5
Closing the Covers
1. Close the front cover, then tighten the three screws.
2. Attach the rear hooks on the cable cover to the main unit, then swing the cable cover
closed so that the front hooks fit in place.
3. Slide the cable cover down until it locks.
Screw
Cable Cover
6 Getting Started
2.2 Installing the SD Memory Card
The SD Memory Card contains software for all the processes of the Hybrid IP-PBX and all the
customer data. The SD Memory Card must be inserted before start up.
CAUTION
Do not remove the SD Memory Card during the operation of the Hybrid IP-PBX.
Removing the SD Memory Card during operation may cause damage to the SD Memory
Card, or result in loss of data.
SD Memory Card
Slot Cover
SD Memory
Card
Getting Started 7
2.3 Installing the Optional Service Cards
Slot Position
Slot Condition
The following table shows the slot condition. " " indicates that the slot supports the optional
service card.
CAUTION
To protect the main board from static electricity, do not touch parts on the main board or
on the optional service cards. To discharge static, touch ground or wear an earthing strap.
*1Slot s 10 and 11 supports only cards which do not have external ports. Therefore, these
slots do not have removable cover plates.
*2Slot 01 is the pre-installed super hybrid ports. No optional service card can be installed.
Card Slot Number
Type Max 02030405060708091011
LCOT4 3
BRI2 3
DLC4
1*1
*1 Only one of either DLC4 or SLC4 card can be installed.
SLC4
IP-GW4 1
DLC8
2*2
*2 A maximum of two DLC8 cards, two SLC8 cards, or one of each card can be installed.
SLC8
DPH4
1*3
*3 Only one of either DPH4 or DPH2 card can be installed.
DPH2
ECHO8 1
EXT-CID 1
MSG2 2
02
03
04
05
06
07
08
09
10
*
1
11
*
1
01
*
2
8 Getting Started
Installing the Trunk/Extension Cards
1. Before installing the optional service cards, cut and remove the appropriate dummy cover
plates from the main unit.
CAUTION
For safety reasons, smooth the cut edges after removing the dummy cover plates.
2. Position the card in the open slot, making sure that the tabs on the both sides of the card
fit into place. Then, holding the card firmly in place, lower the rear end so that the hole of
the card fits over the extension bolt.
3. Insert the new extension bolt (included with the card) into the hole on the card, and tighten
it to secure the card.
Dummy Cover Plate
1
2
Extension Bolt
Optional Service Card
Extension Bolt
Getting Started 9
2.4 Installing the Trunk Cards
LCOT4 Card
Accessory (included): Extension Bolt ×1, Strap ×1
User-supplied (not included): RJ45 connector or RJ11 connector*
BRI2 Card
Accessory (included): Extension Bolt ×1, Strap ×1
User-supplied (not included): RJ45 connector
Notes
•Connect this optional service card to the trunk through an NT1; do not connect to the
U interface of the trunk directly.
•This optional service card has 100 of terminal resistance. For use in point to multi-
point connection, the card must be placed at the end of the bus.
* The connector type may be RJ45 or RJ11 depending on the country/area.
To trunk
RJ45
To NT1
RJ45 (LINE 1)
RJ45 (LINE 2)
10 Getting Started
2.5 Installing the Extension Cards (DLC4/DLC8/SLC4/
SLC8)
Accessory (included): Extension Bolt ×1, Strap ×1
User-supplied (not included): RJ45 connector or RJ11 connector*
2.6 Connecting Extensions
* The connector type may be RJ45 or RJ11 depending on the country/area.
Example: DLC4 Card
To extension
RJ45
To extension card
RJ11
Example: KX-T7600 Series DPT
DPT and DSS Console
KX-T7000 Series SLT
Pin Assignments
H L
T R
APT
HTRL
TO MAIN UNIT
/ PABX
H L
Otros manuales para KX-TDA30
18
Tabla de contenidos
Otros manuales de Centralita privada de Panasonic
Panasonic
Panasonic KX-TVP200 Manual de usuario
Panasonic
Panasonic KX-TDE100 Manual de usuario
Panasonic
Panasonic KX-NS1000 Manual de usuario
Panasonic
Panasonic KX-HGT100-B Manual de usuario
Panasonic
Panasonic KX- TAW848 Manual de usuario
Panasonic
Panasonic KX-NS300 Guía de instalación
Panasonic
Panasonic KX-TA824 Manual del propietario
Panasonic
Panasonic KX-TDE100 Manual de usuario
Panasonic
Panasonic KX-TVS50 - 2 Port Voicemail System Manual de usuario
Panasonic
Panasonic KX-TD612NZ Manual de usuario
Panasonic
Panasonic HYBRID IP-PBX KX-TDA100 Manual de usuario
Panasonic
Panasonic KX-TA624 Manual de usuario
Panasonic
Panasonic KX-TDA50 Manual de usuario
Panasonic
Panasonic KX-NCP500 Instrucciones de montaje
Panasonic
Panasonic KX-TDE200NZ Manual de usuario
Panasonic
Panasonic KX-TA624 Manual de usuario
Panasonic
Panasonic KX-NCP500GR Manual de usuario
Panasonic
Panasonic KX-T7625 - Digital Proprietary Speakerphone 24... Manual de usuario
Panasonic
Panasonic KX-TVS50 - 2 Port Voicemail System Manual de usuario
Panasonic
Panasonic KXTD7690 - BTS 2.4 GHZ WIRELESS Manual de usuario
