Panasonic SR-TML500 Manual de usuario

Order No. PAPTH140402CE

Service Manual

Multi-Cooker

SR-TML500

SR-TML510

SR-TMS520

distribution is a violation of law.

There are special components used in this equipment which are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Diagrams, Exploded Views and Replacement Parts List. It is essential that

these critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do

not modify the original design without permission of manufacturer.

IMPORTANT SAFETY NOTICE

The service information is designed for experienced repair technicians only and is not designed for use by the general

public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting

to service a product. Products powered by electricity should be serviced or repaired only by experienced professional

technicians. Any attempt to service or repair the product or products dealt within this service information by anyone

else could result in serious injury or death.

WARNING

Destination

Russia / Ukraine / Kazakhstan

Product Colour

Black (BO)

Silver (HS)

Dark Silver (HL)

- 2 -

CONTENT

Page

6 - 7

16 - 17

1. Specification

2. Schematic Diagram

2.1 Wiring Diagram

2.2 Circuit Diagram

3. Troubleshooting Guide

3.1 Table 1

3.2 Table 2

4. Testing Procedure

4.1 Bubbling Test

4.2 Evaporation Test

4.3 Heat reserving Test

5. Disassembly

5.1 Hinge cover removal

5.2 Inner enclosure and upper frame removal

5.3 Control unit A

5.4 Cast heater and Thermostat Ass’y

5.5 Side heater

6. Parts Exploded View and Replacement Parts List

6.1 Parts Exploded View : Body

6.2 Parts Exploded View : Packing

6.3 Replacement Parts List

SR-TML500 / SR-TML510 / SR-TMS520

- 3 -

1. SPECIFICATION

MODEL

Countries

Power Supply

* For power cord replacement and product repairing, please contact the authorized service center of Panasonic.

* The design and specifications are subjected to change without prior notice.

SR-TML500 SR-TML510

Russia, Ukraine, Kazakhstan

220V / 50Hz / SH-3

Colour Name SilverDark Silver Black

HL BO

Measuring cup, Yogurt cup,

Steam basket assy,

Pan lid, Porridge scoop

Colour Code HS

Body Material Steel / Pre-coating

Pan Material Aluminium / Non stick coating

Power Consumption Cooking

Warming

Cooking Capacity Milk Porridge

Pilaf

Buckwheat

Yogurt

Baking

Fry

Stew / Soup / Compote

Holodetz / Stuffed /

Confiteur

670W

108W

1 ~ 2 cups

Warming Capacity

2 ~ 3 cups

2 ~ 8 cups

600 g.

900 g.

1.2 Kg.

4.0 L

Steam / Permeni

Plain Rice

4.0 L

Re-heat 1.0 L

Express 4.0 L

3 ~ 10 cups

Cooked rice warming Temperature 71°C ~ 79°C

Thermal fuse Specification 172°C 250V / 10A

Keep Warm (in Buckwheat function) 12 Hours

Weight (Approx.) 3.3 Kgs.

Power Cord (Approx.) 1.0 m.

Accessories Measuring cup, Steam basket assy

TheProduct Dimension

(Width x Depth x Height)

276 x 275 x 274 (mm)

Temperature Detector Sensor thermistor

SR-TMS520

SR-TML500 / SR-TML510 / SR-TMS520

- 4 -

2. SCHEMATIC DIAGRAM

2.1 Wiring Diagram

Glass tape

size 40 X 85 mm2

Inlet

Shall be

closely covered with

tube to the bottom

Body earth lead wire (Green)

PCB lead wire A (White)

Thermal fuse lead wire B (Orange)

The glass tape affixes it from a

top and bottom direction, and

make it sealing up structure.

Impossible power do not be

added to a terminal joint.

5mm, or more

(Tape sealing area)

PCB lead wire B (Black)

Glass tape shall be

wraped around PCB

Thermistor lead wire (Red)

(Twisting 1 time)

Thermostat earth lead wire (Green)

Detail 2 : 1

Thermistor lead wire (Red)

Side heater lead wire A (Blue)

- Twisted vinyly tie 2 times.

- White, blue and black lead wire shall

not over lap PCB base boss.

- This blue wire shall be align in this portion.

Side heater lead wire D (White)

Side heater lead wire C (White)

Side heater lead wire B (Blue)

Terminal shall not be higher

than head of sems screw.

Side heater lead wire C (Black)

PCB lead wireC (Red)

Side heater lead wire D (Red)

Hinge earth lead wire (Green)

Tapping screw for body earth lead wire

Should be above Thermal fuse

lead wire A and then gose below

terminal of side heater lead wire D

Stamping earth

mark on PF.

5mm (around)

(Ø8)

- Twisted vinyly tie 2 times.

- All lead wire must not touch Cast heater terminal.

Thermal fuse

lead wire A (Black)

Thermostat earth lead wire (Green)

After twisted 2 times,

wind down this direction.

(Shall not touch Cast heater)

Vinyly tie

Lead wire

The clearance distance between terminal

& sems screw to other dead metal part

(Protecting frame, Cast heater pipe)

Should minimum 3.6 mm. (Any direction)

After inspection, screw head must be

mark with marker.

(Note) 1. Tightening torque of tapping screw for body earth lead wire and

sems screw for internal wiring : 60 ~ 120N - m

2. Each lead wire shall not contacting with sharp edges, moving parts,

high temperation portion.

3. All lead wire must not be hurt during assembly when apply 2N force.

Technical

Regulation

WARNING

Body earth lead wire

(Green)

Thermal fuse lead wire B (Orange)

PCB lead wire A (White)

SR-TML500 / SR-TML510 / SR-TMS520

- 5 -

SR-TML500 / SR-TML510 / SR-TMS520

2.2 Circuit Diagram

- 6 -

3. TROUBLESHOOTING GUIDE

3.1 Table 1

When receiving a rice boiler to be repaired, be sure to check that the main body is completely provide with the inner pan

and the inner lid, ask the condition (phenomenon) of the trouble in detail. Before troubleshooting single parts, be sure to

disconnect the power supply plug from the receptacle.

Condition

Rice boiling section

Plane rice.

• Rice is not boiling.

(The indicating lamp

does not come on)

• Rice is not boiling.

(The indicating lamp

is lit)

Troubleshooting Remedy

Is the power cord conductive? • Replace the cord.

• Make sure insert therminal is

fasten.

• Replace the P.C.B. complete.

• Replace the cast heater.

• Replace the center thermostat.

• Replace the inner pan or the

cast heater.

• Seeing at Table 2

• Explain the proper operation.

• Isolate the cause which melt

the thermal fuse, correct

the cause and

• Earlier cut off.

• Poor boiling up.

• Too hard

• Too soft

• Insufficient boiling

• Immediately after the switch is turned

off, open the cap.

• Rice is excessive or insufficient.

• Rice has not been scooped and mixed

well.

• Water is excessive or insufficient.

• The switch is turned off once during

boiling.

Is the pan bottom properly contacted with

the cast heater?

Yes

Is the thermal fuse conductive?

Yes

Is the therminal conductive?

Yes

Are the parts on the P.C.B. mistake?

Improper operation

Yes

Is the cast heater conductive?

Yes

Are the parts on the P.C.B. mistake?

(Check with the bubbling test).

Does the center thermostat operate

properly?

Yes

(Check with the operation test).

Yes

SR-TML500 / SR-TML510 / SR-TMS520

- 7 -

Condition Troubleshooting Remedy

• Replace the center thermostat.

• Seeing at Table 2.

• Explain the proper operation.

• Excessive burning.

(More than light brown)

• The voltage is lower than specified.

• Rice is not washed sufficiently

• Water is excessive.

(Bran remains still)

• The pan bottom is conditioned to

generate burning easily.

Are the parts on the P.C.B. mistake?

Improper operation

Yes

Does the center thermostat operate

properly?

Yes

(Check with the evaporation test).

• To join it with CN5.

• Display of “Slow Cook”

and “Rice Cook/Steam”

are flashing light.

Check the sensor lead wire is connect

completely with control unit board. No

• Take off and join it with CN5

again.

Yes

• Check the connector of wiring.

• Display of “Start” and

“Timer” are flashing

light.

Is the relay operation ON/OFF alternately

after flashing light occur? No

• Replace the control unit

complete.

Yes

SR-TML500 / SR-TML510 / SR-TMS520

- 8 -

3.2 Table 2

Condition

• Rice is not boiling.

(The indicating lamp

does not come on)

• Rice is not boiling.

• The thermal fuse is

blown off.

• Earlier cut off.

• Poor boiling up.

• Excessive burning.

(The indicating lamp

is lit)

• Heat is not reserved.

(The indicating lamp

does not come on)

• Heat is not reserved.

(The indicating lamp

is lit)

Troubleshooting Remedy

Is the transformer operating?

• Replace the P.C.B. complete.

• Replace the transformer.

• Replace the relay.

• Replace the transformer.

• Replace the relay.

Is the relay operation? No

Is the relay cut off?

Is the relay operation?

Yes

• Replace the P.C.B. complete.

Yes

• Replace the P.C.B. complete.

Yes

• Replace the P.C.B. complete.

Yes

• Replace the P.C.B. complete.

Yes

• Replace the P.C.B. complete.

Yes

Is the relay operation? No

Is the transformer operating? No

• Replace the transformer.

• Replace the P.C.B. complete.

Yes

Is the trial operating? No

SR-TML500 / SR-TML510 / SR-TMS520

- 9 -

4. TESTING PROCEDURE

4.1 Bubbling test

Input the pan in the main body, lightly rotate the pan clockwise and counter clockwise to settle the pan on the

heating plate properly.

1. Fill water until center area of the pan bottom is dipped and close the lid. Then turn on the boiling switch.

4.2 Evaporation test

1. Check that bubbling is proper, open the lid and place a weight.

2. Fully cover 2 to 3 sheet of tissue paper (gauze is also applicable) on the pan bottom and continuously

flow electric current.

Note : To prevent plastic parts from deformation caused by steam, be sure to open the lid fully.

Note : To prevent tissue paper from floating because of bubbling, previously hole the paper.

3. Water on the pan bottom is completely evaporated to be empty. This timing is an follows :

Within 1 minute before the boiling switch is turned off.

Within 1 minute after the boiling switch is turned off.

Place a weight so that its gravity center may be aligned at the center

2. When it beings boiling to produce steam. Remove the lid immediately check the bubbling condition on

the pan bottom.

3. As show in the figture.

If it is improper, it may result from the insufficient contact between the pan bottom and heating plate.

Check the pan bottom and the heating plate for foreign material remainder. Clean off the foreign materials

or replace the parts.

Bubbles generate through out the circumference of the pan bottom...............................................Proper

Bubbles does not generate on more than one quater part of the pan bottom circumference..........Improper

Bubbling

SR-TML500 / SR-TML510 / SR-TMS520

5 cm

40 cm

- 10 -

4.3 Heat reserving test

The above conditions are proper.

1. Put approx. 1 liter of water and the thermometer [ repairing tool (mercury thermometer ASN-150H) ]

in the pan, close the lid and turn on the boiling switch.

2. When the beings boiling to generate steam turn off the boiling switch.

Within 69°C - 77°C .....................................Proper

If outside 69°C - 77°C, check triac mounting for irregularity, if it is proper, replace warming heater.

3. Add water or keep the lid opened until the reading of the thermometer falls to approx. 70°C.

4. When it becomes approx. 70°C, close the lid. After the warming heater is activated for 1 hour or more,

check the heat reserving temperature.

Top view of pan

Holes on the

tissue paper

Pan flange

Tissue paper

Mercury thermometer

Urethane foam blocks

Mercury thermometer

Inner Pan

SR-TML500 / SR-TML510 / SR-TMS520

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Electrodoméstico de cocina de Panasonic

Panasonic

Panasonic SR-TMH10 Manual de usuario

Panasonic

Panasonic NC-SSA400 Manual de usuario

Panasonic

Panasonic SR-FC108 Manual de usuario

Panasonic

Panasonic NC-HU401P Manual de usuario

Panasonic

Panasonic SD-MA18N Manual de usuario

Panasonic

Panasonic SR-ZE185 Manual de usuario

Panasonic

Panasonic NC-HU301P Manual de usuario

Panasonic

Panasonic MJ66PR - JUICE EXTRACTOR Manual de usuario

Panasonic

Panasonic EH-SA60 Manual de usuario

Panasonic

Panasonic MX-SS40 Manual de usuario

Panasonic

Panasonic SR-TMJ181 Manual de usuario

Panasonic

Panasonic SR-PAA100 Manual de usuario

Panasonic

Panasonic NC-HU301P Manual de usuario

Panasonic

Panasonic NEDF20G - COMMERCIAL MICROVEN Manual de usuario

Panasonic

Panasonic NC-EG4000 Manual de usuario

Panasonic

Panasonic MX-AC400 Manual de usuario

Panasonic

Panasonic SR-SAT18 Manual de usuario

Panasonic

Panasonic MX-AC400 Manual de usuario

Panasonic

Panasonic SD-MA18N Manual de usuario

Panasonic

Panasonic EH-SA31 Manual de usuario

Panasonic

Panasonic NC-EH22PC Manual de usuario

Panasonic

Panasonic NC-TWS30 Manual de usuario

Panasonic

Panasonic EH-SA31VP Manual de usuario

Panasonic

Panasonic SR-TMH501 Manual de usuario

Manuales populares de Electrodoméstico de cocina de otras marcas

Tayama

Tayama TYG-35AF Manual de usuario

AEG

AEG 43172V-MN Manual de usuario

REBER

REBER Professional 40 Guía del usuario

North American

North American BB12482G / TR-F-04-B-NCT-1 Manual de usuario

Presto

Presto fountain popper Manual de usuario

Westmark

Westmark 1035 2260 Manual de usuario

Zanussi

Zanussi ZCG64396XA Manual de usuario

HOFFEN

HOFFEN SM-9302M Manual de usuario

Philips

Philips HD3133 Manual de usuario

Ronco

Ronco Beef Jerky Manual de usuario

Hendi

Hendi 470411 Manual de usuario

Livoo

Livoo MEN386 Manual de usuario

Vogue

Vogue D446 Manual de usuario

croydon

croydon WR-10313-700 Manual de usuario

ADE

ADE AUTOMATIC-L Manual de usuario

Chefman

Chefman RJ43-SQ Series Manual de usuario

Vacmaster

Vacmaster VP680 Manual de usuario

Jetmaster

Jetmaster 900HG Manual de usuario