Panasonic EY76A1 Manual de usuario

© Panasonic Corporation 2019. All rights reserved.

Unauthorized copying and distribution is a violation

of law.

ORDER NO. PTD1909E04CE

Cordless Impact Driver

Model No. EY76A1

Europe

TABLE OF CONTENTS

PAGE PAGE

1 Warning -------------------------------------------------------------- 2

2 Specifications ----------------------------------------------------- 2

3 Troubleshooting Guide ----------------------------------------- 3

4 Disassembly and Assembly Instructions ---------------- 6

5 Exploded View and Replacement Parts List -----------10

2

1Warning

Caution:

• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70 °F (30 - 40 °C) higher.

Please use a soldering iron with temperature control and adjust it to 750 ± 20 °F (400 ± 10 °C). In case of using high temperature

soldering iron, please be careful not to heat too long.

• Pb free solder will tend to splash when heated too high (about 1100°F / 600 °C).

2 Specifications

3

3 Troubleshooting Guide

3.1. Troubleshooting Guide

4

5

3.2. Trial Operation (after checking Troubleshooting Guide).

3.2.1. Assembly

• Confirm if there is no gap between housing A and B by pinching lead wires.

• There is no dust or deformation on battery terminals.

• Confirm all screws are tightened firmly.

• Confirm if there is no dirt when repairing.

3.2.2. Operation

• Check whether the tool operates properly in both the forward and reveres directions.

• Check whether the LED lights ON.

• Check whether the tool speed increases continuously as the trigger is gradually engaged.

• Check whether the tool speed is normal after repair and reassembly.

Hard mode: 0 to 2800 rpm at 14.4V/18V.

Medium mode: 0 to 1450 rpm at 14.4V/18V.

Soft mode: 0 to 950 rpm at 14.4V/18V.

• Check whether the remaining battery power indicator lamp lights up or flashes when the Battery level button is pressed.

6

4 Disassembly and Assembly Instructions

* To reduce the risk of injury, always remove battery pack before removing/installing the tool.

* To assemble the tool, start with 4-4 and proceed to 4-1

4.1. How to remove the Housing.

4.2. How to remove the Driving assembly.

1. After removing the plate hook, remove 9 housing screws.

2. Then open the housing B.

3. Remove the interior parts.

4. Remove the interior components from the housing A.

Note: (when assembling)

Route LED lead wires and motor lead wire between the ribs on housing

A like the figure.

Hold the motor assembly, remove the fixation cover assembly and asso-

ciated parts together from the motor assembly.

7

4.3. How to remove the Fixation cover assembly and Driving shaft assembly.

Note: (when assembling)

1. Remove the protector.

2. Remove the interior components from the fixation cover

assembly.

8

4.4. How to remove the Switch assembly, LED harness assembly and

Battery terminal.

Note: (when assembling)

The connect cover cannot be reused after being repaired.

NOTE:(When attaching the connectors/switch).

Apply grease (Permalub) to the indicated by the shaded area.

1. Remove the connector(6-pin/2-pin) covers.

2. Disconnect the connecters or lead wires in order to (1) to (4).

Note:

Exercise care not to bend the terminal fitting.

9

4.5. Wiring and Assembly Points.

Model No. : EY76A1 Exploded View

5 Exploded View and Replacement Parts List

Otros manuales para EY76A1

1

Tabla de contenidos

Otros manuales de Atornillador de impacto de Panasonic

Panasonic

Panasonic EY75A7 Manual de usuario

Panasonic

Panasonic EY7201-X8 Manual de usuario

Panasonic

Panasonic EY7530 Manual de usuario

Panasonic

Panasonic EY75A1 Manual de usuario

Panasonic

Panasonic EYFPA1J Manual de usuario

Panasonic

Panasonic EY75A1 Manual de usuario

Panasonic

Panasonic EY7206 - 12V IMPACT DRIVER Manual de usuario

Panasonic

Panasonic EY76A1 Manual de usuario

Panasonic

Panasonic EYFLA1A - DRILL - MULTI LANGUAGE Manual de usuario

Panasonic

Panasonic EY7552 Manual de usuario

Panasonic

Panasonic EY75A2 Manual de usuario

Panasonic

Panasonic EY75A1 Manual de usuario

Panasonic

Panasonic EY7206 - 12V IMPACT DRIVER Manual de usuario

Panasonic

Panasonic EYFLA4A Manual de usuario

Panasonic

Panasonic EYFLA3J - DRILL - MULTI LANGUAGE Manual de usuario

Panasonic

Panasonic EY7202 - 12V IMPACT DRIVER Manual de usuario

Panasonic

Panasonic EY7206GQW Manual de usuario

Panasonic

Panasonic EY7546 Manual de usuario

Panasonic

Panasonic EY7541 - CORDLESS IMPACT WRENCH Manual de usuario

Panasonic

Panasonic EY7541 - CORDLESS IMPACT WRENCH Manual de usuario

Panasonic

Panasonic EY7542 - CORDLESS IMPACT WRENCH Manual de usuario

Panasonic

Panasonic EY75A7 Manual de usuario

Panasonic

Panasonic EY7201-U1 Manual de usuario

Panasonic

Panasonic EY7546LR2S Manual de usuario

Manuales populares de Atornillador de impacto de otras marcas

stayer

stayer IW500D Manual de usuario

Makita

Makita DTD152 Manual de usuario

Milwaukee

Milwaukee M12 FID Manual de usuario

Grizzly

Grizzly H6140 Manual de usuario

Makita

Makita BTW450 Manual de usuario

Ozito

Ozito LID-3000 Manual de usuario

Astro Pneumatic Tool

Astro Pneumatic Tool 1812 Manual de usuario

Greenlee

Greenlee HW3 Manual de usuario

Sthor

Sthor 57091 Manual de usuario

Makita

Makita DTD145 Manual de usuario

Hilti

Hilti SIW 2-A12 Manual de usuario

Ryobi

Ryobi R18IW3 Manual de usuario

Parkside

Parkside PDSSA 20-Li A1 Manual de usuario

Flex

Flex FX1471 Manual de usuario

SATA

SATA 51075C Manual técnico

Cembre

Cembre NR-11P Manual de usuario

Makita

Makita BTP131RFE Manual de usuario

DeWalt

DeWalt XR Li-ion DCF902 Manual de usuario