Panasonic TH-50PHD30BX Manual de usuario

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0000000000.html

Service Manual

TOP NEXT

ORDER NO. ITD0111013C2

High Definition Plasma Display

●TH-50PHD30BX/TH-50PHD30EX/TH-50PHW30BX/TH-50PHW30EX

GPH3D Chassis

Specifications

Power Source: AC220 - 240V 50/60Hz

Power Consumption: 530 W

3.0W (stand-by condition)

1.4W (Power off condition)

Plasma Display panel: Drive method AC type

50-inch, 16:9 aspect ratio

Contrast Ratio 3000:1

Brightness Capability (Panel only) 500 cd/ m2

(As a set) 300 cd/ m2

Screen size: 1106 mm (W)×622 mm (H)×1269 mm (diagonal)

No. of pixels

1,049,088 (1366 (W)×768 (H)) [4,098×768 dots]

Operating condition:

Temperature 0°C - 40°C

Humidity 20% - 80%

Applicable signals:

Color System NTSC, PAL, PAL60, SECAM, Modified NTSC

Scanning format 525i (480i), 625i (576i), 525p (480p), 750p (720p), 1125/60i, 50i, 24p, 24SF (1080/60i, 50i, 24p, 24SF).......SMPTE274M

PC signals XGA display

VGA, SVGA

SXGA, UXGA (compressed)

Horizontal scanning frequency 15.5 - 110kHz

Vertical scanning frequency 48 - 120Hz

Connection terminals:

(HIGH-DENSITY D-SUB15PIN) R,G,B/0.7 Vp-p (75-ohm)

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0000000000.html (1 of 2)09-03-28 11:09:44

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0000000000.html

HD, VD/1.0 - 5.0 Vp-p (high impedance)

AUDIO IN (M3.5 JACK) 0.5Vrms (high impedance)

SERIAL

EXTERNAL CONTROL TERMINAL (D-SUB9PIN) RS-232C COMPATIBLE

SPEAKERS (6Ω) 16W [8 W×8 W] (10% THD)

For TY-SP50PHD3W only

Dimensions (W×H×D): 1210 mm 724mm 8 mm

Weight (Mass) approx. 45.0 kg (main unit only)

approx. 49.6 kg (with speakers)

TOP NEXT

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0000000000.html (2 of 2)09-03-28 11:09:44

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0100000000x.html

1 Safety Precautions

TOP PREVIOUS NEXT

1.1 General Guidelines

1.2 Touch-Current Check

TOP PREVIOUS NEXT

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0100000000x.html09-03-28 11:09:52

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0101000000.html

1.1 General Guidelines

TOP PREVIOUS NEXT

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which

have been overheated or damaged by the short circuit.

2. After servicing, see to it that all the protective devices such as insulation barriers, insulation

papers shields are properly installed.

3. After servicing, make the following leakage current checks to prevent the customer from being

exposed to shock hazards.

TOP PREVIOUS NEXT

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0101000000.html09-03-28 11:09:54

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0102000000.html

1.2 Touch-Current Check

TOP PREVIOUS NEXT

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.

2. Connect a measuring network for touch currents between each exposed metallic part on the set

and a good earth ground such as a water pipe, as shown in Figure 1.

3. Use Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the

measuring network.

4. Check each exposed metallic part, and measure the voltage at each point.

5. Reserve the AC plug in the AC outlet and repeat each of the above measure.

6. The potential at any point (TOUGH CURRENT) expressed as voltage U1 and U2, does not

exceed the following values:

For a. c.: U1 = 35 V (peak) and U2 = 0.35 V (peak);

For d. c.: U1 = 1.0 V,

Note:

The limit value of U2 = 0.35 V (peak) for a. c. and U1 = 1.0 V for d. c. correspond to the values

0.7 mA (peak) a. c. and 2.0 mA d. c.

The limit value U1 = 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for

frequencies greater than 100 kHz.

7. In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and

the equipment should be repaired and rechecked before it is returned to the customer.

Figure 1. Measuring network for TOUCH CURRENTS

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0102000000.html (1 of 2)09-03-28 11:09:55

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0102000000.html

TOP PREVIOUS NEXT

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0102000000.html (2 of 2)09-03-28 11:09:55

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0200000000x.html

2 Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive

(ES) Devices

TOP PREVIOUS NEXT

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices.

Examples of typical ES devices are integrated circuits and some field-effect transistorsand semiconductor "chip" components. The following techniques should be

used to help reduce the incidence of component damage caused by electro static discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth

ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, whichshould be removed for potential shock reasons prior to

applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alminum foil, to prevent electrostatic

charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can generate electrical charge

sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are

packaged with leads electrically shorted together by conductive foam, alminum foil or comparableconductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly

into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing together of your clothes fabric

or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient todamage an ES device).

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0200000000x.html (1 of 2)09-03-28 11:09:56

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0200000000x.html

TOP PREVIOUS NEXT

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0200000000x.html (2 of 2)09-03-28 11:09:56

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0300000000x.html

3 PCB structure sheet of GPH3D chassis

TOP PREVIOUS NEXT

Board Part Number Remark

C1 TNPA1914 COMMON 1

C2 TNPA1915 COMMON 1

C3 TNPA1916 COMMON 1

C4 TNPA1917 COMMON 1

C5 TNPA1918 COMMON 1

C6 TNPA1919 COMMON 1

C7 TNPA1993 COMMON 1

C8 TNPA2277 COMMON 1

D TZTNP01KESE

F TXN/F10HAS COMMON 1

H3 TNPA1756AB COMMON 1

HX TZTNP02KESE COMMON 2

J TNPA2244N COMMON 2

P1 TXNP11KESE COMMON 1

P3 TNPA1907AC COMMON 1

P4 TNPA1908 COMMON 1

P5 TNPA1909AC COMMON 1

P6 TNPA1910AC COMMON 1

P7 TNPA1911AC COMMON 1

P8 TNPA1912AC COMMON 1

P9 TNPA1906AC COMMON 1

S1 TNPA1784 COMMON 1

SC TNPA1922 COMMON 1

SD TNPA1921 COMMON 1

SS TNPA1923 COMMON 1

SS2 TNPA1924 COMMON 1

SS3 TNPA1925 COMMON 1

SU TNPA1920 COMMON 1

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0300000000x.html (1 of 2)09-03-28 11:09:58

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0300000000x.html

T12 TNPA2373

V1 TNPA2282AB COMMON 2

Note

COMMON 1: COMMON parts with model TH-50PHW3, 50PHD3 series.

COMMON 2: COMMON parts with model TH-42PW4, 42PWD4 series.

TOP PREVIOUS NEXT

file:///C|/Documents and Settings/lopez/Pulpit/TH-50PHW30/TH-50PHW30/ALL/TH-50PHD30BX/SVC/s0300000000x.html (2 of 2)09-03-28 11:09:58

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Monitor de Panasonic

Panasonic

Panasonic TH42PX20U - 42" HDTV PLASMA DISPLAY Manual técnico

Panasonic

Panasonic Viera TH-42PWD4 Manual de usuario

Panasonic

Panasonic C1381 Manual de usuario

Panasonic

Panasonic CFVDL01W - LCD MONITOR Manual de usuario

Panasonic

Panasonic SuperFlat CT-F3394 Manual de usuario

Panasonic

Panasonic TH-42PHW6EX Manual de usuario

Panasonic

Panasonic TH-103PB1E Manual de usuario

Panasonic

Panasonic TH-47LFX6U Manual de usuario

Panasonic

Panasonic TH-65PF20U Manual de usuario

Panasonic

Panasonic TH-58PF12UK Manual de usuario

Panasonic

Panasonic PT-43LC14K Manual de usuario

Panasonic

Panasonic WVBM140 - B/W MONITOR Manual de usuario

Panasonic

Panasonic BTLH80W - 7.9" MONITOR Manual de usuario

Panasonic

Panasonic CY-VM1500 Manual de usuario

Panasonic

Panasonic TH-55LFV50U Manual de usuario

Panasonic

Panasonic TH-85PF12U Manual de usuario

Panasonic

Panasonic TH-50PHD8BK Manual de usuario

Panasonic

Panasonic BTLH1760P - LCD VIDEO MONITOR Manual de usuario

Panasonic

Panasonic TH61PHW6 - 61" PLASMA DISPLAY Manual de usuario

Panasonic

Panasonic TH-65EF1U Instrucciones de funcionamiento

Panasonic

Panasonic CY-VMC7000U Manual de usuario

Panasonic

Panasonic TH-42PH12L Manual de usuario

Panasonic

Panasonic TH-65PF20W Manual de usuario

Panasonic

Panasonic PT-60LCX63 - 60" Rear Projection TV Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación

LG M1950D-PZ Manual de usuario