Panasonic TH-85PF12UK Manual de usuario
(The ratings and appearance are subject to change without notice.)
Temperature: 0°C to 40°C (Multi-system: 0°C to 35°C)
Environmental requirements Humidity: 20% to 80%
2,000,000:1Dynamic contrast
W 2,194 x H 1,480 x D 549 mmPackage size
Altitude: 0 to 2,800 m
Possible (without additional fans, with the power button side up.)Installation in portrait orientation
Audio output
Power supply
Display panel
Power consumption
Weight
Screen size
Dimensions (W x H x D)
Audio line-out
Compliant with the requirements of the destination country
Applied (AGLR finish)AR coating 40 WSlot power supply 0 to 2,800 mAltitude 6,144 shades of gray (equivalent)Gray scale levels
40000:1Contrast 1,920 x 1,080 pixels [1 pixel = 3 cells (RGB)]Number of pixels (H x V)
1,250W
1899/1062/2167 mm
PDP: 125 kg / With the package: Approx. 160 kg (*1)
W 2,015 x H 1,195 x D 99 mm
TH-85PF12U/K/W
*1: When a plastic pallet is used (The specifications have yet to be determined.)
zInstall the PDP in accordance with applicable laws and regulations of the
destination country/region.
zThe installation work must be carried out only by professionals.
zThe power supply for this PDP must meet the requirements of the destination
country. The rated power consumption is TBD.
It is recommended that the PDP use a dedicated power line.
zProvide adequate ventilation in the installation location so that the ambient
temperature will not exceed 40°C.
Make a clearance of 100 mm or more above and on both sides of the PDP and a
clearance of 150 mm or more behind the PDP.
zThe length of the power cord supplied with the PDP is 3 m.
zPosition of the center of gravity (Reference)
Horizontal and vertical center of gravity: The center of the set
Depth from the front to the center of gravity of the set
PDP alone: 33 mm
With the wall mount bracket: 51 mm
zEye bolt type
The size of the eye bolts on the PDP (two on the left and right sides and three on
the top) is M12-20 mm.
(Subject to change without notice due to improvements of the product specifications and/or design.)
(Subject to change without notice due to improvements of the product specifications and/or design.)
zStationary stand
The height of the PDP bottom side is 62.5 mm from the stationary stand. The PDP
can be set 50 mm higher to avoid interference between the PDP and the stand due
to the attachment of a touch panel or for other reasons. At the higher position, the
height of the PDP bottom side is 112.5 mm.
To prevent the stand from tipping over, fix the stand to the table by four points using
the supplied bands. In addition, fix the PDP to the wall by two points using strong
wires.
The stationary stand weighs 55 kg, and the total weight including the PDP is about
180 kg. Do not install the stand with the PDP in a location that cannot withstand the
load.
To prevent the PDP from coming off the mounting bracket, fix the PDP with M8 bolts.
zFloor stand
With the floor stand, the PDP height is adjustable to three different levels.
The height of the PDP bottom side is 1,000 mm/900 mm/800 mm from the floor
stand.
To prevent the stand from tipping over, fix the PDP by four points using adjusters. In
addition, fix the PDP to the wall by two points using strong wires.
To prevent the PDP from coming off the mounting bracket, fix the PDP with M8 bolts.
(Subject to change without notice due to improvements of the product specifications and/or design.)
A
B
2,1951,000
2,095900
1,995800
BA
zStand specifications (Model No.: TY-ST85PF12)
Dimensions: W 1,425 x H 1,413 to 1,606 x D 871 mm
Weight: 75.0 kg
Height adjustable to three levels
(Subject to change without notice due to improvements of the product specifications and/or design.)
zStand specifications (Model No.: TY-ST85P12)
Dimensions: W 1,401 x H 727 x D 443 mm
Weight: 55.0 kg
Fixing the PDP to a wall or post with wires
Fix the eye bolts on the rear of the PDP to a firm
wall or post with strong wires.
<Reference values>
* Each wire should be have a 4 mm or larger
diameter and withstand 0.8 tons or higher load.
* Each wire should be anchored to the wall with
M10 x 45 mm or larger anchor bolts. Two wires
should be anchored.
zThe installation work must meet applicable laws and regulations
of the destination country/region.
zFixing with wire
Wire
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
Wire
Stationary stand Floor stand
zWhen installing the PDP on a wall, change the stand
hook at the center to the upper stand hook position.
*1
Line mark
Line mark
“H” mark Wall
zWall mounting
The installation work must be carried out only by
professionals.
The marks denote the center of the PDP.
zWall mounting dimensional tolerances
Base bracket pitch (the part marked with *1):
1,230 ±0.6 mm
zSurface level difference tolerance: 1.3 mm
Pitch tolerance: Left-right: ±1.0 Top-bottom: ±1.0 (mm)
zStand specifications (Model No.: TY-WK85PV12)
Dimensions: W 1,420 x H 1,071 x D 150 mm
Weight: Approx. 25.0 kg
Este manual sirve para los siguientes modelos
3
Otros manuales de Monitor de Panasonic
Panasonic
Panasonic TH-49LFV8U Manual de usuario
Panasonic
Panasonic TH-55VF2W Manual de usuario
Panasonic
Panasonic BTLH2550E - LCD VIDEO MONITOR Manual de usuario
Panasonic
Panasonic TH-42PHD8BK Manual de usuario
Panasonic
Panasonic WVBM1790 - B/W VIDEO MONITOR Manual de usuario
Panasonic
Panasonic CYVM5800U - 5.8" CLR MONITOR/DVD Manual de usuario
Panasonic
Panasonic TH-80LF50ER Manual de usuario
Panasonic
Panasonic WHA1 Series Manual de usuario
Panasonic
Panasonic TH-55SF2U Instrucciones de funcionamiento
Panasonic
Panasonic TH-42LF6W Manual de usuario
Panasonic
Panasonic TH-55LFV50W Manual de usuario
Panasonic
Panasonic TH-75CQ1W Manual de usuario
Panasonic
Panasonic 5054 Manual de usuario
Panasonic
Panasonic WVCK1420A - COLOR MONITOR Manual de usuario
Panasonic
Panasonic TENTATIVE TH-65VX300U Manual de usuario
Panasonic
Panasonic PANASYNC SM70 Manual de usuario
Panasonic
Panasonic PANASYNC TX-D7S36 Manual de usuario
Panasonic
Panasonic TX-1413FHE Manual de usuario
Panasonic
Panasonic TH-84EF1U Manual de usuario
Panasonic
Panasonic TH-65PF12EK Manual de usuario
