Panasonic PT-AH1000E Manual de usuario
LCD Projector
Thank you for purchasing this Panasonic product.
■ Before operating this product, please read the instructions (Basic Guide / Functional Manual) carefully and
save this manual for future use.
■ Please ensure you read the “Read this rst!” (pages 6to 12) carefully prior to use.
Operating Instructions
Functional Manual
ENGLISH
Model No. PT-AH1000E
TQBJ0405
2 - ENGLISH
WARNING:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting
to computers or peripheral devices. Any unauthorized changes or modications to this
equipment will void the users authority to operate.
ENGLISH - 3
Features of the ProjectorFeatures of the Projector
This projector is equipped with
technology to automatically adjust
the image according to the lighting
of the projection environment
(brightness, color).
A newly developed high luminance
lamp and an optical system have
been introduced to facilitate the joy
of viewing in a bright living room.
This projector is equipped with an
exclusive mode for enjoying games
and sports content at high image
quality levels.
Harmonization with
projection environment
Improved brightness
Wide range of picture modes
Quick StepsQuick Steps
See the relevant page for details.
1. Set up your projector
(
page 20)
2. Connect the projector to
other devices
(
page 25)
3. Connect the power cord
(
page 27)
4. Switch on the projector
(
page 28)
5. Select the input signal
(
page 30)
6. Adjust the image
(
page 30)
4 -
ENGLISH
Important
Information Introduction Getting Started Basic Operation Settings Maintenance Appendix
Contents Be sure to read “Read this rst!”. (pages 6to 12)
Important Information
Read this rst! .....................................................6
Precautions for use ......................................... 13
Cautions when transporting..........................................13
Cautions when installing...............................................13
Cautions on use............................................................15
About disposal...............................................................15
Accessories...................................................................16
Optional accessories ....................................................16
Introduction
About your projector ....................................... 17
Remote control..............................................................17
Projector body...............................................................18
Getting Started
Setting up .......................................................... 20
Projection method.........................................................20
Parts for ceiling mount (optional)..................................20
Projection related ..........................................................21
Front adjustable feet and throwing angle ....................22
Lens shift and positioning.............................................23
Connections...................................................... 25
Before connecting to the projector ...............................25
Connecting example: COMPONENT IN/
S-VIDEO IN/VIDEO IN .................................................25
Connecting example: HDMI IN/COMPUTER IN......... 26
Basic Operation
Switching the projector on/off ....................... 27
Power cord ....................................................................27
Power indicator .............................................................27
Switching on the projector ............................................28
Switching off the power.................................................29
Projecting an image......................................... 30
Selecting the input signal..............................................30
Adjusting the image ......................................................30
Remote control operation............................... 31
Illuminating button lights ...............................................31
Selecting the picture mode...........................................31
Adjusting the picture .....................................................31
Loading a saved setting................................................32
Displaying the [VIERA LINK MENU] menu .................32
Displaying the waveform monitor.................................32
Resetting to the default settings...................................32
Submenu.......................................................................33
Switching the input signal.............................................33
Using the <FUNCTION> button .........................................33
Displaying the [ECO MANAGEMENT] menu..............33
Settings
Menu navigation............................................... 34
Navigating through the menu.......................................34
Menu list ........................................................................35
[PICTURE] menu .............................................. 37
[PICTURE MODE]........................................................37
[CONTRAST] ................................................................37
[BRIGHTNESS] ............................................................37
[COLOUR].....................................................................37
[TINT].............................................................................37
[COLOUR TEMPERATURE] .......................................38
[SHARPNESS]..............................................................38
[DYNAMIC IRIS] ...........................................................38
[LIGHT HARMONIZER] ...............................................38
[WAVEFORM MONITOR] ............................................39
[SPLIT ADJUST] ...........................................................41
[ADVANCED MENU]....................................................42
[PICTURE MEMORY] ..................................................53
SIGNAL MODE.............................................................54
[POSITION] menu............................................. 55
[H-POSITION]...............................................................55
[V-POSITION] ...............................................................55
[DOT CLOCK]...............................................................55
[CLOCK PHASE]..........................................................55
[ASPECT]......................................................................56
[WSS] ............................................................................58
[OVER SCAN]...............................................................58
[KEYSTONE] ................................................................58
ENGLISH
- 5
Important
Information
IntroductionGetting StartedBasic OperationSettingsMaintenanceAppendix
Contents
[AUTO SETUP].............................................................58
[SCREEN AREA MEMORY] ........................................59
[OPTION] menu ................................................ 63
[ON-SCREEN DISPLAY]..............................................63
[BACK COLOUR] .........................................................63
[STARTUP LOGO]........................................................64
[AUTO SEARCH]..........................................................64
[HDMI SIGNAL LEVEL]................................................64
[FRAME RESPONSE]..................................................64
[PROJECTION METHOD]...........................................64
[TRIGGER 1/2 SETTING] ............................................65
[HIGH ALTITUDE MODE] ............................................66
[LAMP POWER] ...........................................................66
[ECO MANAGEMENT] ................................................67
[FUNCTION BUTTON].................................................68
[VIERA LINK SETTINGS].............................................68
[OTHER FUNCTIONS].................................................70
[TEST PATTERN] .........................................................70
[LAMP RUNTIME] ........................................................70
Maintenance
TEMP and LAMP Indicators............................ 71
Managing the indicated problems................................71
Care and replacement ..................................... 73
Before cleaning the projector /
replacing components ..................................................73
Cleaning the projector...................................................73
Component replacement..............................................75
Troubleshooting ............................................... 80
Ceiling mount bracket safeguards................ 81
Appendix
Using VIERA Link............................................. 82
Summary of VIERA Link features ................................82
VIERA Link “HDAVI Control” ........................................83
Technical information...................................... 86
List of compatible signals .............................................86
Serial terminal ...............................................................87
Specications ................................................... 90
Dimensions ...................................................................92
Index................................................................... 93
Read this rst!
6 -
ENGLISH
Important
Information
Read this rst!
WARNING: THIS APPARATUS MUST BE EARTHED.
WARNING: To prevent damage which may result in re or shock hazard, do not expose this appliance to rain
or moisture.
Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator
position is equal or less than 70 dB (A) according to ISO 7779.
WARNING:
1. Remove the plug from the mains socket when this unit is not in use for a prolonged period of time.
2. To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to
qualied service personnel.
3. Do not remove the earthing pin on the mains plug. This apparatus is equipped with a three prong
earthingtype mains plug. This plug will only t an earthing-type mains socket. This is a safety feature. If you
are unable to insert the plug into the mains socket, contact an electrician. Do not defeat the purpose of the
earthing plug.
CAUTION: To assure continued compliance, follow the attached installation instructions, which includes using
the provided power cord and shielded interface cables when connecting to computer or peripheral
device. If you use serial port to connect PC for external control of projector, you must use optional
RS-232C serial interface cable with ferrite core. Any unauthorized changes or modications to
this equipment will void the user’s authority to operate.
EEE Yönetmeliğine Uygundur.
EEE Complies with Directive of Turkey.
Read this rst!
ENGLISH
- 7
Important
Information
IMPORTANT: THE MOULDED PLUG (U.K. only)
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse
is tted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating
of 13 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is retted when the fuse is replaced. If you
lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover
can be purchased from an Authorised Service Center.
If the tted moulded plug is unsuitable for the mains socket in your home, then the fuse should be
removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the
cut off plug is inserted into any 13 amp socket.
If a new plug is to be tted, please observe the wiring code as shown below.
If in any doubt, please consult a qualied electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Green - and - Yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows.
The wire which is coloured GREEN - AND - YELLOW must be connected to the terminal in the
plug which is marked with the letter E or by the Earth symbol or coloured GREEN or GREEN -
AND - YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is
marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is
marked with the letter L or coloured RED.
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.
13A250V BS1363/A
HE-8
N
ASA
L
Read this rst!
8 -
ENGLISH
Important
Information
WARNING:
POWER
The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily
accessible when problems occur. If the following problems occur, cut off the power supply
immediately.
Continued use of the projector in these conditions will result in re or electric shock.
If foreign objects or water get inside the projector, cut off the power supply.
z
If the projector is dropped or the cabinet is broken, cut off the power supply.
z
If you notice smoke, strange smells or noise coming from the projector, cut off the power supply.
z
Please contact an Authorized Service Center for repairs, and do not attempt to repair the projector yourself.
During a thunderstorm, do not touch the projector or the cable.
Electric shocks can result.
Do not do anything that might damage the power cord or the power plug.
If the power cord is used while damaged, electric shocks, short-circuits or re will result.
Do not damage the power cord, make any modications to it, place it near any hot objects, bend it
z
excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.
Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.
Completely insert the power plug into the wall outlet and the power connector into the projector
terminal.
If the plug is not inserted correctly, electric shocks or overheating may occur and re will result.
Do not use plugs which are damaged or wall outlets which are coming loose from the wall.
z
Do not use anything other than the provided power cord.
Failure to observe this will result in electric shocks or re.
Clean the power plug regularly to prevent it from becoming covered in dust.
Failure to observe this will cause a re.
If dust builds up on the power plug, the resulting humidity can damage the insulation.
z
If not using the projector for an extended period of time, pull the power plug out from the wall outlet.
z
Pull the power plug out from the wall outlet and wipe it with a dry cloth regularly.
Do not handle the power plug and power connector with wet hands.
Failure to observe this will result in electric shocks.
Do not overload the wall outlet.
If the power supply is overloaded (ex., by using too many adapters), overheating may occur and re will result.
Read this rst!
ENGLISH
- 9
Important
Information
WARNING:
ON USE/INSTALLATION
Do not place the projector on soft materials such as carpets or sponge mats.
Doing so will cause the projector to overheat, which can cause burns, re or damage to the projector.
Do not set up the projector in humid or dusty places or in places where the projector may come into
contact with oily smoke or steam, ex. a bathroom.
Using the projector under such conditions will result in re, electric shocks or deterioration of components.
Deterioration of components (such as ceiling mount brackets) may cause the projector which is mounted on
the ceiling to fall down.
Do not install this projector in a place which is not strong enough to take the full weight of the
projector or on top of a surface which is sloped or unstable.
Failure to observe this will cause projector to fall down or tip over the projector, and severe injury or damage
could result.
Do not cover the air inlet port or the air outlet port.
Doing so will cause the projector to overheat, which can cause re or damage to the projector.
Do not place the projector in narrow, badly ventilated places such as closets or bookshelves.
z
Do not place the projector on cloth or papers, as these materials could be drawn into the air inlet port.
z
Do not place your hands or other objects close to the air outlet port.
Doing so will cause burns or damage your hands or other objects.
Heated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot
z
withstand heat close to this port.
Do not cover the air intake/exhaust ports or place anything within 100 mm (4") of them.
Doing so will cause the projector to overheat, which can cause re or damage to the projector.
Do not look and place your skin into the lights emitted from the lens while the projector is being used.
Doing so can cause burns or loss of sight.
Strong light is emitted from the projector’s lens. Do not look or place your hands directly into this light.
z
Be especially careful not to let young children look into the lens. In addition, turn off the main power when
z
you are away from the projector.
Never attempt to remodel or disassemble the projector.
High voltages can cause re or electric shocks.
For any inspection, adjustment and repair work, please contact an Authorized Service Center.
z
Do not project an image with the lens cover attached.
Doing so can cause re.
Do not allow metal objects, ammable objects, or liquids to enter inside of the projector. Do not allow
the projector to get wet.
Doing so may cause short circuits or overheating, and result in re, electric shock, or malfunction of the
projector.
Do not place containers of liquid or metal objects near the projector.
z
If liquid enters inside of the projector, consult your dealer.
z
Particular attention must be paid to children.
z
Use the ceiling mount bracket specied by Panasonic.
Defects in the ceiling mount bracket will result in falling accidents.
Attach the supplied safety cable to the ceiling mount bracket to prevent the projector from falling down.
z
Installation work (such as ceiling mount bracket) should only be carried out by a qualied technician.
If installation is not carried out and secured correctly it can cause injury or accidents, such as electric shocks.
Do not use anything other than an authorized ceiling mount bracket.
z
Be sure to use the provided accessory wire with an eye bolt as an extra safety measure to prevent the
z
projector from falling down. (Install in a different location to the ceiling mount bracket)
Read this rst!
10 -
ENGLISH
Important
Information
WARNING:
ACCESSORIES
Do not use or handle the batteries improperly, and refer to the following.
Failure to observe this will cause burns, batteries to leak, overheat, explode or catch re.
Do not use unspecied batteries.
z
Do not disassemble dry cell batteries.
z
Do not heat the batteries or place them into water or re.
z
Do not allow the + and - terminals of the batteries to come into contact with metallic objects such as
z
necklaces or hairpins.
Do not store batteries together with metallic objects.
z
Store the batteries in a plastic bag and keep them away from metallic objects.
z
Make sure the polarities (+ and -) are correct when inserting the batteries.
z
Do not use a new battery together with an old battery or mix different types of batteries.
z
Do not use batteries with the outer cover peeling away or removed.
z
If the battery uid leaks, do not touch it with bare hands, and take the following measures if necessary.
Battery uid on your skin or clothing could result in skin inammation or injury.
z
Rinse with clean water and seek medical advice immediately.
Battery uid coming in contact with your eyes could result in loss of sight.
z
In this case, do not rub your eyes. Rinse with clean water and seek medical advice immediately.
Do not disassemble the lamp unit.
If the lamp breaks, it could cause injury.
Lamp replacement
The lamp has high internal pressure. If improperly handled, an explosion and severe injury or accidents will
result.
The lamp can easily explode if struck against hard objects or dropped.
z
Before replacing the lamp, be sure to disconnect the power plug from the wall outlet.
z
Electric shocks or explosions can result if this is not done.
When replacing the lamp, turn the power off and allow the lamp to cool for at least one hour before
z
handling it otherwise it can cause burns.
Do not allow infants or pets to touch the remote control.
Keep the remote control out of the reach of infants and pets after using it.
z
Do not use the supplied power cord with devices other than this projector.
Using the supplied power cord with devices other than this projector may cause short circuits or
z
overheating, and result in electric shock or re.
Remove the depleted batteries from the remote control promptly.
Leaving them in the unit may result in uid leakage, overheating, or explosion of the batteries.
z
Otros manuales para PT-AH1000E
1
Tabla de contenidos
Otros manuales de Proyector LCD de Panasonic
Panasonic
Panasonic PT-LX22U Manual de usuario
Panasonic
Panasonic PT-LX22E Manual de usuario
Panasonic
Panasonic PT-TW231RE Manual de usuario
Panasonic
Panasonic PT-TW340 Manual de usuario
Panasonic
Panasonic PT-FW100NTE Manual de usuario
Panasonic
Panasonic PT-FW430E Manual de usuario
Panasonic
Panasonic PT_AT6000E Manual de usuario
